MAZDA MODEL 3 4-DOOR 2004 Owners Manual

6-13
Interior Comfort
Au di o S ys t em
Form No. 8S18-EA-03I

Operating Tips for Cassette Tape
Player
Cleaning the cassette tape player
The tape head, capstans, and pinch rollers
will gather oxide residue from cassette
tapes. This can cause weak or wavering
sounds and damage to the cassette tapes
and player. Use a good quality head-
cleaning tape or a liquid cleaner cassette
tape to remove it.
Should the unit not operate normally,
consult an Authorized Mazda Dealer.
Never attempt to repair it or insert a
screwdriver or anything else.
Handling the cassette tape player
The following precautions should be
observed.
• Do not spill any liquid on the audio
system.
• Do not insert any objects, other than
cassette tape, into the slot. •
If the cassette tape is loose, it may
produce poor sound or performance
during playback. Use a pencil or
something similar to remove any slack.
• Only cassette tapes that play no longer
than 90 minutes should be used.
Cassette tape exceeding 90 minutes are
thin and may easily break.
• Do not leave a cassette tape in the tape
player slot when not in use. Remove it
completely to permit the slot door to
close and to protect the mechanism
from dust.
• Store cassette tapes away from extreme
heat, magnetic fields, and direct
sunlight. Protect the exposed cassette
tape from dirt and damage. Store
cassette tapes in their original cases or
other protective cases.
J48C_8S18-EA-03I_Edition3.book Page 13 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

6-14
Interior Comfort
Au di o S ys t em
Form No. 8S18-EA-03I

Operating Tips for Mini Disc
(MD) Player
The following precautions should be
observed.
• Do not spill any liquid on the audio
system.
• Do not insert any objects, other than
MDs, into the slot.
• The MD player has been designed to
play MDs bearing the identification
logo as shown. No other MDs can be
played. •
The MD player can also play MDLPs
that have been recorded in MDLP
mode. (MDLPs bearing the
identification logo as shown below).
• When inserting the MD, make sure the
MD label is facing up, and the MD is
oriented to the insertion slot in the
direction of the arrow. If not inserted
correctly, the MD will be ejected, or
may remain stuck in the MD deck.
• Do not touch the internal part of the
MD. If the MD shutter is slid open for
no reason, it may be broken.
• Store MDs in their cases and away
from direct sunlight.
J48C_8S18-EA-03I_Edition3.book Page 14 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

6-15
Interior Comfort
Au di o S ys t em
Form No. 8S18-EA-03I

Operating Tips for CD Player/In-
Dash CD Changer
Condensation phenomenon
Immediately after turning on the heater
when the vehicle is cold, the CD or optical
components (prism and lens) in the CD
player/changer may become clouded with
condensation. At this time, the CD will
eject immediately when placed in the unit.
A clouded CD can be corrected simply by
wiping it with a soft cloth. Clouded
optical components will clear naturally in
about an hour. Wait for normal operation
to return before attempting to use the unit.
Handling the CD player/In-dash CD
changer
The following precautions should be
observed.
• Do not spill any liquid on the audio
system.
• Do not insert any objects, other than
CDs, into the slot. •
The CD revolves at high speed within
the unit. Defective (cracked or badly
bent) CDs should never be used.
• Do not use non-conventional discs such
as heart-shaped, octagonal discs, etc.
The CD player/changer could be
damaged.
•
A new CD may have rough edges on its
inner and outer perimeters. If a disc
with rough edges is used, proper setting
will not be possible and the CD player/
changer will not play the CD. Remove
the rough edges in advance by using a
ball-point pen or pencil as shown
below. To remove the rough edges, rub
the side of the pen or pencil against the
inner and outer perimeter of the CD.
J48C_8S18-EA-03I_Edition3.book Page 15 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

6-16
Interior Comfort
Au di o S ys t em
Form No. 8S18-EA-03I
•When driving over uneven surfaces, the
sound may jump.
• The CD player/changer has been
designed to play CDs bearing the
identification logo as shown. No other
discs can be played.
• Be sure never to touch the signal
surface when handling the CDs. Pick
up a CD by grasping the outer edge or
the edge of the hole and the outer edge.
• Do not stick paper or tape on the CD.
Avoid scratching the reverse side (the
side without a label). •
Dust, finger smudges, and dirt can
decrease the amount of light reflected
from the signal surface, thus affecting
sound quality. If the CD should
become soiled, gently wipe it with a
soft cloth from the center of the CD to
the edge.
• Do not use record sprays, antistatic
agents, or household spray cleaners.
Volatile chemicals such as benzine and
thinner can also damage the surface of
the CD and must not be used. Anything
that can damage, warp, or fog plastic
should never be used to clean CDs.
• CDs, like traditional audio records, are
made of plastic. To avoid warping,
keep the CDs in their cases and do not
store them where they will be exposed
to direct sunlight.
• The CD player/changer ejects the CD if
the CD is inserted upside down. Also
dirty and/or defective CDs may be
ejected.
• 8 cm (3 in) CDs and CD accessories
(e.g. 8 cm disc adapter) cannot be used
in the CD player/changer.
• Do not insert cleaning discs in the CD
player/changer.
• Do not insert any disc with a peel-off
or seal on it.
J48C_8S18-EA-03I_Edition3.book Page 16 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

6-17
Interior Comfort
Au di o S ys t em
Form No. 8S18-EA-03I
Power/Volume/Sound Controls ......................................................................................6-18
Operating the Radio .......................................................................................................6-20
Operating the Cassette Tape Player* ..............................................................................6-22
Operating the Mini Disc (MD) Player* .........................................................................6-24
Operating the Compact Disc (CD) Player* ....................................................................6-26
Operating the In-Dash CD Changer* .............................................................................6-28
Error Indications .............................................................................................................6-31
Audio Set
CD Player* In-Dash CD Changer*
Cassette Tape Player* Mini Disc (MD) Player*
Illustration is of a representative audio unit.
Audio information is displayed on the information display.
*Some models.
J48C_8S18-EA-03I_Edition3.book Page 17 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

6-18
Interior Comfort
Au di o S ys t em
Form No. 8S18-EA-03I

Power/Volume/Sound Controls
Power ON/OFF
Turn the ignition switch to the ACC or
ON position.
Press the power/volume dial to turn the
audio system on.
Press the power/volume dial again to turn
the audio system off.
Volume adjustment
To adjust the volume, turn the power/
volume dial. Turn the power/volume dial to the right to
increase volume, to the left to decrease it.
Audio sound adjustment
1. Press the audio control dial to select the
function. The selected function will be
indicated.
*Depending on the mode selected, the indication changes.
Audio control dial
Power/Volume dial
NOTE
To prevent the battery from being
discharged, do not leave the audio
system on for a long period of time
when the engine is not running.
*
*
*
J48C_8S18-EA-03I_Edition3.book Page 18 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

6-19
Interior Comfort
Au di o S ys t em
Form No. 8S18-EA-03I
2. Turn the audio control dial to adjust the selected functions as follows: Automatic Level Control (ALC)
The automatic level control is a feature
that automatically adjusts audio volume
and sound quality according to the vehicle
speed.
The volume increases in accordance with
the increase in vehicle speed, and
decreases as vehicle speed decreases.
The following four modes are available.
Select the desired mode.
Turn the audio control dial to select the
ALC OFF, ALC LEVEL1
—3 mode. The
selected mode will be indicated.
BEEP setting
The beep-sound when operating the audio
system can be set on or off.
ILLM EFT setting (Illumination setting
during operation)
The audio system illumination during
operation can be set on or off.
Indication Turn Left Turn Right
Select
modeSelect
mode
Decrease
bass Increase
bass
Decrease
mid-
range Increase
mid-range
Decrease
treble Increase
treble
Shift the
sound
to the
front Shift the
sound
to the rear
Shift the
sound
to the left Shift the
sound
to the right
OFF ON
OFF ON
NOTE
About 5 seconds after selecting any
mode, the volume function will be
automatically selected. To reset bass,
mid-range, treble, fade, and balance,
press the audio control dial for 2
seconds. The unit will beep and
"CLEAR" will be displayed.
Mode Vo l u m e
change
No change
Minimum
Medium
Maximum
J48C_8S18-EA-03I_Edition3.book Page 19 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

6-20
Interior Comfort
Au di o S ys t em
Form No. 8S18-EA-03I

Operating the Radio
Radio ON
Press a band selector button ( , )
to turn the radio on.
Band selection
Choose AM by pressing the AM button
( ) and FM by pressing the FM1/2
button ( ).
The selected mode will be indicated. If
FM stereo is being received, "ST" will be
displayed. Tu n i n g
The radio has the following tuning
methods: Manual, Seek, Scan, Preset
channel, and Auto memory tuning. The
easiest way to tune stations is to set them
on preset channels.
Manual tuning
Turning the manual tuning dial will
change the frequency higher or lower.
Manual tuning dial/
Auto memory button
Channel
preset
buttons
Scan button
Band selector buttons
Seek
tuning
buttons
NOTE
If the FM broadcast signal becomes
weak, reception automatically changes
from STEREO to MONO for reduced
noise, and the "ST" indicator will go
out.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the preset channels will be canceled.
J48C_8S18-EA-03I_Edition3.book Page 20 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

6-21
Interior Comfort
Au di o S ys t em
Form No. 8S18-EA-03I
Seek tuning
Pressing the seek tuning button ( , )
will cause the tuner to seek a higher or
lower frequency automatically.
Scan tuning
Press the scan button ( ) to
automatically sample strong stations.
Scanning stops at each station for about 5
seconds. To hold a station, press the scan
button ( ) again during this interval.
Preset channel tuning
The 6 preset channels can be used to store
6 AM and 12 FM stations.
1. To set a channel first select AM, FM1, or FM2. Tune to the desired station.
2. Depress a channel preset button for about 2 seconds until a beep is heard.
The preset channel number and station
frequency will be displayed. The
station is now held in the memory.
3. Repeat this operation for the other stations and bands you want to store.
To tune one in the memory, select AM,
FM1, or FM2 and then press its
channel preset button. The station
frequency and the channel number will
be displayed. Auto memory tuning
This is especially useful when driving in
an area where the local stations are not
known. Additional AM/FM stations can
be stored without disturbing the
previously set channels.
Press and hold the auto memory button
( ) for about 2 seconds until a beep
is heard; the system will automatically
scan and temporarily store up to 6 stations
with the strongest frequencies in each
selected band in that area.
After scanning is completed, the station
with the strongest frequency will be tuned
and its frequency displayed.
Press and release the auto memory button
( ) to recall stations from the auto-
stored stations. One stored station will be
selected each time; its frequency and
channel number will be displayed.
NOTE
If you continue to press and hold the
button, the frequency will continue
changing without stopping.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the preset channels will be canceled.
NOTE
If no stations can be tuned after
scanning operations, "A" will be
displayed.
J48C_8S18-EA-03I_Edition3.book Page 21 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

6-22
Interior Comfort
Au di o S ys t em
Form No. 8S18-EA-03I

Operating the Cassette Tape Player*
Cassette tape insert
Insert the cassette tape into the slot, open
edge to the right and cassette tape will
begin play, and "TAPE PLAY" will be
displayed. At the end of the cassette tape,
the unit automatically reverses cassette
tape play. When is lit, the cassette
tape
’s top side is playing. When is lit,
the bottom side is on.
Playing
Press the cassette tape play button
( ) to start play when a cassette
tape is in the unit. If there isn ’t a cassette
tape in the unit when the cassette tape
play button ( ) is pressed, "NO
TAPE" will flash on and off. Dolby noise reduction
When using a tape with Dolby NR*, push
the Dolby NR button ( ). The
symbol will be displayed. To play a tape
without Dolby NR, push the button once
again.
*Noise reduction system manufactured
under license from Dolby Laboratories
Licensing Corporation.
Dolby and the double-D symbol are
trademarks of Dolby Laboratories
Licensing Corporation.
Ejecting the cassette tape
Press the cassette tape eject button ( ) to
eject the cassette tape.
Fast-forward
button
Rewind
button
APC button:
(next program)
(one being
played)
Cassette tape eject button
Cassette tape slot
Program button
Dolby NR buttonRepeat button
Cassette tape play button
*Some models.
J48C_8S18-EA-03I_Edition3.book Page 22 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI