water MAZDA 626 1987 Repair Manual

3B OUTLINE
OUTLINE
COOLANT FLOW CHART
76G03B-002
1. Water pump 4. Coolant reservoir
2. Thermostat 5. CSD coolant passage
3. Radiator 6. Oil cooler
3B-2

TROUBLESHOOTING GUIDE
3B

SPECIFICATIONS

Cooling system Water-cooled, forced circulation
Coolant capacity liters (US
qt,
Imp
qt)

With heater 9.5 (10.0, 8.4) Coolant capacity liters (US
qt,
Imp
qt)

Without heater 9.0 (9.5, 7.9)
Water pump Type Centrifugal, timing belt driven Water pump
Water seal Unified mechanical seal
Thermostat
Type Wax, two stage
Thermostat
Opening temperature °C(°F) Main Sub
Thermostat
Opening temperature °C(°F)
86.5-89.5 (188-193) 78.5—81.5 (173-179) Thermostat
Full-open temperature °C(°F) 100 (212) 100 (212)
Thermostat
Full-open lift
mm (in)
8.0 (0.31) min. 1.5 (0.06) min.
Radiator
Type Corrugated
fin

Radiator Cap valve opening pressure
kPa (kg/cm2,
psi)
74-103 (0.75-1.05, 11—15)
Cooling
fan

Type Electric
Cooling
fan

Capacity
W
120
Cooling
fan
Switching temprature orvopi OFF
- ON ^
91 (196) Cooling
fan

Number
of
blade 4
Cooling
fan

Outer diameter
mm
(in) 340 (13.4)

76G03B-003
TROUBLESHOOTING GUIDE
Problem Possible Cause Remedy Page
Overheating
Insufficient coolant Add 3B-
4

Coolant leakage Repair
—

Radiator fins clogged Clean 3B—
6

Radiator cap malfunction Replace 3B—
5

Cooling fan malfunction Repair 3B-11 Thermostat malfunction Replace 3B—
9

Water passage clogged Clean 3B—
4

Water pump malfunction ReDair
or
replace 3B—
7

Corrosion
Impurities
in
coolant Replace 3B-
4

76G03B-004
3B—3

RADIATOR CAP 3B
86U03X-028
86U03X-007
86U03X-008
3. Set the heater control switch to the maximum heat
position.
4. Flush the cooling system with water until all traces
of color are gone, then let the system drain com-
pletely.
5. Fill with the proper mixture and amount of ethy-
lene glycol-based coolant.
Caution
a) Do not use alcohol- or methanol-based
coolant.
b) Use only soft (demineralized) water in the
coolant mixture.
Anti-freeze solution mixture percentage

Protection Volume percentage Gravity
at

20°C (68°F) Protection Solution Water
Gravity
at

20°C (68°F)
Above —16°C (3°F) 35 65 1.054
Above -26°C (-15°F) 45 55 1.066
Above -40°C (-40°F) 55 45 1.078

6. Run the engine at idle with the radiator cap re-
moved. Let any air bleed from the system, and add
more coolant.
7. Install the radiator cap, and inspect all connections
for leakage.
RADIATOR CAP
INSPECTION
Radiator Cap Valve
1. Remove foreign material (such as water residue)
from between the radiator cap valve and the valve
seat.
2. Attach the radiator cap to a tester with the SST.
Apply pressure gradually to 74—103 kPa
(0.75—1.05 kg/cm2, 11—15 psi).
3. Wait about 10 seconds; then check that the pres-
sure has not decreased.
Negative Pressure Valve
1. Pull the negative-pressure valve to open it. Check
that it closes completely when released.
2. Check for damage on the contact surfaces, and
for cracked or deformed seal packing.
3. Replace the radiator cap if necessary.
86U03X-009
3B-5

3B RADIATOR
Note
a) Position the hose clamp in the original location on the hose.
b) Squeeze the clamp lightly with large pliers to ensure a good fit. 86U03X-010
RADIATOR
REMOVAL AND INSTALLATION
1. Drain the engine coolant.
2. Remove in the sequence shown in the figure.
3. Install in the reverse order of removal.
1. Coolant reservoir hose
2. Fast idle solenoid
3. Coolant level sensor connector
4. Cooling fan connector
76G03B-005
5. Upper and lower radiator hose
6. Cooling fan and radiator assembly
7. Cooling fan
INSPECTION
Check the following points. Repair or replace if
necessary.
1. Cracks, damage, or water leakage
2. Bent fins (Repair with a screwdriver)
3. Distorted or bent radiator inlet
86U03X-012
3B-6

WATER PUMP 3B
WATER PUMP
REMOVAL
1. Disconnect the negative battery cable.
2. Turn the crankshaft so that the No. 1 cylinder is at TDC of compression.
3. Drain the engine coolant.
4. Remove in the sequence shown in the figure. 69G03A-025
31—46 N m (3.2—4.7 m-kg, 23—34 ft-lb)
19—26 N-m (1.9—2.6 m-kg, 14—19 ft-lb)
(?) 8—11 N-m (80—110 cm-kg, 69—95 In-lb)
37—52 N-m (3.8—5.3 m-kg, 27—38 ft
55—65 N-m (5.6—6.6 m-kg, 41-48 ft-lb)
(80—110 cm-kg, 69—95 In-lb)
59—69 N-m (6.0—7.0 m-kg, 43—51 ft-lb)
76G03B-006
1. Timing belt (Refer to page 1C—11)
2. Camshaft pulley (Refer to page 1C—36)
3. Injection pump pulley (Refer to page
1C—36)
4. Seal plate
Note
Do not disassemble the water pump body, if a problem is found replace it as a unit.
5. Alternator
6. Water pipe
7. Water hose
8. Water pump body
9. Water pump inlet
3B-7

3B WATER PUMP
INSPECTION
Check the following. Replace the pump if necessary.
1. Cracks or damage
2. Abnormal noise, bearing sticking or loose
86U03X-014
INSTALLATION
Install in the reverse order of removal referring to the
installation note.
Installation Note
Water pump
1. Remove any gasket fragments, dirt or oil from the
contact surfaces.
2. Install the water pump and new gasket so that the
printed side of the gasket faces the water pump.
Tightening torque:
Bolt A: 31—46 N-m
(3.2—4.7 m-kg, 23—34 ft-lb)
Bolt B: 8—11 N-m
(80—110 cm-kg, 69—95 in-lb)
Water pipe
1. Apply a coat of vegetable oil to the O-ring.
2. Install the water pipe.
Tightening torque:
8—11 N-m (80—110 cm-kg, 69—95 in-lb)
3. Connect the water hose.
76G03B-008
Alternator
1. Install the alternator.
Tightening torque:
Bolt A: 19—26
N
m
(1.9—2.6 m-kg, 14—19 ft-lb)
Bolt B: 37—52 N-m
(3.8—5.3 m-kg, 27—38 ft-lb)
2. Install the alternator drive belt and Comprex su-
percharger drive belt, and adjust the belt deflec-
tion. (Refer to page 1C—7)
76G03B-009
3B—8

THERMOSTAT 3B
THERMOSTAT
REMOVAL
1. Drain the engine coolant.
2. Disconnect the upper radiator hose, and water
thermo switch connector.
3. Remove the thermostat cover.
4. Remove the thermostat.
76G03B-010
76G03B-011
Sub valve Main valve
I
INSPECTION
Check the thermostat. Replace if necessary.
1. Visually check that the valve is airtight.
2. Place the thermostat and a thermometer in water.
3. Gradually heat the water and check the following:
Valve opening temperature
Sub valve : 78.5—81.5°C (173—179°F)
Main valve : 86.5—89.5°C (188—193°F)
Full open lift
Sub valve : 1.5 mm (0.06 in) min. at
100°C (212°F)
Main valve : 8 mm (0.31 in) min. at
100°C (212°F)
Valve closing temperature
Sub valve : 75°C (167°F)
Main valve : 83°C
(181
°F)
69G03B-012
76G03B-012
INSTALLATION
1. Install the thermostat into the thermostat case with
jiggle pin at the top.
2. Install a new gasket with the seal print side facing
the thermostat case.
3. Install the thermostat cover.
Tightening torque:
7—10 N-m (70—100 cm-kg, 61—87 in-lb)
4. Install the upper radiator hose and water thermo
switch connector.
5. Replenish the coolant.
6. Start the engine and check for leaks.
3B-9

3B COOLING FAN
COOLING FAN
SYSTEM CIRCUIT
I
IG1 IG Relay Main fuse
©
Main fan motor
V-f motor
IG1
Water thermo switch OFF: over 91°C (208 °F)
Water thermo switch ON:
below 84°C
(183°F)
76G03B-015
CIRCUIT INSPECTION
1. Turn the ignition switch ON.
2. Disconnect the water thermo switch connector, and
check that the fan begins to operate.
3. If the fan doesn't operate, check the fuse, fan re-
lay, fan motor, thermo switch, and wiring harness.
76G03B-016
3B—10

3B COOLING FAN
WATER THERMO SWITCH
1. Remove the cooling fan water thermo switch.
Note
Make sure that the ignition switch is OFF. If
not, the fan will operate when the connector
is removed.
76G03B-017
76G03B-018
2. Place the water thermo switch in water.
3. Heat the water gradually, and check for continui-
ty of the switch with an ohmmeter. Replace if
necessary.
Temperature Continuity
Above
91
°C (208°F) No
Below 84°C (183°F) Yes
4. Install the water thermo switch and a new O-ring.
Tightening torque:
6—9 N-m (60—90 cm-kg, 52—78 in-lb)
Caution
Do not use sealing tape.
3B-12

4A
FUEL AND EMISSION
CONTROL SYSTEMS
(CARBURETOR)
OUTLINE 4A— 2
SYSTEM DIAGRAM 4A— 2
VACUUM HOSE ROUTING
DIAGRAM 4A— 5
EMISSION COMPONENTS
LOCATION 4A— 8
COMPONENT DESCRIPTIONS 4A—12
SPECIFICATIONS 4A—15
TROUBLESHOOTING GUIDE 4A—17
PARTS INSPECTION 4A—23
AIR CLEANER ELEMENT 4A—23
ACCELERATOR LINKAGE 4A—23
INTAKE MANIFOLD 4A—23
CHOKE CABLE 4A—23
FUEL SYSTEM 4A—24
TROUBLESHOOTING 4A—25
CARBURETOR 4A—26
FUEL PUMP 4A—35
FUEL TANK 4A—36
SEPARATOR 4A—37
TWO-WAY CHECK VALVE 4A—37
THREE-WAY CHECK VALVE 4A—37
FUEL FILTER 4A—37
IDLE SPEED AND IDLE MIXTURE.. 4A—38
ADJUSTMENT 4A—38
AUTO-RETURN CHOKE SYSTEM... 4A—40
TROUBLESHOOTING 4A—40
PTC HEATER SYSTEM 4A—42
TROUBLESHOOTING 4A—42
DECELERATION CONTROL SYSTEM 4A—45
TROUBLESHOOTING 4A—45
BYPASS AIR CONTROL SYSTEM.. 4A—48
DASH POT 4A—50
ANTI-AFTERBURN VALVE 4A—50
MAIN AIR BLEED CONTROL
SYSTEM 4A—51
SLOW FUEL CUT SYSTEM 4A—53
COAST ENRICHMENT SYSTEM .... 4A—54
COASTING LEANER SYSTEM 4A—56
AIR INJECTION SYSTEM 4A—58
INTAKE AIR TEMPERATURE CONTROL
SYSTEM 4A—60
TROUBLESHOOTING 4A—60
PURGE CONTROL SYSTEM 4A—63
VACUUM SWITCH VALVE 4A—63
EXHAUST GAS RECIRCULATION
(EGR) SYSTEM 4A—64
TROUBLESHOOTING 4A—65
POSITIVE CRANKCASE VENTILATION
SYSTEM 4A—67
PCV VALVE 4A—67
IDLE-UP CONTROL SYSTEM 4A—68
TROUBLESHOOTING 4A—70
IDLE-UP SOLENOID VALVE 4A—76
EVAPORATIVE EMISSION CONTROL
SYSTEM 4A—78
TROUBLESHOOTING 4A—79
IGNITION TIMING CONTROL
SYSTEM 4A-80
TROUBLESHOOTING 4A—81
CONTROL SYSTEM 4A-83
RELATIONSHIP CHART 4A—84
ENGINE CONTROL UNIT 4A—86
INHIBITOR SWITCH 4A—93
IDLE SWITCH 4A—93
VACUUM SWITCH 4A—94
WATER THERMO SWITCH 4A—95
EXHAUST SYSTEM 4A—96
76G04A-001