sensor MAZDA CX90 2024 Owner's Manual

How to Use the DoorLock
To prevent the key from being left in
the vehicle, make sure that you carry
the key before locking.
Locking/Unlocking Using the Key
Refer to How to Use the Key on page
4-5.
Locking/Unlocking Using the Touch
Sensor (Vehicles with Advanced
Keyless Function)
Locking
Touch the sensing area of the door lock
touch sensor when all of the following
conditions are met.
The vehicle power is switched OFF.All the doors are closed.The key is on the sensing area of the
touch sensor.
The hazard warning lights operate
once, and all the doors, liftgate,
fuel-filler lid/charging port lid are
locked.
A beep sound operates one time.
Unlocking
When all of the following conditions
are met, touch the sensing area of the
door release touch sensor.
The vehicle power is switched OFF.The driver’s door is locked.Three seconds or longer have passed
since the doors were locked.
The key is on the sensing area of the
touch sensor.
Unlocking from the driver's door
The following locations are unlocked
by touching the sensing area of the
door release touch sensor of the
driver's door.
Driver’s doorCharging port lid

When unlocking , the hazard warning
lights operate two times.
A beep sound operates two times.
Unlocking from the front passenger’s
door
The following locations are unlocked
by touching the sensing area of the
door release touch sensor of the front
passenger's door.
All doorsCharging port lidLiftgate
When unlocking , the hazard warning
lights operate two times.
A beep sound operates two times.
NOTE
The location to be unlocked can be
changed.
Refer to Settings section in the
Mazda Connect Owner's Manual or
consult an Authorized Mazda Dealer.
Opening/closing
Doors
4-12
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

The beep sound can be turned
on/off using Mazda Connect.
Refer to Settings section in the
Mazda Connect Owner's Manual or
consult an Authorized Mazda Dealer.
The system may not operate normally
under the following conditions.
You touch the sensing area of the
door lock touch sensor and the
sensing area of the door release
touch sensor at the same time.
You touch the sensing area of the
touch sensor while wearing gloves.
Foreign matter such as water, ice,
snow, or dirt is on the detection
area of the touch sensor.
The system may operate if the outer
side door handle of a front door is
splashed with water by a car wash or
rain while the key is in the operation
range.
Locking/Unlocking Using the
Door-Lock Switch
The following locations are locked/
unlocked.
All doorsLiftgateFuel-filler lid (locking only)
Charge port lid
1. Unlocking
2. Locking
Locking the doors from the outside
using the door-lock switch
Doors can be locked from the outside
of the vehicle without using the
transmitter.
You can lock the doors by pressing the
lock side of the door-lock switch with
all of the following conditions met,
and then closing all the doors.
The vehicle power is switched OFF.Any door is open.The key is not in the vehicle.
After locking by pressing the door-lock
switch, closing all the doors with the
transmitter left in the vehicle unlocks
all doors, the liftgate, and the fuel-filler
lid/charging port lid.
Door-lock switch on liftgate (With the
advanced keyless function)
With power liftgate
Refer to How to Use the Power Liftgate
on page 4-21.
Without power liftgate
When all of the following conditions
are met, press the door-lock switch
and then close the liftgate.
Opening/closing
Doors
4-13
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Convenient Ways to Usethe Doors
Proximity Type Auto Lock Function
You can set the vehicle to lock
automatically when you leave the
detection area of the touch sensor.
Refer to Mazda Connect Owner's
Manual or consult an Authorized
Mazda Dealer.
A sound is activated one time when
closing all the doors and the liftgate
while the key is being carried.
If you proceed to leave the operation
range, the vehicle is locked
automatically (it is locked
automatically after about 30 seconds
even if you do not leave the operation
range).
NOTE
However, they are not locked under
the following conditions.
Another key is left inside the vehicle.The driver’s door is already locked.
Auto re-lock function
The vehicle is locked automatically by
the auto re-lock function if you do not
perform any of the following
operations within about 60 seconds
after touching the detection area of the
touch sensor or unlocking with the key.
Open any door or liftgate.Switch the vehicle power to a
position other than OFF.
The time required until automatic
locking occurs can be changed.
Refer to Mazda Connect Owner's
Manual or consult an Authorized
Mazda Dealer.
Opening/closing
Doors
4-16
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Always make sure that there is no
person or obstruction around the
liftgate before closing the liftgate.
The jam-safe function detects a person
or obstruction to prevent the person or
object from getting caught. The system
may not detect certain objects
obstructing the liftgate depending on
the way they are positioned and their
shape. Be especially careful with
children. It may result in an injury if a
finger gets pinched.
CAUTION
When closing the liftgate, make sure
that there is no foreign matter
around the striker. If foreign matter is
obstructing the striker, the liftgate
may not close properly.
1. Striker
 Do not install accessories to the
liftgate other than those
specified.
Otherwise, the liftgate may not
open/close automatically resulting in
a malfunction.
 When the liftgate is switched from
automatic to manual operation, the
liftgate may open/close
unexpectedly depending on its
position, resulting in injury.
Be careful that your fingers do not
get pinched in a closing liftgate. The
liftgate finishes closing to the
fully-closed position automatically
after you close it to where it is slightly
ajar. If your fingers get pinched, it
may result in an injury.
 Do not apply excessive force to the
liftgate when closing it. Otherwise, it
could cause a system malfunction.
 Sensors are installed on both ends of
the liftgate. Be careful not to allow
the sensors to be scratched or
damaged by sharp objects.
Otherwise, the liftgate may no longer
open/close automatically. In
addition, if the sensor is damaged
while the liftgate is closing
automatically, the liftgate stops.
1. Sensor
 Do not paint the rear bumper or
install any add-on equipment to it.
Otherwise, the hands-free sensor
may not operate normally.
 If you are carrying the key around the
liftgate or there is another person
around the liftgate who is carrying a
key, do not allow the following to
occur. Otherwise, the hands-free
sensor will operate and the liftgate
may open/close unexpectedly
resulting in an accident.
Opening/closing
Liftgate
4-20
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

The liftgate is not automatically
opening/closing.
The doors, liftgate, and the fuel-filler
lid/charging port lid are locked, the
hazard warning lights operate 1 time.
Then, the liftgate fully closes
automatically.
Opening/closing using the hands-free
function*
Do the kicking motion with all of the
following conditions met while the
vehicle is stopped.
You are carrying the key.The hands-free function is on.The vehicle power is switched to a
position other than ON, or the
selector lever is in P with the vehicle
power switched ON.
A : About 30―50 cm (12―19.7 in)
B : About 10 cm (3.9 in)

When the kicking motion is done
correctly, the hazard warning lights
flash 2 times, a beep sound is
activated, and the liftgate opens/
closes automatically. Be careful not to
contact the liftgate.
Move your foot away from under the
bumper within about 1 second after
moving it under the bumper.
If the kicking motion is done while the
liftgate is opening/closing
automatically, the liftgate will stop. If
the kicking motion is done again, the
liftgate moves in the direction opposite
to the direction it was moving before it
stopped.
CAUTION
Do not do the kicking motion while
wearing footwear which exposes the
feet, such as sandals. If your foot
contacts the hot exhaust pipe, it
could cause serious burns.
 Do not do the kicking motion while
the area where you are standing is
unstable such as a slope or icy road.
Otherwise, you could fall down,
resulting in injury.
NOTE
The hands-free sensor detects in a
range of about 30 cm on both the
left and right sides from the center of
the rear bumper.
The hands-free sensor may not
operate normally under the following
conditions.
Opening/closing
Liftgate
*Some models.4-23
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Your foot remains placed within
the detection area.
You move your foot left and right
within the detection area.
The kicking motion is too fast or
too slow.
Your foot contacts the rear bumper
when doing the kicking motion.
You are wearing shoes such as
rubber boots which do not
conduct electricity well.
There is equipment emitting strong
radio waves near the vehicle.
The detection area of the
hands-free sensor is dirty.
When the detection area of the
hands-free sensor is dirty, wipe it off
with a clean cloth. Before cleaning
the sensor, place the key outside of
its operation range or turn off the
hands-free function using Mazda
Connect.
If the operation using the hands-free
sensor is not possible even though
the operation conditions are met,
consult an Authorized Mazda Dealer.
Hands-free function ON/OFF
switching
The hands-free function can be
switched on/off.
Refer to Mazda Connect Owner's
Manual or consult an Authorized
Mazda Dealer.
To prevent an unintended operation,
turn off the function.
Stopping the liftgate
If any of the following operations is
done, the automatic opening and
closing of the liftgate stops.
The liftgate open/close switch on the
key is pressed.
The power liftgate switch is pressed.The electric liftgate opener is
pressed.
The power liftgate close switch is
pressed.
The door-lock switch on the liftgate
is pressed.
The kicking motion is done.
NOTE
The liftgate cannot be stopped when it
is half open or lower. It moves in the
close direction by the load weight of
the liftgate itself.
The automatic opening/closing of the
liftgate can be stopped using the
kicking motion even if you do not have
the key.
Moving the liftgate again
If any of the following operations is
done, the liftgate moves in the
direction opposite to the direction it
was moving before it stopped.
The liftgate open/close switch on the
key is pressed for 1 second or longer.
The power liftgate switch is pressed
for about 1 second or longer.
The electric liftgate opener is
pressed.
The power liftgate close switch is
pressed.
When the door-lock switch on the
liftgate is pressed, the liftgate
automatically fully closes.
Opening/closing
Liftgate
4-24
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Theft-Deterrent System
If the theft-deterrent system detects an
inappropriate entry into the vehicle,
which could result in the vehicle or its
contents being stolen, the alarm alerts
the surrounding area of an abnormality
by sounding the horn and flashing the
hazard warning lights.

The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
How to Use the
Theft-Deterrent System
How to Arm the System
1. Close the windows and the
panorama sunroof/moonroof*
securely.
2. Switch the vehicle power OFF.
3. Make sure the hood, the doors, and the liftgate are closed.
4. Press the lock button on the transmitter. The hazard warning
lights will flash once.
The following method will also arm
the theft-deterrent system:
Press the door-lock switch
while
any door is open and then close all
of the doors.
( With the advanced keyless
function)
Touch the sensing area of the door
lock touch sensor.
The security indicator light
in
the instrument cluster flashes twice
per second for 20 seconds.
5. After 20 seconds, the system is fully armed.
NOTE
The theft-deterrent system can also
be armed by activating the auto
relock function with all the doors,
the liftgate and the hood closed.
Refer to Transmitter on page 4-5.
The system will disarm if one of the
following operations takes place
within 20 seconds after pressing the
lock button:
Unlocking any door.Opening any door.Opening the hood.Switching the vehicle power ON.
To rearm the system, do the arming
procedure again.
Opening/closing
Security System
4-40*Some models.
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

When the doors are locked by
pressing the lock button on the
transmitter while the theft-deterrent
system is armed, the hazard warning
lights will flash once to indicate that
the system is armed.
Operation
Horn triggering conditions
The horn sounds intermittently and the
hazard warning lights flash for about
30 seconds when the system is
triggered by any one of the following:
Unlocking a door with the auxiliary
key, door lock switch, or an inside
door-lock knob.
Forcing open a door, the hood or the
liftgate.
Opening the hood by operating the
hood release handle.
Switching the vehicle power ON
without using the power switch.
If the system is triggered again, the
lights and horn will activate until the
driver's door or the liftgate is unlocked
with the transmitter.
(With the advanced keyless function)
The lights and horn can also be
deactivated by touching the sensing
area of the door release touch sensor.
NOTE
The liftgate does not open while the
theft-deterrent system is operating.
If the lead-acid battery goes dead
while the theft-deterrent system is
armed, the horn will activate and the
hazard warning lights will flash when
the lead-acid battery is charged or
replaced.
To S t o p t h e A l a r m
A triggered alarm can be turned off
using any one of the following
methods:
Pressing the unlock button on the
transmitter.
Starting the hybrid system with the
power switch.
(With the advanced keyless
function)
Touching the sensing area of the
door release touch sensor.
Pressing the electric liftgate opener
while the key is being carried.
The hazard warning lights will flash
twice.
To Turn Off an Armed System
An armed system can be turned off
using any one of the following
methods:
Pressing the unlock button on the
transmitter.
Starting the hybrid system with the
power switch.
(With the advanced keyless
function)
Touching the sensing area of the
door release touch sensor.
The hazard warning lights will flash
twice.
NOTE
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned off, the hazard
warning lights will flash twice to
indicate that the system is turned off.
Opening/closing
Security System
4-41
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Rear Seat Alert*
The Rear Seat Alert is a system that
reminds the driver to check if any
occupants or luggage have been left
behind on the second/third-row seats.
The Rear Seat Alert determines if there
is the possibility that occupants or
luggage are on a second/third-row
seat based on the opening and closing
history of the rear doors. For this
reason, the system may operate
differently from the actual conditions,
such as it is not activated even if
occupants or luggage are occupying a
second/third-row seat.
Warnings and Cautions
for Using the Rear Seat Alert
WARNING
Do not rely completely on the system.
The Rear Seat Alert is not a system that
detects occupants and luggage using
sensors. Over reliance on the system
could lead to an accident.
When leaving the vehicle, always
visually check the conditions of the
second/third-row seats.
Opening/closing
Rear Seat Alert
4-42*Some models.
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Forward Sensing Camera
(FSC)................................... 5-127Forward Sensing Camera
(FSC)
*............................... 5-127
Radar Sensors.......................5-131 Radar Sensors
*...................5-131
Ultrasonic Sensors.................5-135 Ultrasonic Sensors
*............ 5-135
Cameras.............................. 5-137 Cameras
*.......................... 5-137
Driver Monitoring Camera..... 5-139 Driver Monitoring Camera
*..........
........................................ 5-139
High Beam Control System
(HBC).................................. 5-140 High Beam Control System
(HBC)
*.............................. 5-140
Warnings and Cautions for Using
the High Beam Control System
(HBC)............................... 5-141
How to Use the High Beam
Control System (HBC)........ 5-142
Lane Departure Warning System
(LDWS)................................ 5-144 Lane Departure Warning System
(LDWS)
*............................ 5-144
Warnings and Cautions for Using
the Lane Departure Warning
System (LDWS).................. 5-144
How to Use the Lane Departure
Warning System (LDWS)..... 5-145
Blind Spot Monitoring (BSM).. 5-146
Blind Spot Monitoring (BSM)
*......
........................................ 5-146
Warnings and Cautions for Using
the Blind Spot Monitoring
(BSM)............................... 5-146
How to Use the Blind Spot
Monitoring (BSM).............. 5-147
Traffic Sign Recognition System
(TSR)................................... 5-150 Traffic Sign Recognition System
(TSR)
*................................5-150
Warnings and Cautions for Using
the Traffic Sign Recognition
System (TSR)..................... 5-150
How to Use the Traffic Sign
Recognition System (TSR)... 5-151
Convenient Ways to Use the
Traffic Sign Recognition
System (TSR)..................... 5-152
Distance & Speed Alert (DSA) ..........
.......................................... 5-153 Distance & Speed Alert (DSA)
*.....
........................................ 5-153
Warnings and Cautions for Using
the Distance & Speed Alert
(DSA)............................... 5-153
How to Use the Distance &
Speed Alert (DSA)............. 5-154
Driver Attention Alert (DAA)...5-155 Driver Attention Alert (DAA)
*.......
........................................ 5-155
Warnings and Cautions for Using
the Driver Attention Alert
(DAA)............................... 5-155
*Some models.5-5
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04