glove box MAZDA MIATA 1991 Factory Service Manual

BLOWER MOTOR
Disconnect 2-wire connector from bottom of blower motor case. Apply battery voltage across blower motor
terminals. Replace blower motor if it does not operate.
BLOWER RESISTOR
Note 4-wire connector and 1-wire connector attached to seam where upper and lower blower cases meet. Wires
in these connectors lead to blower resistor on bottom of blower case. Disconnect both connectors. If continuity
does not exist between 1-wire connector terminal and each terminal of 4-wire connector, replace blower
resistor.
CONDENSER (ADDITIONAL) FAN MOTOR
Disconnect condenser fan connector. Apply battery voltage across condenser fan terminals. Replace condenser
fan motor if it does not operate.
EVAPORATOR THERMOSWITCH
1. Remove glove box. Run engine at idle. Turn off A/C switch. Turn blower switch to 4th position (high) for
a few minutes to ensure evaporator temperature is greater than 32°F (0°C). Turn off blower switch and
engine.
2. Disconnect evaporator thermoswitch connector. Check continuity between switch terminals. If there is
continuity, thermoswitch is okay. If there is no continuity, replace thermoswitch.
PRESSURE SWITCH
1. Turn ignition off. Connect manifold pressure gauges to system. If high-side pressure is less than 31.2 psi
(2.2 kg/cm
2 ), check system for proper refrigerant charge.
2. If high-side pressure is greater than 31.2 psi (2.2 kg/cm
2 ), disconnect pressure switch connector. Check
continuity between switch terminals. If there is continuity, switch is okay. If there is no continuity,
replace switch.
REMOVAL & INSTALLATION
AIR BAG WARNING
BLOWER CASE
Removal & Installation
WARNING:To avoid injury from accidental air bag deployment, read and carefully
follow all SERVICE PRECAUTIONS and DISABLING & ACTIVATING AIR
BAG SYSTEM procedures in AIR BAG article in the
ACCESSORIES/SAFETY EQUIPMENT Section.

1991 Mazda MX-5 Miata
A/C-HEATER SYSTEM - MANUAL 1990-92 Manual A/C-Heater Systems
Microsoft
Sunday, July 05, 2009 2:11:52 PMPage 6 © 2005 Mitchell Repair Information Company, LLC.

Disconnect electrical connectors from blower case. Remove glove box. Loosen seal plate between blower motor
case and evaporator case. Remove blower motor case nuts. Remove case and seal plate. To install, reverse
removal procedure.
COMPRESSOR
Removal & Installation
1. Disconnect negative battery cable. Discharge A/C system using approved refrigerant recovery/recycling
equipment. Disconnect compressor clutch connector. Disconnect refrigerant lines from compressor.
Remove drive belt.
2. Raise and support vehicle. Remove compressor mounting bolts and remove compressor. To install,
reverse removal procedure. Adjust drive belt to specified tension. Evacuate and charge system.
CONDENSER & RECEIVER-DRIER
Removal & Installation
Discharge A/C system using approved refrigerant recovery/recycling equipment. Raise and support vehicle.
Remove splash shield and air guide. Remove condenser and receiver-drier as an assembly. To install, reverse
removal procedure. Evacuate and charge system.
CONTROL PANEL
Removal & Installation
Remove rear console assembly. See Fig. 4 . Remove vent outlets from center panel assembly. Remove center
panel assembly. Remove control panel screws. Pull control panel from hole. Disconnect door control cables
from back of control panel and remove panel. To install, reverse removal procedure.
EVAPORATOR CORE & THERMOSWITCH
Removal & Installation
1. Discharge A/C system using approved refrigerant recovery/recycling equipment. Remove condenser and
receiver-drier as an assembly. Disconnect low-pressure and high-pressure pipes from evaporator tubes at
engine compartment firewall.
2. Remove right undercover and glove box. Disconnect thermoswitch electrical connector. Loosen left seal
plate (between heater case and evaporator case). Loosen right seal plate (between evaporator case and
blower motor case).
3. Remove evaporator case. Disassemble evaporator case, and remove evaporator core and thermoswitch.
See Fig. 3
. To install, reverse removal procedure. Evacuate and charge system.

1991 Mazda MX-5 Miata
A/C-HEATER SYSTEM - MANUAL 1990-92 Manual A/C-Heater Systems
Microsoft
Sunday, July 05, 2009 2:11:52 PMPage 7 © 2005 Mitchell Repair Information Company, LLC.