cooling MAZDA MODEL 3 HATCHBACK 2015 Owners Manual (in English)

3–30
Before Driving
Fuel and Emission
Engine Exhaust (Carbon monoxide)
WARNING
Do not drive your vehicle if you smell exhaust gas inside the vehicle:
Engine exhaust gas is dangerous. This gas contains carbon monoxide (CO), which is
colourless, odourless, and poisonous. When inhaled, it can cause loss of consciousness
and death. If you smell exhaust gas inside the vehicle, keep all windows fully open and
contact an expert repairer, we recommend an Authorised Mazda Repairer immediately.
Do not run the engine when inside an enclosed area:
Running the engine inside an enclosed area, such as a garage, is dangerous. Exhaust
gas, which contains poisonous carbon monoxide, could easily enter the cabin. Loss of
consciousness or even death could occur.
Open the windows or adjust the heating or cooling system to draw fresh air when idling
the engine:
Exhaust gas is dangerous. When the vehicle is stopped with the windows closed and
the engine running for a long time even in an open area, exhaust gas, which contains
poisonous carbon monoxide, could enter the cabin. Loss of consciousness or even death
could occur.
Clear snow from underneath and around your vehicle, particularly the tail pipe, before
starting the engine:
Running the engine when a vehicle is stopped in deep snow is dangerous. The exhaust
pipe could be blocked by the snow, allowing exhaust gas to enter the cabin. Because
exhaust gas contains poisonous carbon monoxide, it could cause loss of consciousness
or even death to occupants in the cabin.
.B[EB@&'&&"@&EJUJPOJOEC







4–12
When Driving
Start/Stop Engine
Turning the Engine Off
WARNING
Do not stop the engine while the
vehicle is moving:
Stopping the engine while the vehicle is
moving for any reason other than in an
emergency is dangerous. Stopping the
engine while the vehicle is moving will
result in reduced braking ability due to
the loss of power braking, which could
cause an accident and serious injury.
1. Stop the vehicle completely.
2. (Manual transaxle)
Shift into neutral and set the parking
brake.
(Automatic transaxle)
Shift the selector lever to the P position
and set the parking brake.
3. Press the push button start to turn off
the engine. The ignition position is off.
CAUTION
When leaving the vehicle, make sure the
push button start is off.
NOTE
 (SKYACTIV-G 1.5, SKYACTIV-G
2.0)
 The cooling fan in the engine
compartment could turn on for a few
minutes after the ignition is switched
from ON to OFF, whether or not the
A/C is on or off, to cool the engine
compartment quickly.
  When the push button start is pressed
from ON to ACC or OFF, the KEY
indicator light (green) may fl ash for
approximately 30 seconds indicating
that the remaining battery power of
the key is low.
 Replace with a new battery before
the key becomes unusable.
 Refer to Key Battery Replacement on
page 6-43 .
 (Automatic transaxle) If the engine is turned off while the
selector lever is in a position other
than P, the ignition switches to ACC.
Emergency Engine Stop
Continuously pressing the push button
start or quickly pressing it any number of
times while the engine is running or the
vehicle is being driven will turn the engine
off immediately. The ignition switches to
ACC.
.B[EB@&'&&"@&EJUJPOJOEC







4–15
When Driving
Start/Stop Engine
NOTE
To ensure safe and comfortable use of the vehicle, the i-stop function controls engine stop
and restart automatically while constantly monitoring operations other than those of the
driver, such as the vehicle's interior and exterior environment, and the operational status
of the vehicle.
 
 The engine stops automatically when all of the following conditions are met:




 The engine has been started and the vehicle is driven for a certain period. The i-stop
function will not operate if the vehicle is not fi rst driven, no matter how long the
engine is left idling. Also, after the vehicle is driven for a certain period and then
stopped, the i-stop function (automatic engine-stop and restart) operates only once
while the vehicle is stopped.
 


 The engine is started with the bonnet closed.



(SKYACTIV-G 1.5, SKYACTIV-G 2.0)
 The engine has warmed up suffi ciently.



(Manual transaxle)
 The vehicle speed is about 3 km/h (2 mph) or less.
(Automatic transaxle)
 The vehicle is stopped.



 The battery is in good condition.



 The bonnet is closed.



 All the doors and the liftgate/boot lid are closed.



 The driver's seat belt is fastened.



 The windscreen defroster switch is off.



(Dual-zone automatic air-conditioning)
 The temperature setting dial for the air conditioning is set to a position other than
maximum heating/maximum cooling (A/C ON).
 


(Dual-zone automatic air-conditioning)
 The vehicle's interior temperature and the set temperature for the air-conditioning
system are nearly the same.
 


(European model)
 The vehicle is driven at elevations of 1,800 meters (5,905 ft) or less.
(Except European model)
 The vehicle is driven at elevations of 1,500 meters (4,921 ft) or less.



 The i-stop warning light (amber) is not illuminated or fl ashing.



 The keyless entry system operate normally.



 The brakes are applied suffi ciently (brake system vacuum level is suffi cient).



 The steering wheel is not being operated.
.B[EB@&'&&"@&EJUJPOJOEC







4–18
When Driving
Start/Stop Engine
NOTE
  If any one of the following operations is performed after the engine has been
automatically stopped (shift lever is in neutral position for vehicles with manual
transaxle), the engine will restart automatically even though the clutch pedal is not
depressed (manual transaxle) or the brake pedal is not released (automatic transaxle).
However, for safety reasons, if the shift lever is in a position other than neutral for
vehicles with manual transaxle, the engine will not restart automatically.
 


 The i-stop OFF switch is pressed for several seconds.



(Dual-zone automatic air-conditioning)
 The temperature setting dial of the air conditioning is set to maximum heating/
maximum cooling (A/C ON).
 


 The windscreen defroster switch is on.



(Except European model)
 The driver intends to get out of the vehicle (driver's seat belt is unfastened and any
door or the liftgate/boot lid is opened).
 


 The brakes are released slightly on a slope and the vehicle begins to move.

(Automatic transaxle)




 The accelerator pedal is depressed while the selector lever is in the D/M position
(not second gear fi xed mode).




 The selector lever is shifted to the R position.



 The selector lever is shifted from the N or P position to the D/M position (not second
gear fi xed mode).




 The steering wheel is operated with the selector lever in the D/M position (not
second gear fi xed mode).




 The selector lever is in the M position, second gear fi xed mode. 

 If any one of the following vehicle conditions occur after the engine has been
automatically stopped (shift lever is in neutral position for vehicles with manual
transaxle), the engine will restart automatically even though the clutch pedal is not
depressed (manual transaxle) or the brake pedal is not released (automatic transaxle).
However, for safety reasons, if the shift lever is in a position other than neutral for
vehicles with manual transaxle, the engine will not restart automatically.
 


(Dual-zone automatic air-conditioning)
 There is a large difference between the cabin temperature and the temperature set for
the air-conditioning system.
 


 Two minutes have elapsed since the i-stop function started operating.



 The battery power is depleted.
.B[EB@&'&&"@&EJUJPOJOEC







5–2
Interior Features
Air-Conditioning System
Operating Tips
 












 Operate the air-conditioning system with
the engine running.
 


 To prevent the battery from being
discharged, do not leave the fan control
dial on for a long period of time with the
ignition switched ON when the engine is
not running.
 


(With i-stop)
 The airfl ow amount may decrease
slightly while the i-stop function is
operating.
 


 Clear all obstructions such as leaves,
snow and ice from the bonnet and the
air inlet in the cowl grille to improve the
system effi ciency.




 Use the air-conditioning system to defog
the windows and dehumidify the air.
 


 The recirculate mode should be used
when driving through tunnels or while in
a traffi c jam, or when you would like to
shut off outside air for quick cooling of
the interior.
 


 Use the outside air position for
ventilation or windscreen defrosting.
 


 If the vehicle has been parked in direct
sunlight during hot weather, open the
windows to let warm air escape, then
run the air-conditioning system.
(With A/C switch)
 




 Run the air conditioner about 10 minutes
at least once a month to keep internal
parts lubricated.
 


 Have the air conditioner checked before
the weather gets hot. Lack of refrigerant
may make the air conditioner less
effi cient.

 The refrigerant specifi cations are
indicated on a label attached to the
inside of the engine compartment. Check
the label before refi lling the refrigerant.
If the wrong type of refrigerant is used,
it could result in a serious malfunction
of the air conditioner.
  For details, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
Label
.B[EB@&'&&"@&EJUJPOJOEC







5–7
Interior Features
Air-Conditioning System
Air intake selector
This switch controls the source of air
entering the vehicle.
Press the air intake selector switch to
alternate between the outside air and
recirculated air positions.
Recirculated air position (
)
Outside air is shut off. Air within the
vehicle is recirculated.
Outside air position (
)
Outside air is allowed to enter the
cabin. Use this mode for ventilation or
windscreen defrosting.
WARNING
Do not use the recirculated air position
in cold or rainy weather:
Using the recirculated air position in
cold or rainy weather is dangerous as it
will cause the windows to fog up. Your
vision will be hampered, which could
lead to a serious accident.
Heating
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the outside
air position.
3. Set the temperature control dial to the
hot position.
4. Set the fan control dial to the desired
speed.
5. If dehumidifi ed heating is desired, turn
on the air conditioner.
NOTE
  If the windscreen fogs up easily, set
the mode selector dial to the
position.  If cooler air is desired at face level,
set the mode selector dial at the
position and adjust the temperature
control dial to maintain maximum
comfort.
  The air to the fl oor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
  In the position, the outside air
position is automatically selected.
The air intake selector cannot be
changed to the recirculated air
position.
Cooling (With air conditioner)
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
cold position.
3. Set the fan control dial to the desired
speed.
4. Turn on the air conditioner by pressing
the A/C switch.
5. After cooling begins, adjust the fan
control dial and temperature control
dial as needed to maintain maximum
comfort.
.B[EB@&'&&"@&EJUJPOJOEC







5–8
Interior Features
Air-Conditioning System
CAUTION
If the air conditioner is used while
driving up long hills or in heavy traffi c,
monitor the engine coolant temperature
warning light to see if it is illuminated or
fl ashing (page 4-40 ).
The air conditioner may cause engine
overheating. If the warning light is
illuminated or fl ashing, turn the air
conditioning off (page 7-26 ).
NOTE

(Type A) When maximum cooling is desired,
set the temperature control dial to
the extreme cold position and set the
air intake selector to the recirculated
air position, then turn the fan control
dial fully clockwise.
 (Type B) When maximum cooling is desired,
set the temperature control dial to the
extreme cold position and set the air
intake selector to the recirculated air
position, then set the fan control dial
to position 4.
  If warmer air is desired at fl oor level,
set the mode selector dial at the
position and adjust the temperature
control dial to maintain maximum
comfort.
  The air to the fl oor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
Ventilation
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the outside
air position.
3. Set the temperature control dial to the
desired position.
4. Set the fan control dial to the desired
speed.
Windscreen Defrosting and
Defogging
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
desired position.
3. Set the fan control dial to the desired
speed.
4. If dehumidifi ed heating is desired, turn
on the air conditioner.
WARNING
Do not defog the windscreen using the
position with the temperature
control set to the cold position:
Using the
position with the
temperature control set to the cold
position is dangerous as it will cause
the outside of the windscreen to fog up.
Your vision will be hampered, which
could lead to a serious accident. Set the
temperature control to the hot or warm
position when using the
position.
.B[EB@&'&&"@&EJUJPOJOEC







5–11
Interior Features
Air-Conditioning System
NOTE
  With the airfl ow mode set to the
position and the temperature control
dial set at a medium temperature,
heated air is directed to the feet and
air at a comparably lower
temperature will fl ow through the
central, left and right vents.
  When the fan control dial is ON, and
the mode selector dial is in the
position, the air conditioner is
automatically turned on and the
outside air position is automatically
selected to defrost the windscreen. In
the
position, the outside air
position cannot be changed to the
recirculated air position.
A/C switch
The air conditioning (cooling/
dehumidifying functions) can be turned on
or off by pressing the switch while the fan
control dial is at a position other than 0.
The indicator light turns on while the air
conditioning is operating.
NOTE
The air conditioner may not function
when the outside temperature
approaches 0 °C (32 °F).
Air intake selector
Outside or recirculated air positions can be
selected. Press the switch to select outside/
recirculated air positions.
Recirculated air position (indicator light
illuminated)
Outside air is shut off. Use this position
when going through tunnels, driving in
congested traffi c (high engine exhaust
areas) or when quick cooling is desired.
Outside air position (indicator light
turned off)
Outside air is allowed to enter the
cabin. Use this mode for ventilation or
windscreen defrosting.
WARNING
Do not use the position in cold or
rainy weather:
Using the
position in cold or rainy
weather is dangerous as it will cause
the windows to fog up. Your vision will
be hampered, which could lead to a
serious accident.
.B[EB@&'&&"@&EJUJPOJOEC







5–15
Interior Features
Air-Conditioning System
OFF switch
Pressing the OFF switch shuts off the air-
conditioning system.
Temperature control dial
This dial controls temperature. Turn it
clockwise for hot and anticlockwise for
cold.
 


 When the DUAL switch is off:
 Turn the driver temperature control dial
to control the temperature throughout
the entire cabin.
 


 When the DUAL switch is on:
 Turn the driver or front passenger
temperature control dial to
independently control the temperature
on each side of the cabin.
NOTE
The air-conditioning system changes to
the individual operation mode ( DUAL
switch indicator light illuminated) by
turning the front passenger temperature
control dial even when the DUAL
switch is off, which allows individual
control of the set temperature for the
driver and front passenger.
Fan control switch
The fan has seven speeds. The selected
speed will be displayed.
Mode selector switch
The desired airfl ow mode can be selected
(page 5-4 ).
NOTE
  With the airfl ow mode set to the
position and the temperature control
dial set at a medium temperature,
heated air is directed to the feet and
air at a comparably lower
temperature will fl ow through the
central, left and right vents.
  To set the air vent to , press the
windscreen defroster switch.
  In the position, the outside air
position is automatically selected.
A/C switch
Pressing the A/C switch while the AUTO
switch is turned on will turn off the air
conditioning (cooling/dehumidifying
functions).
The air conditioning can be turned on and
off by pressing the A/C switch while the
fan control switch is on.
Changes as follows each time the A/C
switch is pressed.
A/C
: A/C ECO
:Stop
NOTE

 The air conditioning operates when
the A/C switch is pressed even if the
fan is off.
  The A/C ECO function is designed
to economize use of the air-
conditioning system. “ A/C ECO ” is
displayed to indicate that the air-
conditioning system is operating at
optimum control.
  The air conditioner may not function
when the outside temperature
approaches 0 °C (32 °F).
.B[EB@&'&&"@&EJUJPOJOEC







5–16
Interior Features
Air-Conditioning System
Air intake selector
Outside or recirculated air positions can be
selected. Press the switch to select outside/
recirculated air positions.
Recirculated air position (
)
Outside air is shut off. Use this position
when going through tunnels, driving in
congested traffi c (high engine exhaust
areas) or when quick cooling is desired.
Outside air position (
)
Outside air is allowed to enter the
cabin. Use this mode for ventilation or
windscreen defrosting.
WARNING
Do not use the position in cold or
rainy weather:
Using the
position in cold or rainy
weather is dangerous as it will cause
the windows to fog up. Your vision will
be hampered, which could lead to a
serious accident.
DUAL switch
Use the DUAL switch to change the
mode between the individual operation
(driver and passenger) and interconnection
(simultaneous) modes.
Individual operation mode (indicator
light illuminated)
The set temperature can be controlled
individually for the driver and front
passenger.
Interconnection mode (indicator light
turned off)
The set temperature for the driver
and front passenger is controlled
simultaneously.
Windscreen defroster switch
Press the switch to defrost the windscreen
and front door windows.
.B[EB@&'&&"@&EJUJPOJOEC