wheel MAZDA MIATA 1991 Factory User Guide

Disconnect 2-pin connector at hydraulic unit. Check continuity at hydraulic control between Red/Yellow wire
terminal and ground. If continuity is not present, replace hydraulic control unit. If continuity is present, pump is
okay. Check wiring between hydraulic control and ABS control unit.
Continuity Test (RX7 & 929)
1. Disconnect 12-pin hydraulic unit connector. Using a DVOM, check continuity between Black wire and
ground. If there is continuity, check continuity between Black wire terminal at hydraulic unit connector
and Green wire terminal at 2-pin hydraulic unit connector.
2. If continuity exists, connect hydraulic unit connectors. If continuity is not present, replace wiring harness
between control unit and body ground.
3. Disconnect ABS control unit connector. Check continuity between Green wire of ABS control unit
harness connector and ground. If continuity is present, check for poor connection of ABS control unit
connector or faulty ABS control unit. If continuity is not present, repair open circuit.
VALVE RELAY
Continuity Tests
1. Disconnect negative battery cable. Remove valve relay from hydraulic unit. Using a DVOM, check
continuity between relay terminals "C" and "E" and between terminals "B" and "D". See Fig. 11
.
2. Ensure continuity exists. Connect 12 volts to terminal "B", and ground terminal "D". Check continuity
between terminals "A" and "E". Ensure continuity exists. If continuity is not as specified, replace valve
relay.
WHEEL SPEED SENSORS
Sensor Resistance Test
Disconnect speed sensor connector. Using a DVOM, measure resistance between sensor terminals. Resistance
should be 800-1200 ohms. If resistance is not as specified, replace speed sensor.
Harness Continuity & Voltage Tests
1. With ignition off and speed sensors connected, disconnect ABS control unit connector. Using a DVOM,
check continuity between indicated terminals of ABS control unit harness connector. See WHEEL
SPEED SENSOR TESTS TABLE.
2. If reading on DVOM is not 800-1200 ohms, check wiring harness between wheel speed sensor and ABS
control unit. If DVOM reading is 800-1200 ohms, check voltage between indicated terminals in WHEEL
SPEED SENSOR TESTS TABLE.
3. Turn ignition on. Rotate appropriate wheel one revolution per second by hand to check voltage. If DVOM
does not indicate 50-60 millivolts, replace wheel speed sensor.
WHEEL SPEED SENSOR TESTS
Test Between Control Unit

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:32 PMPage 13 © 2005 Mitchell Repair Information Company, LLC.

WHEEL SPEED SENSOR ROTORS
Inspection
Perform a comprehensive visual inspection of sensor rotor. If any damage is noted, replace sensor rotor. Sensor
rotors are attached to wheel hubs.
REMOVAL & INSTALLATION
HYDRAULIC UNIT
Removal
Remove hydraulic lines from unit. Disconnect hydraulic unit connectors. Remove nuts securing unit. Remove
hydraulic unit.
Bleeding Hydraulic Unit
Before bleeding hydraulic unit, bleed brake system in appropriate sequence. See BRAKE LINE BLEEDING
SEQUENCE TABLE under BLEEDING BRAKE SYSTEM. Bleed hydraulic unit by opening bleeder screw on
unit. See Fig. 12
.
Installation
To install, reverse removal procedure. Tighten mounting bolts to specification. See TORQUE
ApplicationConnector Terminals (1)
Miata
Left Front"K" & "G"
Left Rear"O" & "Q"
Right Front"U" & "F"
Right Rear"L" & "P"
RX7
Left Front"D" & "F"
Left Rear"H" & "I"
Right Front"U" & "W"
Right Rear"X" & "Z"
929
Left Front"K" & "G"
Left Rear"O" & "Q"
Right Front"J" & "F"
Right Rear"L" & "P"
(1)See Fig. 4 or Fig. 5 to identify ABS control unit terminals.

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:32 PMPage 14 © 2005 Mitchell Repair Information Company, LLC.

SPECIFICATIONS TABLE at end of article.
Fig. 12: Locating Hydraulic Unit Bleeder Screw

Courtesy of MAZDA MOTORS CORP.
WHEEL SPEED SENSOR ROTOR
Removal (Miata)
Remove brake caliper. Remove wheel hub. On rear axle, carefully remove sensor rotor from axle using a chisel.
On front rotor, remove sensor rotor using Puller (49- 0839-425C).
Installation
Press sensor rotor onto axle using Installer (49- H026-101A). Install sensor rotor on front rotor with chamfered
edge toward hub using Press Adapter (49-F001-95). To complete installation, reverse removal procedure.
Tighten mounting bolts to specification. See TORQUE SPECIFICATIONS TABLE at end of article.
Removal & Installation (RX7)
Remove brake caliper and wheel hub. On rear hub, remove wheel hub from outer toe control hub using Puller
(49-F026-103) and Installer (49-F026-102). On front rotor, remove rotor-to-hub bolts using Allen wrench. On
rear rotor, remove rotor-to-hub screws. To install, reverse removal procedure. Tighten mounting bolts to
specification. See TORQUE SPECIFICATIONS TABLE at end of article.
Removal & Installation (929)

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:32 PMPage 15 © 2005 Mitchell Repair Information Company, LLC.

Remove brake caliper and wheel hub. On rear axle, carefully remove sensor rotor from axle using chisel. On
front rotor, remove sensor rotor using Puller (49-0839-425C). To install, press sensor rotors onto axle and front
rotor using Installer (49-H026-101A). On front rotor, install sensor rotor with chamfered edge toward hub. To
complete installation, reverse removal procedure. Tighten mounting bolts to specification. See TORQUE
SPECIFICATIONS TABLE at end of article.
WHEEL SPEED SENSOR
Removal & Installation
Unplug wheel sensor connector. Remove sensor bolt. Remove wheel sensor from vehicle. To install, reverse
removal procedure. On RX7, adjust wheel sensor so clearance between sensor and rotor is .016-.039" (.40-1.0
mm). Tighten mounting bolts to specification. See TORQUE SPECIFICATIONS TABLE at end of article.
DIAGNOSING ABS SYSTEM
ABS TESTER OPERATION
Fig. 13: Operating ABS Tester

Courtesy of MAZDA MOTORS CORP.
TESTING SEQUENCE

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:32 PMPage 16 © 2005 Mitchell Repair Information Company, LLC.

Courtesy of MAZDA MOTORS CORP.
6A. DYNAMIC WHEEL SELECTION TEST OR EXIT
WHEEL SELECTION TEST
These three messages will alternate on the dispaly screen at 3 1/2 second intervals. Now, select one of the four
wheels to begin the dynamic test sequence.
EXIT
Press either switch under "PUSH TO EXIT" Display to return to "STAT TEST DYNAM" Selection.
NOTE: When entering the dynamic test sequence, you will select one of four wheels to
begin. When you have finished with that wheel test, you should return to 6A.
WHEEL SELECTION TEST to select another wheel, and repeat these test
procedures for all four wheels

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:32 PMPage 23 © 2005 Mitchell Repair Information Company, LLC.

Fig. 20: 6A. Dynamic Wheel Selection Test
Courtesy of MAZDA MOTORS CORP.
6B. DYNAMIC WHEEL SENSOR TEST

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:32 PMPage 24 © 2005 Mitchell Repair Information Company, LLC.

Fig. 21: 6B. Dynamic Wheel Sensor Test (1 of 2)
Courtesy of MAZDA MOTORS CORP.

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:32 PMPage 25 © 2005 Mitchell Repair Information Company, LLC.

Fig. 22: 6B. Dynamic Wheel Sensor Test (2 of 2)
Courtesy of MAZDA MOTORS CORP.
6C. SOLENOID TEST

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:32 PMPage 26 © 2005 Mitchell Repair Information Company, LLC.

WIRING DIAGRAMS
Rear12-17 (16-23)
Brake Line Nuts10-16 (14-22)
Hydraulic Unit Mounting Nuts
Miata & 92914-19 (19-26)
RX712-21 (16-28)
Speed Sensor Bolt12-17 (16-23)
Union Bolt14-22 (19-30)
Wheel Bearing Nut (1)
Miata
Front123-159 (167-216)
Rear159-217 (216-294)
RX7
Front(1) 14-22 (19-30)
Rear174-231 (235-314)
929
Front72-130 (98-176)
Rear174-231 (235-314)
(1)Tighten and loosen 2 or 3 times to seat bearing.

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:32 PMPage 32 © 2005 Mitchell Repair Information Company, LLC.

1990-93 DRIVE AXLES
Axle Shafts - MX-5 Miata
DESCRIPTION
The axle shaft is a double offset, constant velocity joint type.
TROUBLE SHOOTING
Check dust boot on axle shaft for cracks, damage, leaking grease, and loose boot bands. Check axle shaft for
bending, cracks, and wear of joints or splines. Repair or replace axle shaft if necessary.
REMOVAL & INSTALLATION
AXLE SHAFTS
Removal
1. Raise vehicle and support with safety stands. Remove wheel and tire assembly. See Fig. 1 . Loosen axle
shaft lock nut until flush with end of axle shaft. Mark differential and axle shaft flanges for installation
reference. See Fig. 2
. Remove axle shaft flange nuts. NOTE: See TROUBLE SHOOTING
- BASIC PROCEDURES article in GENERAL
INFORMATION.
NOTE: Manufacturer recommends using new axle shaft lock nut during
installation.

1991 Mazda MX-5 Miata
1990-93 DRIVE AXLES Axle Shafts - MX-5 Miata

1991 Mazda MX-5 Miata
1990-93 DRIVE AXLES Axle Shafts - MX-5 Miata
Microsoft
Sunday, July 05, 2009 2:16:32 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.
Microsoft
Sunday, July 05, 2009 2:16:36 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.