service MAZDA CX90 2024 Owner's Manual

Dealing with the Cause
If trouble arises while charging such as
not being able to charge the high
voltage battery, refer to the following
table. If the problem cannot be solved
even after checking the following table,
there may be a problem with the
vehicle or charger. Contact an
Authorized Mazda Dealer.
Charging is not possible.
CauseAction
The selector
lever is in a
position
other than P. Shift the selector lever to the P
position.
The high
voltage bat-
tery is al-
ready fully
charged. Charging is not performed when
the high voltage battery is al-
ready fully charged.
The high
voltage bat-
tery temper-
ature is ex-
tremely high
or low. Check the high voltage battery
temperature gauge in the instru-
ment cluster. If the high voltage
battery temperature gauge is in
the red or blue range, charging
may not be possible.
The
Lead-acid
battery is
depleted. If the instrument cluster does not
turn on even if the vehicle power
is switched ON, the Lead-acid
battery may be depleted. Charge
or replace the Lead-acid battery.
Normal charging is not possible.
Cause
Action
The outlet
has no pow-
er. Check if a ground-fault circuit in-
terrupter has operated or if a
power outage occurred. If the
power source has a timer func-
tion, electrical power may not be
supplied to the outlet until the
time set to supply power.
Cause
Action
The charge
plug is not
properly
plugged into
the outlet. Check if the charge plug is prop-
erly plugged into the outlet.
The charge
connector is
not properly
connected. Check if the charge connector is
properly connected.
Charging
timer is set. Cancel the charging timer using
EV Settings in Mazda Connect,
or the charging timer cancella-
tion function.
Troubleshooting for functions using a
Smartphone or computer
If you are having trouble with the
remote function service, such as when
the remote function does not work,
consult an Authorized Mazda Dealer.
What to Do in Case of Emergency
Charging Is Not Possible
8-16
CX-90_8KG7-EA-22L_Edition1_new
2022-11-17 16:05:04

Inspection and Servicing
Be careful not to hurt yourself when
inspecting your vehicle, replacing a
tire, or doing some kind of
maintenance such as changing the oil
and filter.
In particular, wear thick work gloves
such as cotton gloves when touching
areas that are difficult to see while
inspecting or working on your vehicle.
Doing inspections or procedures with
your bare hands could cause injury.

If you are unsure about any procedure
this manual describes, we strongly urge
you to have a reliable and qualified
service shop perform the work,
preferably an Authorized Mazda
Dealer.

Factory-trained Mazda technicians and
genuine Mazda parts are best for your
vehicle. Without this expertise and the
parts that have been designed and
made especially for your Mazda,
inadequate, incomplete, and
insufficient servicing may result in
problems. This could lead to vehicle
damage or an accident and injuries.

For expert advice and quality service,
consult an Authorized Mazda Dealer.

To continue warranty eligibility and to
protect your investment, it is your
responsibility to properly maintain your
vehicle according to factory
recommended schedules outlined in
this manual. As part of this you must
keep your maintenance records,
receipts, repair orders and any other
documents as evidence this
maintenance was performed. You must
present these documents, should any
warranty coverage disagreement occur.
Failure to do so can result in your
warranty being voided either in whole
or in part.

This evidence may consist of the
following:
The Mazda Scheduled Maintenance
Record, refer to the Warranty
Booklet, must be completely filled
out showing mileage, repair order
number, date for each service, and
signed by a qualified automotive
service technician who service
vehicles.
Original copies of repair orders or
other receipts that include the
mileage and date the vehicle was
serviced. Each receipt should be
signed by a qualified automotive
service technician.
For self maintenance, a statement
that you completed the maintenance
yourself, displaying mileage and the
date the work was performed. Also,
receipts for the replacement parts (fluid, filters, etc.) indicating the date
and mileage must accompany this
statement.

NOTE
If you elect to perform maintenance
yourself or have your vehicle serviced
at a location other than an Authorized
Mazda Dealer, Mazda requires that all
fluids, parts and materials must meet
Mazda standards for durability and
performance as described in this
manual.

Inspection and Servicing/Cleaning
Inspection and Servicing
9-2
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Maintenance ItemNumber of times, maintenance was performed.
12345678
Disc brakes IIIIIIII
Steering operation and linkages II II
Front and rear suspension, ball joints and
wheel bearing axial play IIII
Body condition inspection for
rust, corrosion and perfora-
tion Canada IIIIIIII
Driveshaft dust boot II II
Bolts and nuts on chassis and body TTT T
Cabin air filter Replace every 48,000 km (30,000 miles) or 24 months.
Tire rotation Rotate every 12,000 km (7,500 miles).
Tire inflation pressure and tire wear
*4Inspect every 12,000 km ( 7,500 miles) or 12 months.
Emergency flat tire repair kit (if equipped)
*5Inspect annually.
Function of all lights IIIIIIII
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust, fill up, or replace if necessary.
R: Replace
T: Tighten
Remarks:
*1 Reset the engine oil data whenever replacing the engine oil regardless of the message/wrench indicator light display.
*2 According to state/provincial and federal regulations, failure to perform maintenance on these itemswill not void your emissions warranties. However, Mazda recommends that all maintenance services
be performed at the recommended time or mileage/kilometer period to ensure long-term reliability.
*3 Use of FL-22 is recommended when replacing coolant. Using coolant other than FL-22 may causeserious damage to the engine and cooling system.
*4 Inspect a spare tire if equipped.*5 Check the tire repair fluid expiration date every year when performing the periodic maintenance.Replace the tire repair fluid bottle with new one before the expiration date.
Inspection and Servicing/Cleaning
Scheduled Maintenance
9-5
CX-90_8KG7-EA-22L_Edition1_new
2022-11-17 16:05:04

Daily Inspection
The owner or a qualified service
technician should make these vehicle
inspections at the indicated intervals to
ensure safe and dependable
operation.

Bring any problem to the attention of
an Authorized Mazda Dealer or
qualified service technician as soon as
possible.
When Refueling
Brake fluid level (page 9-16)Coolant level (page 9-14)Engine oil level (page 9-13)Washer fluid level (page 9-17)
At Least Monthly
Tire inflation pressures (page 9-27)
At Least Twice a Year (For Example,
Every Spring and Fall)
You can do the following scheduled
maintenance items if you have some
mechanical ability and a few basic
tools and if you closely follow the
directions in this manual.
Coolant (page 9-14)Engine oil (page 9-13)

Improper or incomplete service may
result in problems. This section gives
instructions only for items that are easy
to perform.

As explained in the Inspection and
Servicing section (page 9-2), several
procedures can be done only by a
qualified service technician with
special tools.

Improper owner maintenance during
the warranty period may affect
warranty coverage. Refer to the
Inspection and Servicing section (page
9-2) for owner's responsibility in
protecting your investment. For details,
read the separate Mazda Warranty
statement provided with the vehicle. If
you are unsure about any servicing or
maintenance procedure, have it done
by an Authorized Mazda Dealer.

There are strict environmental laws
regarding the disposal of waste oil and
fluids. Please dispose of your waste
properly and with due regard to the
environment.

We recommend that you entrust the oil
and fluid changes of your vehicle to an
Authorized Mazda Dealer.
Inspection and Servicing/Cleaning
Daily Inspection
9-7
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Inspecting Engine Oil
CAUTION
Do not overfill the engine oil. This may
cause engine damage.

Use center display screen indication to
inspect the engine oil level.
1. Make sure the hood is closed.
2. Start the hybrid system.
3. Select “Information” on the Home screen to display the vehicle status
monitor.
4. Select “Vehicle Status Monitor”.
5. Select “Engine Oil Level”.
6. Select “Start”. The engine starts and measurement
of the engine oil level begins. Do
not depress the accelerator pedal
during the measurement.
NOTE
If measurement conditions not
shown on the display are not met
such as when warm-up operation
has not been completed due to low
outdoor temperatures, the
measurement error screen may be
displayed. In this case, drive the
vehicle using the engine for a
certain period of time to complete
the warm-up operation and repeat
the procedure.

7. Switch the vehicle power OFF.
NOTE
After the measurement is
completed, the engine does not
stop automatically.

Recommended Oil
Use SAE 0W-20 engine oil.
Mazda Genuine Oil is used in your
Mazda vehicle. Mazda Genuine
0W-20 Oil is required to achieve
optimum fuel economy.
For maintenance service, Mazda
recommends Genuine Mazda Parts
and Genuine Mazda Premium Oil.

Only use SAE 0W-20 oil “Certified For
Gasoline Engines” by the American
Petroleum Institute (API).
Oil with this trademark symbol
conforms to the current engine and
emission system protection standards
and fuel economy requirements of the
International Lubricant Standardization
and Approval Committee (ILSAC),
Inspection and Servicing/Cleaning
Engine Compartment Inspection
9-13
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

3.

Installing the Hole Cover
1. Insert the hole cover into the cowlgrille.
Make sure that the hole cover holds
the cowl grille and the knobs are in
the correct position.
1. The hole cover
2. The cowl grille
2.

Removing the Lead-acid Battery Cover

Maintaining Lead-acid Battery
To get the best service from a lead-acid
battery:
Keep it securely mounted.Keep the top clean and dry.Keep terminals and connections
clean, tight, and coated with
petroleum jelly or terminal grease.
Rinse off spilled electrolyte
immediately with a solution of water
and baking soda.
Inspection and Servicing/Cleaning
Engine Compartment Inspection
9-20
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Contamination of either the
windshield or the blades with foreign
matter can reduce wiper effectiveness.
Common sources are insects, tree sap,
and hot wax treatments used by some
commercial car washes.
If the blades are not wiping properly,
clean the window and blades with a
good cleaner or mild detergent; then
rinse thoroughly with clean water.
Repeat if necessary.
NOTE
You can replace the wiper blades
yourself, however you cannot replace
the wiper arms.
If you want to replace the wiper arms,
consult an Authorized Mazda Dealer.

Replacing Front Windshield Wiper
Blade rubbers
1. Move the wipers to the servicepositions using the following
procedure.
a) Switch the vehicle power ON.
b) Switch the vehicle power OFF.
c) Press up the wiper switch to theMIST position 2 times within 30
seconds after switching the
vehicle power OFF.
When the procedure is
completed, the wipers operate
and they stop at the service
positions.
2. Raise the wiper arms.
3. Slide the blade component in the direction of the arrow while
pressing the wiper arm tab to
remove the blade component from
the wiper arm.
4.
Inspection and Servicing/Cleaning
Vehicle Exterior Inspection
9-24
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Exterior Maintenance
WARNING
Dry off brakes that have become wet
by driving slowly, releasing the
accelerator pedal and lightly applying
the brakes several times until the
brake performance returns to normal.
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected.
CAUTION
Before lifting the windshield wiper
blades off the windshield, always
follow the procedure for moving the
windshield wiper blades. Otherwise,
a wiper blade, wiper arm, or the
hood could be damaged.
Refer to the Replacing Windshield
Wiper Blade Rubbers section (page
9-23) for the procedure on how to
move the windshield wiper blades to
the service position.
 When the vehicle power is switched
ON and the wiper lever is in the
AUTO position, the windshield
wipers may operate automatically in
the following cases:
The area of the windshield above the
rain sensor is touched or wiped with
a cloth.
The windshield or the rain sensor
area in the cabin is hit.
When the vehicle power is switched
ON and the wiper lever is in the
AUTO position, do not touch the
windshield or the windshield wipers
Otherwise, the windshield wipers
will operate automatically which
could catch your fingers or damage
the windshield wipers.
When removing ice or snow, or
cleaning the windshield, always
make sure the wiper lever is in the
OFF position.
 Do not spray water in the engine
compartment. Otherwise, it could
result in engine-starting problems or
damage to electrical parts.
 When washing and waxing the
vehicle, be careful not to apply
excessive force to any single area of
the vehicle roof. Otherwise, you
could dent the vehicle.
 Make sure that the fuel-filler lid is
closed and lock the doors.
Otherwise, the fuel-filler lid may be
forcefully opened by water pressure
causing damage to the vehicle or
fuel-filler lid.
 (Vehicles with hands-free liftgate)
When washing or waxing the vehicle,
turn off the hands-free liftgate using
the Mazda Connect or do not bring
the transmitter into the area around
the liftgate. Otherwise, the liftgate
could open unexpectedly resulting in
an accident. Refer to Power Liftgate
section (page 4-21).
 Do not use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or caustic
agents on chrome-plated or
anodized aluminum parts. This may
damage the protective coating; also,
cleaners and detergents may discolor
or deteriorate the paint.
Inspection and Servicing/Cleaning
Exterior Maintenance
9-35
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Customer Assistance
Your complete and permanent
satisfaction is our business. We are
here to serve you. All Authorized
Mazda Dealers have the knowledge
and the tools to keep your Mazda
vehicle in top condition.
If you have any questions or
recommendations for improvement
regarding the service of your Mazda
vehicle or servicing by Mazda Dealer
personnel, we recommend that you
take the following steps:
NOTE
If it becomes necessary to have the
components or wiring system for the
supplementary restraint system
modified to accommodate a person
with certain medical conditions in
accordance with a certified physician,
contact an Authorized Mazda Dealer.
For more informatio n, go to NHTSA
website www.safercar.gov (VEHICLE
SHOPPERS > Air Bags > Air Bag FAQs >
Air Bag Deactivation).
STEP 1: Contact Your
Mazda Dealer
Discuss the matter with an Authorized
Mazda Dealer. This is the quickest and
best way to address the issue.
If your concern has not been
resolved by the CUSTOMER
RELATIONS, SALES, SERVICE, or
PARTS MANAGER, then please
contact the GENERAL MANAGER of
the dealership or the OWNER.
If it becomes necessary to have the
components or wiring system for the
supplementary restraint systemmodified to accommodate a person
with certain medical conditions in
accordance with a certified
physician, go to STEP 2.
Specifications/Customer Information and Reporting Safety Defects
Customer Assistance (U.S.A.)
10-4
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

7. California Civil Code Section1793.2 (d) requires that, if Mazda
or its representative is unable to
repair a new motor vehicle to
conform to the vehicle's applicable
express warranty after a reasonable
number of attempts, Mazda may be
required to replace or repurchase
the vehicle. California Civil Code
Section 1793.22 (b) creates a
presumption that Mazda has had a
reasonable number of attempts to
conform the vehicle to its
applicable express warranties if,
within 18 months from delivery to
the buyer or 18,000 miles on the
vehicle's odometer, whichever
occurs first, one or more of the
following occurs:
The same nonconformity [a
failure to conform to the written
warranty that substantially impairs
the use, value or safety of the
vehicle] results in a condition that
is likely to cause death or serious
bodily injury if the vehicle is
driven AND the nonconformity
has been subject to repair two or
more times by Mazda or its
agents AND the buyer or lessee
has directly notified Mazda of the
need for the repair of the
nonconformity; OR
The same nonconformity has
been subject to repair 4 or more
times by Mazda or its agents
AND the buyer has
notified
Mazda of the need for the repair
of the nonconformity; OR
The vehicle is out of service by
reason of repair of
nonconformities by Mazda or its
agents for a cumulative total of
more than 30 calendar days after
delivery of the vehicle to the
buyer.

NOTICE TO Mazda AS REQUIRED
ABOVE SHALL BE SENT TO THE
FOLLOWING ADDRESS:
Mazda North American Operations
200 Spectrum Center Drive Suite
100
Irvine, California 92618
ATTN: Customer Mediation

8. The following remedies may be sought in BBB AUTO LINE: repairs,
reimbursement for money paid to
repair a vehicle or other expenses
incurred as result of a vehicle
nonconformity, repurchase or
replacement of your vehicle, and
compensation for damages and
remedies available under Mazda's
written warranty or applicable law.
9. The following remedies may not be
sought in BBB AUTO LINE: punitive
or multiple damages, attorneys'
fees, or consequential damages
other than as provided in California
Civil Code Section 1794 (a) and
(b).
10.You may reject the decision issued by a BBB AUTO LINE arbitrator. If
you reject the decision, you will be
free to pursue further legal action.
The arbitrator's decision and any
findings will be admissible in a
court action.
11.If you accept the arbitrator's decision, Mazda will be bound by
the decision, and will comply with
the decision within a reasonable
time not to exceed 30 days after we
receive notice of your acceptance
of the decision.
12.Please call BBB AUTO LINE at 1-800-955-5100 for further details
about the program.
Specifications/Customer Information and Reporting Safety Defects
Customer Assistance (U.S.A.)
10-8
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04