Jack MAZDA CX90 2024 Owners Manual

Floor Mat............................... 7-74Warnings and Cautions For Using
the Floor Mat...................... 7-74
Malfunction Diagnosis
Connector............................. 7-75 Malfunction Diagnosis
Connector...........................7-75Spare Tire and Tool Storage...... 7-76Jack.................................... 7-76
Spare Tire............................ 7-77
7-3
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Warning and Cautions forUsing the Rear Coat Hooks
WARNING
Never hang heavy or sharp objects on
the assist grips and coat hooks.
Hanging heavy or sharp-ended objects
such as a coat hanger from the assist
grips or coat hooks is dangerous as
they can fly off and hit an occupant in
the cabin if a curtain air bag was to
deploy, which could result in serious
injury or death.
How to Use the Rear
Coat Hooks
Use the rear coat hooks when hanging
a coat or jacket.
Other Equipment
Rear Coat Hooks
7-37
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Trailer tire size, load rating, and inflation pressures should conform to tire
manufacturer specifications.
Do not exceed 100 km/h (62 mph) with a trailer in tow. If the local legal
maximum speed with a trailer in tow is less than 100 km/h (62 mph), do not
exceed the legal speed.
Safety chains
Safety chains must be used as a precautionary measure should the trailer become
unintentionally unhitched. They should cross under the trailer tongue and attach to
the hitch. Leave enough slack to allow full turns. Consult literature published by your
trailer or hitch manufacturer for more details.
Tra i l e r l i g h t s
Trailer lights must comply with all federal, state, and local regulations. Equip your
trailer as required before towing it day or night.
Trailer brakes
If the total trailer weight exceeds 450 kg (1,000 lb), trailer brakes are required. If
your trailer has brakes, make sure they comply with all federal, state, and local
regulations.
Driving
Your Mazda will handle differently with a trailer in tow, so practice turning ,
backing , and stopping in a traffic-free area.
Take time to get accustomed to the extra weight and length.Allow more room between your vehicle and the one in front because braking
distance increases with a trailer. For each 16 km/h (10 mph) of speed, allow at
least one vehicle and trailer length between your Mazda and the vehicle ahead.
Avoid jerky starts or sudden acceleration.Avoid sudden braking. It may cause loss of control and result in
jackknifing,
especially so on wet or slippery roads.
Shift the selector lever to the D position when towing a trailer in hilly terrain or
when heavily loaded.
The D position will allow operating the vehicle without frequent shifting.
Lane changes and turning
Avoid quick lane changes, sudden turns, and tight turns. Slow down before turning
to avoid the need of sudden braking.
A turning trailer will make a tighter arc than the tow vehicle. Compensate with turns
that are larger than normal.
Pa s s i n g
Plan well ahead to pass other vehicles, and provide plenty of room before changing
lanes. Crosswinds from passing vehicles, especially larger ones, and the effects of
rough roads will affect handling.
Other Equipment
Towing (U.S.A. and Canada)
7-65
CX-90_8KG7-EA-22L_Edition1_new
2022-11-17 16:05:04

Jack
To r e m o v e t h e j a c k
1. Remove the luggage board.
2. Remove the cargosub-compartment.
3. Turn the wing bolt and jack screwcounterclockwise.
1. Wing bolt
2. Jack screw

To s e c u r e t h e j a c k
1. Insert the wing bolt into the jack
with the jack screw pointing to the
right side and turn the wing bolt
clockwise to temporarily tighten it.
2. Tighten the jack screw clockwise.
1. Wing bolt
2. Jack screw
3. Turn the wing bolt completely to secure the jack.

Maintenance
Always keep the jack clean.Make sure the moving parts are kept
free from dirt or rust.
Make sure the screw thread is
adequately lubricated.
Other Equipment
Spare Tire and Tool Storage
7-76
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Using the Towing Hooks
CAUTION
Do not use the front and rear tiedown
eyelets for towing the vehicle.
They have been designed only for
securing the vehicle to a transport
vessel during shipping.
Using the eyelets for any other purpose
could result in the vehicle being
damaged.

1. Remove the tiedown eyelet, thejack lever and the lug wrench or
equivalent from the luggage
compartment.
1. Lug wrench
2. Tiedown eyelet
3. Jack lever

2. Wrap a flathead screwdriver or jack lever or a similar tool with a soft
cloth to prevent damage to a
painted bumper, and open the cap
located on the front or rear
bumper.
Front
Rear

CAUTION
Do not use excessive force as it may
damage the cap or scratch the
painted bumper surface.
NOTE
Remove the cap completely and
store it so as not to lose it.

3. Securely install the tiedown eyelet
using the lug wrench, the jack lever
or equivalent.
What to Do in Case of Emergency
When Towing is Required
8-6
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Front
1. Lug wrench
2. Tiedown eyelet
Rear
1. Jack lever
2. Tiedown eyelet

4. Hook the tying rope to the tiedown eyelet.
CAUTION
If the tiedown eyelet is not securely
tightened, it may loosen or
disengage from the bumper when
tying the vehicle. Make sure that
the tiedown eyelet is securely
tightened to the bumper.
What to Do in Case of Emergency
When Towing is Required
8-7
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Changing a Flat Tire (WithSpare Tire)
NOTE
If the following occurs while driving , it
could indicate a flat tire.
Steering becomes difficult.The vehicle begins to vibrate
excessively.
The vehicle pulls in one direction.
If you have a flat tire, drive slowly to a
level spot that is well off the road and
out of the way of traffic to change the
tire.
Stopping in traffic or on the shoulder
of a busy road is dangerous.
WARNING
Do not install the temporary spare tire
on the rear wheels (driving wheels).
Driving with the temporary spare tire
on one of the rear driving wheels is
dangerous. Handling will be affected.
You could lose control of the vehicle,
especially on ice or snow bound roads,
and have an accident. Move a regular
tire to the rear wheel and install the
temporary spare tire to the front.
Be sure to follow the directions for
changing a tire.
Changing a tire is dangerous if not
done properly. The vehicle can slip off
the jack and seriou sly injure someone.
No person should place any portion of
their body under a vehicle that is
supported by a jack.
Never allow anyone inside a vehicle
supported by a jack.
Allowing someone to remain in a
vehicle supported by a jack is
dangerous. The occupant could cause
the vehicle to fall resulting in serious
injury.
NOTE
Make sure the jack is well lubricated
before using it.
1. Park on a hard, level surface off the
right-of-way and firmly set the
parking brake.
2. Shift into Park (P) and turn off the
engine.
3. Turn on the hazard warning flasher.
4. Have passengers get out of the
vehicle and away from the vehicle
and traffic.
5. Remove any luggage, the jack (page
7-76), spare tire (page 7-77), and
tools.
1. Lug wrench
2. Jack lever
6. Block the wheel diagonally opposite the flat tire. When
blocking a wheel, place a tire block
both in front and behind the tire.
What to Do in Case of Emergency
Tire is Punctured or Bursts
8-22
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

NOTE
When blocking a tire, use rocks or
wood blocks of sufficient size if
possible to hold the tire in place.
Removing a Flat Tire
WARNING
When jacking-up a vehicle, always
shift the selector lever to P position,
apply the parking brake, and place
wheel blocks in the position
diagonally opposed to the jack.
Changing a flat tire without using
wheel blocks is dangerous because the
vehicle may move and fall off the jack
even with the selector lever is in P
position, which could result in an
accident.
1. Loosen the lug nuts by turning them counterclockwise one turn each,
but do not remove any lug nuts
until the tire has been raised off the
ground.
NOTE
If your Mazda is equipped with the
optional antitheft wheel lug nuts, a
special key must be used to unlock
the locking lug nut for each wheel.
For details, refer to “Locking Lug
Nuts” below.
2. Place the jack on the ground.
3. Turn the jack screw in the direction shown in the figure and adjust the
jack head so that it is close to the
jack-up position.
4. Place the jack under the jack-upposition closest to the tire being
changed with the jack head
squarely under the jack-up point.
5. Continue raising the jack headgradually by rotating the screw with
your hand until the jack head is
inserted into the jack-up position.
What to Do in Case of Emergency
Tire is Punctured or Bursts
8-23
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

WARNING
Use only the front and rear jacking
positions recommended in this
manual.
Attempting to jack the vehicle in
positions other than those
recommended in this manual is
dangerous. The vehicle could slip
off the jack and seriously injure or
even kill someone. Use only the
front and rear jacking positions
recommended in this manual.
Do not jack up the vehicle in a
position other than the designated
jack-up position or place any
objects on or under the jack.
Jacking up the vehicle in a position
other than the designated jack-up
position or placing objects on or
under the jack is dangerous as it
could deform the vehicle body or
the vehicle could fall off the jack
resulting in an accident.
Use only the jack provided with
your Mazda.
Using a jack that is not designed for
your Mazda is dangerous. The
vehicle could slip off the jack and
seriously injure someone.
Never place objects under the
jack.
Jacking the vehicle with an object
under the jack is dangerous. The
jack could slip and someone could
be seriously injured by the jack or
the falling vehicle.
NOTE
When raising the jack head into the
jacking position and aligning the
groove in the jack head with the rail
under the vehicle body, the top of
the jack head contacts the vehicle's
underbody without the rail
contacting the bottom of the
groove.
6. Insert the jack lever and attach the lug wrench to tire jack.
7. Turn the jack handle clockwise andraise the vehicle high enough so
that the spare tire can be installed.
Before removing the lug nuts, make
sure your Mazda is firmly in
position and that it cannot slip or
move.
WARNING
Do not jack up the vehicle higher
than is necessary.
Jacking up the vehicle higher than is
necessary is dangerous as it could
destabilize the vehicle resulting in
an accident.
What to Do in Case of Emergency
Tire is Punctured or Bursts
8-24
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Do not start the engine or shake
the vehicle while it is jacked up.
Starting the engine or shaking the
vehicle while it is jacked up is
dangerous as it could cause the
vehicle to fall off the jack resulting
in an accident.
Never go under the vehicle while it
is jacked up.
Going under the vehicle while it is
jacked up is dangerous as it could
result in death or serious injury if
the vehicle were to fall off the jack.
8. Remove the lug nuts by turning them counterclockwise; then
remove the wheel and center cap.
Locking Lug Nuts
If your Mazda is equipped with the
optional antitheft wheel lug nuts, a
special key must be used to unlock the
locking lug nut for each wheel. The key
is stored in the glove compartment,
center console storage, storage box, or
trunk. Register the key and lug nuts
with the lock manufacturer by filling
out the registration card and mailing it
in using the accompanying envelope. If
the key is lost, consult an Authorized
Mazda Dealer or use the lock
manufacturer’s order form to order a
new key.
Antitheft wheel lug nuts cannot be
installed on a steel wheel spare tire.
When installing a temporary spare tire,
use one of the original lug nuts in place
of the locking lug nut. The original lug
nuts are stored inside your Mazda.
1. Antitheft lug nut
2. Special key
To remove an antitheft lug nut
1. Obtain the special key for the antitheft lug nut.
2. Place the special key on top of the antitheft lug nut, and be sure to
hold the key square to it. If you
hold the key at an angle, you may
damage both key and nut. Do not
use a power impact wrench.
3. Place the lug wrench on top of the key and apply pressure. Turn the
wrench counterclockwise.
To install the antitheft lug nut
1. Place the special key on top of the nut, and be sure to hold the key
square to it. If you hold the key at
an angle, you may damage both key
and nut. Do not use a power
impact wrench.
2. Place the lug wrench on top of the special key, apply pressure, and
turn it clockwise.
Nut tightening torque
N·m (kgf·m, ft·lbf) 108―
147 (12 ―14,
80― 108)
What to Do in Case of Emergency
Tire is Punctured or Bursts
8-25
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04