bulb MAZDA 6 2002 Workshop Manual Suplement

T–20
EXTERIOR LIGHTING SYSTEM
REAR AUTO LEVELING SENSOR REMOVAL/INSTALLATIONA6E8112510302011. Disconnect the negative battery cable.
2. Jack up the vehicle.
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
5. Adjust the headlight zeroset.
End Of SieHIGH-MOUNT BRAKE LIGHT REMOVAL/INSTALLATIONA6E811251580201In-vehicle-type
1. Disconnect the negative battery cable.
2. Remove the liftgate upper trim.
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
EXTERIOR LIGHTING SYSTEM
1 Connector
2Bolt
3Bracket
4 Rear auto leveling sensor
2
1
3
4
4
6.9—9.8 N·m {70—99 kgf·cm, 61—85 in·lbf}
REAR STABILIZER
3
A6E81121158
1 Connector
2Socket
3 High-mount brake light bulb
4 High-mount brake light
12
3HOOK
LIFTGATE
4
A6A8112W113

EXTERIOR LIGHTING SYSTEM, INTERIOR LIGHTING SYSTEM
T–21
T
Rear spoiler type
1. Disconnect the negative battery cable.
2. Remove the rear spoiler.
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
CARGO COMPARTMENT LIGHT REMOVAL/INSTALLATIONA6E8114514412011. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
Lens Removal Note
1. Insert a tape-wrapped flathead screwdriver into
the service hole.
2. Twist the flathead screwdriver as indicated by the
arrow to remove the lens.
End Of Sie
1Bolt
2 Cover
3 Connector
4 High-mount brake light
4
12
3
A6J81121004
INTERIOR LIGHTING SYSTEM
1Lens
(See T–21 Lens Removal Note)
2 Cargo compartment light bulb
3 Screw (if equipped)
4 Cargo compartment light
5 Connector
12
33
4
5
A6J81141102
SERVICE HOLE
A6A8114W104

T–22
INTERIOR LIGHTING SYSTEM, WIPER AND WASHER
CARGO COMPARTMENT LIGHT INSPECTIONA6E8114514412021. Remove the cargo compartment light. (See T–21 CARGO COMPARTMENT LIGHT REMOVAL/
INSTALLATION)
2. Inspect for continuity between the cargo
compartment light terminals using an ohmmeter.
•If not as specified, replace the cargo
compartment light.
End Of Sie
REAR WIPER MOTOR REMOVAL/INSTALLATIONA6E8116674502011. Disconnect the negative battery cable.
2. Remove the rear wiper arm and blade. (See T–23 REAR WIPER ARM AND BLADE REMOVAL/
INSTALLATION.)
3. Remove the liftgate lower trim. (See S–24 LIFTGATE LOWER TRIM REMOVAL/INSTALLATION)
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
6. Adjust the rear wiper arm and blade. (See T–24
REAR WIPER ARM AND BLADE
ADJUSTMENT.)
End Of SieREAR WIPER MOTOR INSPECTIONA6E8116674502021. Disconnect the negative battery cable.
2. Remove the liftgate lower trim. (See S–24 LIFTGATE LOWER TRIM REMOVAL/INSTALLATION)
3. Disconnect the rear wiper motor connector.
4. Connect battery positive voltage to the rear wiper motor terminal A, and ground the rear wiper motor terminal B
to a bare metal part of the vehicle.
A
B OFF
DOORAB
**
A6J81141112
: Bulb
Switch position
DOOR
OFFTerminal
B A
A6A81141119
WIPER AND WASHER
1 Connector
2Bolt
3 Rear wiper motor
4 Outer bushing
N·m {kgf·cm, in·lbf}
4
31
2
3.92—6.86
{40.0—69.9,
34.8—60.6}
A6E81161110

TD–8
TECHNICAL DATA
Wheel and Tires
*
1: Total weight exceeds 160 g {5.65 oz}.
*2: One balance weight: 60 g {2.12 oz} max. If the total weight exceeds 100 g {3.53 oz} on one side, rebalance after moving the tire around on the rim. Do not use 3 or more balance weights.
End Of Sie
BODY ELECTRICAL SYSTEMA6E931001047201
End Of Sie
Item Specification
Standard tire and wheel
Wheel Size 15
× 6JJ 16 × 7JJ 17 × 7JJ 18 × 7J
Offset (mm {in}) 50 {1.97} 55 {2.17} 55 {2.17}
Pitch circle diameter (mm {in}) 114.3 {4.50} 114.3 {4.50}
Material Steel Aluminum alloy Aluminum alloy
Tire Size 195/65R15 91V 205/55R16 91V
215/45R17
87W 215/45R17
91W
(reinforced) 215/45R18 89W
Air pressure
(kPa {kgf/
cm
2, psi}) Front
Up to 4
persons
220 {2.2, 32} 2WD: 230
{2.3, 33}
4WD: 250 {2.5, 36} 220 {2.2, 32}
Full load 240 {2.4, 35} 2WD: 240
{2.4, 35}
4WD: 250 {2.5, 36} 240 {2.4, 35}
Rear Up to 4
persons
220 {2.2, 32} 2WD: 230
{2.3, 33}
4WD: 250 {2.5, 36} 220 {2.2, 32}
Full load 300 {3.1, 44} 270 {2.8, 39} 270 {2.8, 39}
Remaining tread (mm {in}) 1.6 {0.06} 1.6 {0.06}
Wheel
and
tire Wheel and tire
runout
Radial
direction
1.5 {0.06} max. 1.5 {0.06} max.
(mm {in}) Lateral direction 2.5 {0.10} max. 2.0 {0.08} max. 2.0 {0.08} max.
Wheel imbalance (g {oz}) Knock-type*
2:
9 {0.32} max. Adhesive-type*
1:
13 {0.46} max.
Knock-type*
2:
8 {0.28} max. Adhesive-type*
1:
11 {0.39} max.
Knock-type*
2:
7 {0.25} max. Adhesive-type*
1:
10 {0.35} max.
Knock-type*
2:
6 {0.21} max.
Temporary spare tire
Wheel Size 15
×4T
Offset (mm {in}) 40 {1.57}
Pitch circle diameter (mm {in}) 114.3 {4.50}
Material Steel
Tire Size T115/70 D15 T135/90 D15
Air pressure
(kPa {kgf/cm
2,
psi}) 420 {4.2, 60}
Wheel
and
tire Wheel and tire
runout
Radial
direction
2.0 {0.08} max.
(mm {in}) Lateral direction 2.5 {0.10} max.
Item Specifications
Exterior light bulb capacity (W) High-mount brake
lightWGNIn-vehicle-type 18.4
× 1
Rear spoiler
type 4
× 1 (LED)
Interior light bulb capacity (W) Cargo compartment light 10 × 1