warning MAZDA MODEL 3 HATCHBACK 2015 Owners Manual (in English)
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2015, Model line: MODEL 3 HATCHBACK, Model: MAZDA MODEL 3 HATCHBACK 2015Pages: 689, PDF Size: 7.08 MB
Page 267 of 689
4–117
When Driving
i-ACTIVSENSE
NOTE
The RVM warning indicator light may illuminate for stationary objects in or on the
edge of the road, such as guardrails, tunnels, and side walls.
Objects such as guardrails and concrete walls
running alongside the vehicle.Places where the width between guardrails or
walls on each side of the vehicle narrows.
The walls at the entrance and exits of tunnels,
turnouts.
If a trailer is being towed or a vehicle carrier is equipped to the rear of the vehicle, the
rear vehicle monitoring system may not operate correctly because radar emission could
be obstructed. Turn off the rear vehicle monitoring system.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 268 of 689
4–118
When Driving
i-ACTIVSENSE
RVM Warning Indicator Light
The rear vehicle monitoring system alerts the driver to the presence of another vehicle in
an adjacent lane using the RVM warning indicator lights and the warning chime while the
system is operational.
RVM warning indicator light
The RVM warning indicator lights are installed to the left and right outside mirrors. The
warning indicator light illuminates when a vehicle approaching from the rear in an adjacent
lane is detected. A warning indicator light fl ashes when the direction indicator lever is
operated to the side where the RVM warning indicator light is illuminated to alert the driver.
Illumination dimmer cancel function
Normally, when the headlight switch is turned to the
or position, the brightness of
the RVM warning indicator lights is dimmed when they illuminate.
When driving on snow and fog bound roads where the brightness of the surrounding light
makes it diffi cult to see a RVM warning indicator light while it is dimmed, rotating the
instrument panel illumination knob clockwise fully cancels the dimmer function and restores
the brightness of the RVM warning indicator lights to full brightness.
Refer to Instrument panel Illumination on page 4-28 .
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 270 of 689
*Some models.4–120
When Driving
i-ACTIVSENSE
Distance Recognition Support System (DRSS) *
The Distance Recognition Support System (DRSS) measures the distance between your
vehicle and a vehicle ahead using a radar sensor while the vehicle speed is 30 km/h or faster
(19 mph or faster), and indicates a recommended distance to maintain between the vehicles.
Furthermore, if your vehicle approaches a vehicle ahead more closely than the appropriate
distance to maintain between the vehicles, the vehicle-ahead indication in the display is
fl ashed to advise the driver to keep a safer distance from the vehicle ahead.
WARNING
Do not rely completely on the Distance Recognition Support System (DRSS) and always
drive carefully:
The Distance Recognition Support System (DRSS) provides advice for safer driving and
notifi es the driver of a recommended, safer distance to maintain with a vehicle ahead.
The ability to detect a vehicle ahead is limited depending on the type of vehicle ahead,
the weather conditions, and the traffi c conditions. Therefore, if the accelerator and
brake pedals are not operated correctly it could lead to an accident. Always verify the
safety of the surrounding area and depress the brake pedal or accelerator pedal while
keeping a safer distance from vehicles ahead or on-coming vehicles.
NOTE
The Distance Recognition Support System (DRSS) operates when all of the following
conditions are met:
The ignition is switched ON.
The Distance Recognition Support System (DRSS) is on.
The selector lever is in a position other than reverse (R).
The vehicle speed is 30 km/h or faster (19 mph or faster).
The objects which activate the system are 4-wheeled vehicles.
The Distance Recognition Support System (DRSS) may also operate in the presence of
motorcycles and bicycles.
The Distance Recognition Support System (DRSS) system may not operate normally
under the following conditions:
The Dynamic Stability Control (DSC) has a malfunction.
The vehicle ahead is travelling at an extremely slow speed.
The system does not operate with the following objects:
Vehicles approaching in the opposite direction.
Stationary objects (stopped vehicles, obstructions)
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 271 of 689
4–121
When Driving
i-ACTIVSENSE
Indication on Display
The Distance Recognition Support System (DRSS) operation status is indicated in the active
driving display. Regarding malfunctions, check the vehicle conditions or have it inspected
by an expert repairer, we recommend an Authorised Mazda Repairer according to the
content of the displayed message.
Refer to Warning/Indicator Lights on page 4-40 .
NOTE
When the ignition is switched off, the operation status before the system was turned
off is maintained. For example, if the ignition is switched off with the Distance
Recognition Support System (DRSS) operable, the system will be operable when the
ignition is switched ON the next time.
The Distance Recognition Support System (DRSS) can be turned on/off and the
system's sensitivity can be changed.
Refer to Personalisation Features on page 9-16 .
Vehicle ahead
display
Distance between
vehicle display
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 273 of 689
*Some models.4–123
When Driving
i-ACTIVSENSE
Mazda Radar Cruise Control (MRCC) *
The Mazda Radar Cruise Control (MRCC) system is designed to maintain headway control *1
according to the vehicle speed using a radar sensor (front) to detect the distance to a vehicle
ahead, which frees the driver from having to constantly use the accelerator or brake pedals.
*1 Headway Control: Control of the distance between your vehicle and the vehicle ahead
detected by the Mazda Radar Cruise Control (MRCC) system.
Additionally, if your vehicle starts closing in on the vehicle ahead because, for example, the
vehicle ahead brakes suddenly, a warning sound and a warning indication in the display are
activated simultaneously to alert you to maintain a suffi cient distance between the vehicles.
The possible vehicle speed setting ranges are as follows:
(European models)
About 30 km/h (19 mph) to 200 km/h (124 mph)
(Except European models)
About 30 km/h (19 mph) to 145 km/h (90 mph)
Use the Mazda Radar Cruise Control (MRCC) system on expressways and other highways
which do not require a lot of repeated acceleration and deceleration.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 274 of 689
4–124
When Driving
i-ACTIVSENSE
WARNING
Do not rely completely on the Mazda Radar Cruise Control (MRCC) system and always
drive carefully:
The Mazda Radar Cruise Control (MRCC) system is designed to reduce load on the
driver, and although it maintains a constant vehicle speed, or specifi cally, it maintains
a constant distance between your vehicle and the detected vehicle ahead according to
the vehicle speed, the system has detection limitations depending on the type of vehicle
ahead and its conditions, the weather conditions, and the road conditions. Additionally,
the system may be unable to decelerate suffi ciently to avoid hitting the vehicle ahead if
the vehicle ahead applies the brakes suddenly or another vehicle cuts into the driving
lane, which could result in an accident. Always verify the safety of the surrounding area
and depress the brake pedal or accelerator pedal while keeping a safer distance from
vehicles ahead or on-coming vehicles.
Do not use the Mazda Radar Cruise Control (MRCC) system in the following locations.
Otherwise, it could lead to an accident:
Roads with sharp curves and where vehicle traffi c is heavy and there is insuffi cient
space between vehicles. Roads where frequent and repetitive acceleration and
deceleration occur (Driving under these conditions using the Mazda Radar Cruise
Control (MRCC) system is not possible).
When entering and exiting interchanges, service areas, and parking areas of
highways (If you exit a highway while headway control is in use, the vehicle ahead
will no longer be tracked and your vehicle may accelerate to the set speed).
Slippery roads such as ice or snow-bound roads (The tyres could spin causing you to
lose vehicle control).
Long descending slopes (to maintain distance between vehicles, the system
automatically and continuously applies the brakes which could result in the loss of
brake power).
For the purposes of safety, switch the Mazda Radar Cruise Control (MRCC) system off
when it is not being used.
CAUTION
If the vehicle is towed or you are towing something, switch the Mazda Radar Cruise
Control (MRCC) system off to prevent an incorrect operation.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 275 of 689
4–125
When Driving
i-ACTIVSENSE
NOTE
The Mazda Radar Cruise Control (MRCC) system operates when all of the following
conditions are met.
The vehicle speed is as follows:
(European models)
About 30 km/h (19 mph) to 200 km/h (124 mph)
(Except European models)
About 30 km/h (19 mph) to 145 km/h (90 mph)
The Mazda Radar Cruise Control (MRCC) system is turned on.
The parking brake is not applied.
The Smart Brake Support (SBS) warning light (amber) does not illuminate.
The Dynamic Stability Control (DSC) is operating normally.
(Manual transaxle)
The shift lever is in a position other than reverse (R) or neutral (N).
The clutch pedal is not depressed.
(Automatic transaxle)
The selector lever is in the drive (D) position or manual (M) position (manual
mode).
In the following cases, the warnings may not activate even if your vehicle starts
closing in on the vehicle ahead.
You are driving at the same speed as the vehicle ahead.
Directly after the Mazda Radar Cruise Control (MRCC) system has been set.
When the accelerator pedal is depressed or directly after the accelerator pedal is
released.
Another vehicle cuts into the driving lane.
The following are not detected as physical objects.
Vehicles approaching in the opposite direction
Pedestrians
Stationary objects (stopped vehicles, obstructions)
If a vehicle ahead is travelling at an extremely low speed, the system may not detect it
correctly.
During headway control travel, do not set the system on two-wheeled vehicles such as
motorcycles and bicycles.
Do not use the Mazda Radar Cruise Control (MRCC) system under conditions in
which the close proximity warnings are frequently activated.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 276 of 689
4–126
When Driving
i-ACTIVSENSE
NOTE
During headway control travel, the system accelerates and decelerates your vehicle
in conjunction with the speed of the vehicle ahead. However, if it is necessary to
accelerate for a lane change or if the vehicle ahead brakes suddenly causing you to
close in on the vehicle rapidly, accelerate using the accelerator pedal or decelerate
using the brake pedal depending on the conditions.
While the Mazda Radar Cruise Control (MRCC) system is in use, it does not cancel
even if the selector lever (automatic transaxle)/shift lever (manual transaxle) is
operated and any intended engine braking will not occur. If deceleration is required,
lower the vehicle speed setting or depress the brake pedal.
The brake lights are illuminated while the Mazda Radar Cruise Control (MRCC)
automatic braking is operating, however, they may not be illuminated while the
vehicle is on a down slope at the set vehicle speed or travelling at a constant speed and
following a vehicle ahead.
The Mazda Radar Cruise Control (MRCC) warning light (amber) fl ashes when the
system has a malfunction.
Refer to Warning Lights on page 4-41 .
Mazda Radar Cruise Control (MRCC) Display Indication
The setting status and operation conditions of the Mazda Radar Cruise Control (MRCC)
system are indicated in the active driving display.
Vehicle ahead display
MRCC Distance between vehicle display
MRCC Set vehicle
speed
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 277 of 689
4–127
When Driving
i-ACTIVSENSE
Close Proximity Warning
If your vehicle rapidly closes in on the vehicle ahead because the vehicle applies the brakes
suddenly while you are travelling in headway control, the warning sound activates and
the brake warning is indicated in the display. Always verify the safety of the surrounding
area and depress the brake pedal while keeping a safer distance from the vehicle ahead.
Additionally, always keep a safer distance from the vehicles behind you.
Setting the System
To Activate
With adjustable speed limiter
To activate the system, press the ON/OFF switch.
Without adjustable speed limiter
To activate the system, press the ON switch.
ON/OFF switch
OFF switch ON switch Without Adjustable Speed Limiter With Adjustable Speed Limiter
CANCEL switch CANCEL switch
Switch SwitchRESUME
switchRESUME
switch
Switch Switch
SET+/SET- switch SET+/SET- switch
When the system is activated, the vehicle speed and the distance between vehicles while in
headway control can be set. The Mazda Radar Cruise Control (MRCC) indication is shown
in the active driving display.
NOTE
When the ignition is switched to ACC or OFF while the Mazda Radar Cruise Control
(MRCC) is ON, the Mazda Radar Cruise Control (MRCC) remains ON automatically.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 280 of 689
4–130
When Driving
i-ACTIVSENSE
To accelerate using the accelerator
pedal
Depress the accelerator pedal and press
and release the SET
or SET switch at
the desired speed. If a switch cannot be
operated, the system returns to the set
speed when you release your foot from the
accelerator pedal.
CAUTION
The warnings and brake control do not
operate while the accelerator pedal is
depressed.
NOTE
When accelerating using the SET
switch while in headway control, the
set vehicle speed can be adjusted but
acceleration is not possible. If there
is no longer a vehicle ahead,
acceleration continues until reaching
the set vehicle speed. Check the set
vehicle speed by viewing the set
vehicle speed display in the active
driving display.
When depressing the accelerator
pedal, the inter-vehicle distance
display in the display in the
instrument cluster changes to the
white-line display.
The minimum settable speed is 30
km/h (19 mph). If the set vehicle
speed reaches 30 km/h (19 mph)
using the switch operation, constant
speed travel is maintained at about
30 km/h (19 mph) even if the SET
switch is pressed. The Mazda Radar
Cruise Control (MRCC) system is
not cancelled.
To Deactivate
With adjustable speed limiter
The Mazda Radar Cruise Control (MRCC)
is cancelled when the ON/OFF switch is
pressed.
Without adjustable speed limiter
The Mazda Radar Cruise Control (MRCC)
is cancelled when the OFF switch is
pressed.
When the system is temporarily
cancelled
In the following cases, the Mazda Radar
Cruise Control (MRCC) system is
temporarily cancelled and the “MRCC
Cancelled” indication is displayed in
the display in the instrument cluster.
The Mazda Radar Cruise Control
(MRCC) indicator light (green) turns off
simultaneously.
The CANCEL switch is pressed.
The brake pedal is depressed.
The parking brake is applied.
The selector lever is shifted to park (P),
neutral (N) or reverse (R) (automatic
transaxle).
The shift lever is in the reverse (R)
position (manual transaxle).
. B [ E B @ & ' & & " @ & E J U J P O J O E C