lock MAZDA MODEL 3 4-DOOR 2005 Owners Manual

Black plate (284,1)
Brake lights/Taillights(5 Door)
With LED bulb
Due to the complexity and difficulty of
the procedure, the LED bulbs should be
replaced by an Authorized Mazda Dealer.
NOTE
LED bulb replacement is not possible.
The rear combination component must
be replaced.
With Non-LED bulb
1. Remove the cover.
Left side
Right side
2. Turn the socket and bulb assembly counterclockwise and remove it. 3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Rear turn signal lights (5 Door)
1. Remove the cover.
Left side
8-42
Maintenance and Care
Owner Maintenance
Mazda3_8T96-EA-04J_Edition3 Page284
Wednesday, May 11 2005 3:39 PM
Form No.8T96-EA-04J

Black plate (285,1)
Right side
2. Turn the socket and bulb assemblycounterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Reverse light
4 Door
1. Pull the center section of the plasticretainer and remove the retainers, then
remove the trunk rear trim.
Removal
Installation
2. Turn the socket and bulb assembly counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Maintenance and Care
Owner Maintenance
8-43
Mazda3_8T96-EA-04J_Edition3 Page285
Wednesday, May 11 2005 3:39 PM
Form No.8T96-EA-04J

Black plate (286,1)
5 Door
1. Remove the cover.
2. Turn the socket and bulb assemblycounterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
High-mount brake light
4 Door
1. Pull the center of each plastic retainer
and remove the retainers and the trunk
rear trim.
Removal
Installation
2. Disconnect the electrical connector from the socket.
3. Turn the socket and bulb assembly counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
8-44
Maintenance and Care
Owner Maintenance
Mazda3_8T96-EA-04J_Edition3 Page286
Wednesday, May 11 2005 3:39 PM
Form No.8T96-EA-04J

Black plate (287,1)
5 Door
1. Remove the liftgate upper trim.
2. Disconnect the electrical connectorfrom the socket.
3. Turn the socket and bulb assembly counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
License plate lights
1. Wrap a flathead screwdriver with a softcloth to prevent damage to the lens and
remove the lens by carefully prying on
the edge of the lens with a flathead
screwdriver.
2. Disconnect the bulb by pulling it out.
Edge
3. Install the new bulb in the reverse order of removal.
qReplacing Interior Light Bulbs
Overhead light/Map lights (Front)í
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the trim and
gently insert it in the overhead light as
shown in the figure, and then remove
the overhead light unit.
Maintenance and Care
Owner Maintenance
8-45íSome models.
Mazda3_8T96-EA-04J_Edition3 Page287
Wednesday, May 11 2005 3:39 PM
Form No.8T96-EA-04J

Black plate (288,1)
2. Turn the socket and bulb assemblycounterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order of removal.
Overhead light (Rear)
1. Wrap a small flathead screwdriver witha soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
flathead screwdriver.
2. Disconnect the bulb by pulling it out.
Edge
3. Install the new bulb in the reverse order of removal.
Trunk light (4 Door)
1. Press both sides of the lens cap toremove it.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order of removal.
Luggage compartment light (5 Door)
1. Insert your finger as shown in thefigure and remove the unit.
2. Wrap a small flathead screwdriver witha soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
flathead screwdriver.
8-46
Maintenance and Care
Owner Maintenance
Mazda3_8T96-EA-04J_Edition3 Page288
Wednesday, May 11 2005 3:39 PM
Form No.8T96-EA-04J

Black plate (290,1)
3. Turn the knobs counterclockwise andlower the fuse block.
4. Locate the position of the suspected
fuse by using the chart inside the fuse
block cover.
5. Pull the fuse straight out with the fuse puller provided on the inside of the
engine compartment fuse block cover.
6. Inspect it and replace if it's blown.
Normal Blown
7. Push in a new fuse of the same
amperage rating, and make sure it fits
tightly. If it doesn't, have an Authorized
Mazda Dealer install it.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the MIRROR or CIGAR circuit.
CAUTION
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Replacing the fuses under the hood
If the headlights or other electrical
components don't work and the fuses in
the cabin are OK, inspect the fuse block
under the hood. If a fuse is blown, it must
be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.
8-48
Maintenance and Care
Owner Maintenance
Mazda3_8T96-EA-04J_Edition3 Page290
Wednesday, May 11 2005 3:39 PM
Form No.8T96-EA-04J

Black plate (291,1)
2. Remove the fuse block cover.
3. If a fuse is blown, replace it with a newone of the same amperage rating .
Normal
Blown
NOTE
To replace the MAIN fuse, contact an
Authorized Mazda Dealer.
Maintenance and Care
Owner Maintenance
8-49
Mazda3_8T96-EA-04J_Edition3 Page291
Wednesday, May 11 2005 3:39 PM
Form No.8T96-EA-04J

Black plate (292,1)
qFuse Panel Description
Fuse block (Engine compartment)
12 3
4 5 6
789
10
11
12
13 1415 16 17 18
19 20 21
22
23
24
25
26
27
28
29
30 31
32
33
34
35
36
DESCRIP-
TIONFUSERAT-ING PROTECTED
COMPONENT
1 FAN 40 A Cooling fan
2 P/ST 80 A EHPAS
3 BTN 40 A For protection of various
circuits
4 HEAD 40 A Headlights
5 PTC 80 A ―
6 GLOW 60 A ―
7 ABS 1 30 A ABS
í
8 ABS 2 20 A ABSí
9ENGINE30 A For protection of various
circuits
10―― ―
11 IG KEY 130 A Ignition switch
12 STARTER20 A Starter clutch
13 IG KEY 230 A Ignition switch
14―― ―
DESCRIP-
TIONFUSERAT-ING PROTECTED
COMPONENT
15 HEATER40 A Blower motor
16―― ―
17DEFOG 40 A Rear window defroster
18AUDIO 30 A Audio system
(BOSE Sound System-equip-
ped model)
19ABS IG 10 A ABSí
20FOG 15 A Fog lightsí
21HORN 15 A Horn
22―― ―
23 H/CLEAN20 A
―
24 F/PUMP15 A Fuel pump
25P/ST IG 10 A Power steering
26 A/C MAG10 A Air conditioner
27ALT 10 A ―
28―― ―
8-50
Maintenance and Care
íSome models.
Owner Maintenance
Mazda3_8T96-EA-04J_Edition3 Page292
Wednesday, May 11 2005 3:39 PM
Form No.8T96-EA-04J

Black plate (294,1)
Fuse block (Passenger's side)
37 38 39 4041 42
43 44 45 46
47 48 49 50 51
52 53 54 55 56 57 58
59 60 61 62 63 64
65 66 67 68 69 70
71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86
DESCRIP-
TIONFUSERAT-ING PROTECTED
COMPONENT
37 D/LOCK 215 A Power door lock
38―― ―
39 HEAD
HIGH L10 A Headlight high beams (LH)
40 HEAD
HIGH R10 A Headlight high beams (RH)
41―― ―
42―― ―
43CIGAR 15 A Lighter
44RADIO 7.5 A Audio system
45 MIRROR10 A Power control mirror
46TAIL R 7.5 A Taillight (RH), Parking lights
(RH) License plate lights
47OBD 10 AFor protection of various
circuits
48―― ―
49 TR/LOCK20 A
―
50 CPU PWR10 A Control unit
DESCRIP-
TIONFUSERAT-ING PROTECTED
COMPONENT
51 HAZARD15 A Turn signals, Hazard warning
flashers
52 SUN
ROOF20 A Moonroofí
53 WASHER20 A Front washer, Rear window
wiper and washer
54―― ―
55 P/WIND R30 A
―
56 P/WIND L30 A―
57 ALARM7.5 A ―
58M/DEF 7.5 A Mirror Defroster
59―― ―
60HEAD
LOW R15 A Headlight low beams (RH),
Headlight levelingí
61HEAD
LOW L15 A Headlight low beams (LH)
62―― ―
63―― ―
8-52
Maintenance and Care
íSome models.
Owner Maintenance
Mazda3_8T96-EA-04J_Edition3 Page294
Wednesday, May 11 2005 3:39 PM
Form No.8T96-EA-04J

Black plate (295,1)
DESCRIP-TIONFUSERAT-ING PROTECTED
COMPONENT
64―― ―
65SAS 10 A Supplemental restraint system
66METER 10 A Instrument cluster,
Immobilizer system, Shift
lock system
67 IGNITION20 A ABSí, EHPAS
68WIPER 20 A Windshield wiper
69 ENGINE20 A
For protection of various
circuits
70IG SIG 10 A Auto wiperí
71SAS 2 7.5 A Supplemental restraint system
72―― ―
73―― ―
74SEAT
WARM20 A ―
75 D/LOCK 125 A Power door lock
76A/C 10 AAir conditioner, Heater
control unit
77 P/WIND L30 A Power window (LH)í
78 P/WIND R30 A Power window (RH)í
79BACK 10 A Reverse lights
80SUN
ROOF7.5 A Moonroofí
81TAIL L 7.5 A Taillights (LH), Parking lights
(LH)
82 ILLUMI7.5 A Illumination
83―― ―
84―― ―
85―― ―
86―― ―
Maintenance and Care
Owner Maintenance
8-53íSome models.
Mazda3_8T96-EA-04J_Edition3 Page295
Wednesday, May 11 2005 3:39 PM
Form No.8T96-EA-04J