boot MAZDA 626 1987 Repair Manual

1 3 REAR SHOCK ABSORBER AND SPRING
DISASSEMBLY AND ASSEMBLY
1. Disassemble in the sequence shown in the figure the referring to the disassembly note for specially
marked parts.
2. Inspect all components and parts, referring to inspection note.
3. Assemble in the reverse order of disassembly, referring to the assembly note for specially marked
parts.
4. Tighten all nuts and bolts to the specified torque, referring to the figure.
76G13X022
1. Nut
2. Seat
3. Mounting block
4. Spring seat 7. Coil spring
5. Dust boot 8. Shock absorber
6. Bound stopper
Disassembly Note
1. Loosen the piston rod upper nut several turns, but
do not remove.
Caution
a) Do not remove the nut.
b) Use copper or aluminum plates in the jaws
of the vise.
2. Set the SST in a vise.
3. Secure the shock absorber in the SST.
4. Compress the coil spring with the SST, then re-
move the nut.
5. Remove the coil spring. 86U13X-061
13-32

REAR SHOCK ABSORBER AND SPRING 1 3
86U13X062
86U13X-063
86U13X-064
Inspection Note
Check the following and repair or replace any faulty
parts.
1. Oil leakage or noise from shock absorbers
2. Deterioration or damage of mounting block
3. Wear or damage of bound stopper
4. Rotation of the control rod (AAS).
Assembly Note
1. Set the SST in a vise
2. Secure the shock absorber in the SST.
3. Install the bound stopper and dust boot onto the
shock absorber.
4. Install the compressed coil spring (compressed
with SST).
5. Install the spring seat and mounting block.
6. Remove the SST.
7. Secure the mounting blocks in the vise.
Caution
Use copper or aluminum plate in the jaws of
a vice.
8. Tighten the piston rod upper nut.
Tightening torque:
64—84 N-m (6.5—8.2 m-kg, 47—59 ft-lb)
Caution
Check that the spring is well seated in the up-
per seats.
76G13X-023
13—33

REAR LOWER ARM AND TRAILING LINK (4WS) 1 3
Inspection Note
Check the following and repair or replace any faulty
parts.
1. Deformation or cracks in lower arm and trailing link
2. Deformation or wear of bushing
3. Rotation torque of ball joint
Note
If it is necessary to replace the ball joint,
replace the lower arm assembly.
86U13X-071
Measurement of ball joint rotation torque
Connect the SST to the ball stud, then measure by
using a pull scale.
Rotation torque: 1.8—3.1 N-m
(18—31 cm-kg, 15.6—26.9 in-lb)
pull scale reading: 18—30 N
(1.8—3.1 kg, 3.9—6.8 lb)
86U13X-072
Dust boot
Removal
Use a chisel to remove the dust boot.
Caution Do not damage the ball joint.
86U13X-073
Installation
Apply lithium grease to the inside of the new dust
boot, then install it with the SST.
76G13X-026
13—37

1 3 REAR STABILIZER AND CONTROL LINK (4WS)
86U13X-084
86U13X-085
86U13X-086
Removal Note
1. Remove the rear steering cover bolts.
2. Remove the stabilizer bar control link.
Inspection Note
Check the following and repair or replace any faulty
parts.
1. Worn or deteriorated rubber bushing
2. Bent, deteriorated, or damaged stabilizer
3. Damaged control link
4. Damaged control link dust boot
5. Worn or deteriorated bushing
Note
If it is necessary to replace the ball joint, re-
place the control link assembly.
86U13X-087
13-42

40 SPECIAL TOOLS
AUTOMATIC TRANSAXLE
TOOL NUMBER & DESCRIPTION PRIORITY ILLUSTRATION

49 G019 0A7A
Compressor set, Return spring
A
49 G019 0A5A
Shim selector set A
a

x|mJen
It
49 0378 400A
Gauge set,
oil

pressure
A

lal

49 G019 011
Bearing installer A
mm H

49 FT01
376

Lifter, servo
piston
(3AT)
A
49 S120 785
Dsut boots
installer
A
49 FT01
377

Replacer,
low
reverse piston (3A1)
A

fl
jr "

49 FT 01
374

Holder,
one
way clutch position (3AT1
A

TOOL NUMBER & DESCRIPTION PRIORITY ILLUSTRATION

49 G032 355
Adjust gauge (3 AT) B
49 G019 9A2
Tester set, EC-AT
(EC-AT)
A
J3||
i®
49 G019 013
Bearing
remover
A

©5

49 G019 022
Attachment
K
A
49 FT01
439

Holder, idle
gear shaft
A
49 G019 012
Leak checker A

I

49 G019 0A2
Turbine shaft holder A

•o

49 0378 375
Compressor, clutch spring (3AT)
A i

U
40-6

40 SPECIAL TOOLS
TOOL NUMBER & DESCRIPTION PRIORITY ILLUSTRATION

49 F027 005
Attachment
62
A

®
STEERING
TOOL NUMBER & DESCRIPTION PRIORITY ILLUSTRATION

49 0118 850C
Puller, ball joint B
49 0180 51 OB
Attachment B

jr

49 B032 302
Adapter A
49 H002
671

Adapter, pow-er steering gauge
A
49 W023 585A
Adjust wrench A



49 8038
785

Boot installer,
ball joint dust
cover
A

40—8
TOOL NUMBER & DESCRIPTION PRIORITY ILLUSTRATION

49 M005 795
Installer set,
oil
seal A

TOOL NUMBER & DESCRIPTION PRIORITY ILLUSTRATION

49 1243 785
Boots installer, tie rod B

®

49 0208 701A
Air out tool,
boot
B
49 1232 670A
Gauge set,
power steering
A
49 G033
108

Adapter, caster camber gauge
A
49 0727 575
Puller, socket
joint
(4WS)
B

4F

49 G032 3A1
Joint hose A