MAZDA MODEL 3 HATCHBACK 2011 Owners Manual (in English)

Black plate (420,1)
Bulb type
(4 Door)
1. Pull the center of each plastic retainerand remove the retainers and the trunk
end trim.
InstallationRemoval
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order of removal.
(5 Door)
1. Make sure the ignition is switched off, and the headlight switch is off. 2. Remove the cover.
Left side
Right side
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order of removal.
8-48
Maintenance and Care
Owner Maintenance
Mazda3_8BM6-EC-10F_Edition1 Page420
Monday, June 7 2010 2:35 PM
Form No.8BM6-EC-10F

Black plate (421,1)
Rear turn signal lights
(4 Door)
1. Make sure the ignition is switched off,and the turn signal switch is off.
2. Pull the center of each plastic retainer and remove the retainers and the trunk
end trim.
InstallationRemoval
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order of removal.
(5 Door)
1. Make sure the ignition is switched off, and the turn signal switch is off. 2. Remove the cover.
Left side
Right side
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order of removal.
Maintenance and Care
Owner Maintenance
8-49
Mazda3_8BM6-EC-10F_Edition1 Page421
Monday, June 7 2010 2:35 PM
Form No.8BM6-EC-10F

Black plate (422,1)
Reverse lights
(4 Door)
1. Make sure the ignition is switched off,and the headlight switch is off.
2. Pull the center of each plastic retainer and remove the retainers and the trunk
end trim.
InstallationRemoval
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order of removal.
(5 Door)
1. Make sure the ignition is switched off, and the headlight switch is off. 2. Remove the cover.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order of removal.
High-mount brake light
(4 Door)
1. Make sure the ignition is switched off,and the headlight switch is off.
8-50
Maintenance and Care
Owner Maintenance
Mazda3_8BM6-EC-10F_Edition1 Page422
Monday, June 7 2010 2:35 PM
Form No.8BM6-EC-10F

Black plate (423,1)
2. Pull the center of each plastic retainerand remove the retainers and the trunk
end trim.
InstallationRemoval
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order of removal.
(5 Door)
LED type
Due to the complexity and difficulty of
the procedure, the LED bulbs should be
replaced by an Authorized Mazda Dealer.
NOTE
LED bulb replacement is not possible. The
rear combination component must be replaced.
Bulb type
1. Make sure the ignition is switched off, and the headlight switch is off.
2. Remove the liftgate upper trim.
3. Disconnect the electrical connector from the bulb by pressing the tab on
the connector with your finger and
pulling the connector sideward to the
left.
4. Turn the socket and bulb assemblycounterclockwise and remove it.
Maintenance and Care
Owner Maintenance
8-51
Mazda3_8BM6-EC-10F_Edition1 Page423
Monday, June 7 2010 2:35 PM
Form No.8BM6-EC-10F

Black plate (424,1)
5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse orderof removal.
License plate lights
1. Make sure the ignition is switched off,and the headlight switch is off.
2. Wrap a flathead screwdriver with a soft cloth to prevent damage to the lens,
and then remove the lens by carefully
prying on the edge of the lens with a
flathead screwdriver.
3. Disconnect the bulb by pulling it out.
4. Install the new bulb in the reverse orderof removal.
qReplacing Interior Light Bulbs
Overhead light/Map lights (Front),
Overhead light (Rear), Vanity mirror
lightsí
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens, and then remove the lens by
carefully prying on the edge of the lens
with the flathead screwdriver.
2. Disconnect the bulb by pulling it out.
Overhead light/Map lights (Front)
8-52
Maintenance and Care
íSome models.
Owner Maintenance
Mazda3_8BM6-EC-10F_Edition1 Page424
Monday, June 7 2010 2:35 PM
Form No.8BM6-EC-10F

Black plate (425,1)
Overhead light (Rear)
Edge
Vanity mirror lightsí
3. Install the new bulb in the reverse orderof removal.
Trunk light (4 Door)
1. Press both sides of the lens cap toremove it. 2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of removal.
Luggage compartment light (5 Door)
1. Wrap a small flathead screwdriver witha soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
flathead screwdriver.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order of removal.
Maintenance and Care
Owner Maintenance
8-53íSome models.
Mazda3_8BM6-EC-10F_Edition1 Page425
Monday, June 7 2010 2:35 PM
Form No.8BM6-EC-10F

Black plate (426,1)
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing the fuses on the vehicle's left
side
If the electrical system does not work,
first inspect the fuses on the vehicle's left
side.
1. Turn off the ignition switch and other
switches.
2. Remove the cover.
3. Pull the fuse straight out with the fuse puller provided on the inside of the
engine compartment fuse block cover.
4. Inspect the fuse and replace it if it'sblown.
Normal Blown
5. Insert a new fuse of the same amperage
rating, and make sure it fits tightly. If it
does not fit tightly, have an expert
install it. We recommend an
Authorized Mazda Dealer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or CIGAR circuit.
CAUTION
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
8-54
Maintenance and Care
Owner Maintenance
Mazda3_8BM6-EC-10F_Edition1 Page426
Monday, June 7 2010 2:35 PM
Form No.8BM6-EC-10F

Black plate (427,1)
Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses in
the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:
1. Turn off the ignition switch and allother switches.
2. Remove the fuse block cover.
3. If any fuse but the MAIN fuse is blown, replace it with a new one of the
same amperage rating .
Normal
Blown
WARNING
Do not replace the main fuse by
yourself. Have an Authorized Mazda
Dealer perform the replacement:
Replacing the fuse by yourself is
dangerous because the MAIN fuse is
a high current fuse. Incorrect
replacement could cause an electrical
shock or a short circuit resulting in a
fire.
Maintenance and Care
Owner Maintenance
8-55
Mazda3_8BM6-EC-10F_Edition1 Page427
Monday, June 7 2010 2:35 PM
Form No.8BM6-EC-10F

Black plate (428,1)
qFuse Panel Description
Fuse block (Engine compartment)
32 33 34 35
36 37 38 39
54
1 2 3 678
1312 14 15 16
22
11109
212019
23 24 25
29 30 3127
28
26
17 18
DESCRIPTION
FUSE
RATING PROTECTED COMPONENT
1 FAN 2 40 A Cooling fan
í
2 ENG MAIN 40 A Engine control system
3 BTN 1 50 A For protection of various circuits
4 A/C MAG 7.5 A Air conditioner
5 H/L HI 20 A Headlight high beam
6 FOG 15 A Fog lights
í
7 H/L WASH ――
8 SUNROOF 15 A Moonroofí
9 F.DEF RH ――
10 F.DEF LH ――
11 FAN 1 40 A Cooling fan
12 ROOM 15 A Interior lights
13 TCM 15 A TCM
í
14 DSC 20 A Dynamic Stability Control systemí
15BTN 2 7.5 A For protection of various circuits
16 AT PUMP ――
17 HEATER 40 A Air conditioner
8-56
Maintenance and Care
íSome models.
Owner Maintenance
Mazda3_8BM6-EC-10F_Edition1 Page428
Monday, June 7 2010 2:35 PM
Form No.8BM6-EC-10F

Black plate (429,1)
DESCRIPTIONFUSE
RATING PROTECTED COMPONENT
18 INJ 30 A Injector
í
19R.DEF 30 A Rear window defroster
20 IGKEY 2 40 A For protection of various circuits
21 IGKEY 1 40 A For protection of various circuits
22 HORN 15 A Horn
23 STOP 15 A Brake lights
24
10A Engine control system
25 FUEL PUMP 25 A Fuel system
26 ABS 40 A ABS
27 SEAT WARM 20 A Seat warmer
í
28 EHPAS 80 A Electro-Hydraulic Power Assist Steering
29 ―― ―
30 ABS IG 7.5 A ABS
31 SWS 7.5 A Air bag
32 H/L LO RH 15 A Headlight low beam (RH)
33 H/L LO LH 15 A Headlight low beam (LH)
34 ILLUM 7.5 A Dashboard illumination
35 TAIL 15 A Taillights
36 ENG INJ 15 A Engine control system
37 ENG BAR 15 A PCM
38 ENG BAR 2 20 A PCM
39 ETV 15 A Electric throttle valve
Maintenance and Care
Owner Maintenance
8-57íSome models.
Mazda3_8BM6-EC-10F_Edition1 Page429
Monday, June 7 2010 2:35 PM
Form No.8BM6-EC-10F