ECU MAZDA MODEL 6 2009 (in English) User Guide

Black plate (50,1)
qLATCH Child-Restraint System
Installation Procedure (Rear
Outboard Seats)
1. Make sure the seatback is securely
latched by pushing it back until it is
fully locked.
2. Expand the area between the seat bottom and the seatback slightly to
verify the locations of the LATCH
lower anchors.
3. Raise the head restraint to the toplocked position.
Refer to Head restraints on page 2-12.
4. Secure the child-restraint system using BOTH LATCH lower anchors,
following the child-restraint system
manufacturer's instruction. Pull on the
child-restraint to be sure both anchors
are engaged.
5. If your child-restraint system came equipped with a tether, that means it is
very important to properly secure the
tether for child safety. Please carefully
follow the child-restraint system
manufacturer's instructions when
installing tethers. Anchor bracket location
Tether strap position
Anchor
bracket
Tether
strap
2-38
Essential Safety Equipment
Child Restraint
Mazda6_8Z64-EA-08H_Edition1 Page50
Wednesday, June 25 2008 10:3 AM
Form No.8Z64-EA-08H

Black plate (51,1)
WARNING
Use the tether and tether anchor only
for a child-restraint system:Using the tether or tether anchor to
secure anything but a child-restraint
system is dangerous. This could
weaken or damage the tether or
tether anchor and result in injury.
Always route the tether strap between
the head restraint and the seatback: Routing the tether strap on top of the
head restraint is dangerous. In a
collision the tether strap could slide
off the head restraint and loosen the
child-restraint system. The child-
restraint system could move which
may result in death or injury to the
child.
Always attach the tether strap to the
correct tether anchor position: Attaching the tether strap to the
incorrect tether anchor position is
dangerous. In a collision, the tether
strap could come off and loosen the
child-restraint system. If the child-
restraint system moves it could result
in death or injury to the child.
qLATCH Child-Restraint System
Installation Procedure (Rear
Center Seat)
The LATCH lower anchors at the center
of the rear seat are much further apart than
the sets of LATCH lower anchors for
child-restraint system installation at other
seating positions. Child-restraint systems
with rigid LATCH attachments cannot be
installed on the center seating position.
Some LATCH equipped child-restraint
systems can be placed in the center
position and will reach the nearest
LATCH lower anchors which are 466 mm
(18.35 in) apart. LATCH compatible
child-restraint systems (with attachments
on belt webbing) can be used at this
seating position only if the child-restraint
system manufacturer's instructions state
that the child-restraint system can be
installed to LATCH lower anchors that are
466 mm (18.35 in) apart. Do not attach
two child-restraint systems to the same
LATCH lower anchor. If your child-
restraint system has a tether, it must also
be used for your child's optimum safety.
Essential Safety Equipment
Child Restraint
2-39
Mazda6_8Z64-EA-08H_Edition1 Page51
Wednesday, June 25 2008 10:3 AM
Form No.8Z64-EA-08H

Black plate (52,1)
WARNING
Use the tether and tether anchor only
for a child-restraint system:Using the tether or tether anchor to
secure anything but a child-restraint
system is dangerous. This could
weaken or damage the tether or
tether anchor and result in injury.
Always attach the tether strap to the
correct tether anchor position: Attaching the tether strap to the
incorrect tether anchor position is
dangerous. In a collision, the tether
strap could come off and loosen the
child-restraint system. If the child-
restraint system moves it could result
in death or injury to the child.
1. Make sure the seatback is securely latched by pushing it back until it is
fully locked.
2. Expand the area between the seat bottom and the seatback slightly to
verify the locations of the LATCH
lower anchors.
3. Secure the child-restraint system usingBOTH LATCH lower anchors,
following the child-restraint system
manufacturer's instructions. Pull on the
child-restraint to be sure both anchors
are engaged.
4. If your child-restraint system came equipped with a tether, that means it is
very important to properly secure the
tether for child safety. Please carefully
follow the child-restraint system
manufacturer's instructions when
installing tethers.
Anchor bracket location
Tether strap position
Anchor
bracket Tether
strap
2-40
Essential Safety Equipment
Child Restraint
Mazda6_8Z64-EA-08H_Edition1 Page52
Wednesday, June 25 2008 10:3 AM
Form No.8Z64-EA-08H

Black plate (54,1)
WARNING
Seat belts must be worn in air bag equipped vehicles:Depending only on the air bags for protection during an accident is dangerous.
Alone, air bags may not prevent serious injuries. The appropriate air bags can be
expected to inflate only in the first collision with frontal, near frontal or side forces
that are at least moderate. Vehicle occupants should always wear seat belts.
Children should not ride in the front passenger seat: Placing a child, 12 years or under, in the front seat is dangerous. The child could be
hit by a deploying air bag and be seriously injured or even killed. Even if the front
passenger air bag deactivation indicator light illuminates, always move the front
passenger seat as far back as possible. A sleeping child is more likely to lean against
the door and be hit by the side air bag in a moderate, right-side collision. Whenever
possible, always secure a child 12 years and under on the rear seat with an
appropriate child-restraint system for the child's age and size.
Never use a rear-facing child-restraint system in the front seat with an air bag that
could deploy: Rear-facing child-restraint systems on the front seat are particularly dangerous even
though you may feel assured that a front passenger air bag will not deploy based on
the fact that the front passenger air bag deactivation indicator light illuminates.
The child-restraint system can be hit by a deploying air bag and moved violently
backward resulting in serious injury or death to the child.
Do not sit too close to the driver and front passenger air bags:Sitting too close to the driver and front passenger air bag modules or placing hands
or feet on them is extremely dangerous. The driver and front passenger air bags
inflate with great force and speed. Serious injuries could occur if someone is too
close. The driver should always hold onto only the rim of the steering wheel. The
front seat passenger should keep both feet on the floor. Front seat occupants should
adjust their seats as far back as possible and always sit upright against the
seatbacks with seat belts worn properly.
2-42
Essential Safety Equipment
SRS Air Bags
Mazda6_8Z64-EA-08H_Edition1 Page54
Wednesday, June 25 2008 10:3 AM
Form No.8Z64-EA-08H

Black plate (62,1)
Do not increase the total seated weight on the front passenger seat:When an infant or small child sits on the front passenger seat, increasing the total
seated weight on the front passenger seat from the total seated weight of
approximately 30 kg (66 lbs) is dangerous. The front passenger seat weight sensors
will detect the increased total seated weight, which could result in the unexpected
deployment of the front passenger front and side air bags and seat belt pretensioner
system in an accident and may cause serious injury. Increasing the total seated
weight on the front passenger seat beyond the total seated weight of approximately
30 kg (66 lbs) could result in the front passenger front and side air bags and seat
belt pretensioner system deployment in an accident under the following conditions,
for example:
ØLuggage or other items are placed on the seat with the child in the child-restraint
system.
Ø A rear passenger or luggage push or pull down on the front passenger seatback.
Ø A rear passenger steps on the front passenger seat rails with their feet.
Ø Luggage or other items are placed on the seatback or hung on the head restraint.
Ø Heavy items are placed in the seatback map pocket.
Ø The seat is washed.
Ø Liquids are spilled on the seat.
Ø The front passenger seat is moved backward, pushing into luggage or other items
placed behind it.
Ø The front passenger seatback contacts the rear seat.
Ø Luggage or other items are placed between the front passenger seat and driver
seat.
Ø Any accessories which might increase the total seated weight on the front
passenger seat are attached to the front passenger seat.
The front passenger front and side air bags and seat belt pretensioner systems will
deactivate if the total seated weight on the front passenger seat is less than
approximately 30 kg (66 lbs) and they will reactivate when the weight exceeds
approximately 42 kg (93 lbs).
CAUTION
Ø To assure proper deployment of the front air bag and to prevent damage to the
sensors in the front seat bottoms:
ØDo not place sharp objects on the front seat bottoms or leave heavy luggage on
them.
ØDo not spill any liquids on the front seats or under the front seats.
Ø To allow the sensors to function properly, always perform the following:
ØAdjust the front seats as far back as possible and always sit upright against the
seatbacks with seat belts worn properly.
ØIf you place your child on the front passenger seat, secure the child-restraint
system properly and slide the front passenger seat as far back as possible (page
2-34).
2-50
Essential Safety Equipment
SRS Air Bags
Mazda6_8Z64-EA-08H_Edition1 Page62
Wednesday, June 25 2008 10:3 AM
Form No.8Z64-EA-08H

Black plate (63,1)
NOTElThe system requires about 10 seconds to alternate between turning the front passenger front and
side air bags and seat belt pretensioner system on or off.
lThe front passenger air bag deactivation indicator light may illuminate repeatedly if luggage or
other items are put on the front passenger seat, or if the temperature of the vehicle's interior
changes suddenly.
lThe front passenger air bag deactivation indicator light may illuminate for 10 seconds if the total
seated weight on the front passenger seat changes.
lIf the front passenger air bag deactivation indicator light does not illuminate after installing a
child-restraint system on the front passenger seat, install the child-restraint system on the rear
seat and consult an Authorized Mazda Dealer as soon as possible.
Driver and front passenger buckle switches
The buckle switches on the front seat belts detect whether or not the front seat belts are
securely fastened and further control the deployment of the air bags.
qHow the Side and Curtain Air Bags Work
When air bag crash sensors detect a side impact of greater than moderate force, an
electrical current is sent to the inflators.
Gases are produced to inflate the side and curtain air bags and after the inflation, the side
and curtain air bags quickly deflate. However, the side air bag system for the front
passenger is designed to only deploy in accordance with the total seated weight on the front
passenger seat, however the curtains are not deactivated.
The side and curtain air bags will function only once. After that, the side and curtain air
bags will not work again and must be replaced. Only an Authorized Mazda Dealer can
replace the systems.
The side and curtain air bags will deploy only
on the side the vehicle receives the force of
the impact.
Essential Safety Equipment
SRS Air Bags
2-51
Mazda6_8Z64-EA-08H_Edition1 Page63
Wednesday, June 25 2008 10:3 AM
Form No.8Z64-EA-08H

Black plate (71,1)
3Knowing Your Mazda
Explanation of basic operations and controls; opening/closing and adjustment
of various parts.
Advanced Keyless Entry and Start System ................................ 3-2Advanced Keysí...................................................................... 3-2
Operation Using Advanced Keyless Functions ......................... 3-7
Operation Using Advanced Key Functions ............................. 3-16
Advanced Key Suspend Function ........................................... 3-19
Warning Lights and Beep Sounds ........................................... 3-19
When Warning Indicator/Beep is Activated ............................ 3-22
Doors and Locks ......................................................................... 3-23 Keys ........................................................................................ 3-23
Keyless Entry System
í.......................................................... 3-24
Door Locks ............................................................................. 3-29
Trunk Lid ................................................................................ 3-33
Inside Trunk Release Lever ..................................................... 3-36
Power Windows ...................................................................... 3-37
Fuel-Filler Lid and Cap ........................................................... 3-44
Hood ....................................................................................... 3-46
Moonroof
í............................................................................. 3-47
Security System ........................................................................... 3-50 Immobilizer System (with Advanced Key) ............................. 3-50
Immobilizer System (without Advanced Key) ........................ 3-53
Theft-Deterrent System
í........................................................ 3-55
Steering Wheel and Mirrors ...................................................... 3-59 Steering Wheel ........................................................................ 3-59
Mirrors .................................................................................... 3-59
3-1íSome models.
Mazda6_8Z64-EA-08H_Edition1 Page71
Wednesday, June 25 2008 10:3 AM
Form No.8Z64-EA-08H

Black plate (78,1)
NOTElThe trunk is out of the operational range,
however, starting the engine may be
possible.
lThe engine may not start if the advanced
key is placed in the following areas:
lAround the dashboardlIn the storage compartments such as the
glove box
lOn the rear parcel shelflStarting the engine may be possible even if
the advanced key is outside of the vehicle
and extremely close to a door and window,
however, always start the engine from the
driver's seat.
If the vehicle is started and driven away
while the advanced key is not in the vehicle,
the vehicle will not restart after it is turned
off and the push button start will switch off.
lIf the advanced key is detected within
operational range, the operation indicator
light on the transmitter flashes
momentarily.
qLocking, Unlocking Doors
To lock
All the doors can be locked by pressing
the request switch on either front door
while the advanced key is being carried.
A beep sound will be heard once and the
hazard warning lights will flash once.
Request switch
NOTElThe request switch on driver's door can be
used to close the power windows, refer to
Opening/Closing Power Windows from
Outside (page 3-41).
lConfirm that all the doors are securely
locked.
lAll the doors cannot be locked when any
door is open.
lIf your vehicle has a theft-deterrent system,
the hazard warning lights only flash when
the system is armed.
Refer to the theft-deterrent system on page
3-55.
lA beep sound is heard for confirmation
when the doors are locked using the request
switch. If you prefer, the beep sound can be
turned off.
The volume of the beep sound can also be
changed.
Refer to Personalization Features on page
10-8.
lThe setting can be changed so that the
doors are locked automatically without
pressing the request switch when walking
away from the vehicle (page 10-8).
(Auto-lock function)
Three seconds after the doors and the trunk
lid are closed and the advanced key is out
of the operational range, the doors will lock
automatically. Also, the hazard warning
lights flash once. (Even if the driver is in
the operational range, all doors are locked
automatically after about 30 seconds.)
If you are out of the operational range
before the doors are completely closed or
another advanced key is left in the vehicle,
the auto-lock function will not work.
Always make sure that all doors are closed
and locked before leaving the vehicle.
The auto-lock function does not close the
power windows or moonroof.
3-8
Knowing Your Mazda
Advanced Keyless Entry and Start System
Mazda6_8Z64-EA-08H_Edition1 Page78
Wednesday, June 25 2008 10:3 AM
Form No.8Z64-EA-08H

Black plate (79,1)
To unlock
Driver's door handle
To unlock the driver's door, touch the
sensor area on the inside of the driver's
door handle. A beep sound will be heard
twice and the hazard warning lights will
flash twice.
After unlocking the driver's door, unlock
all the other doors by pressing the door-
lock switch on the inside of the driver's
door.
Front passenger door handle
To unlock the doors, touch the sensor area
on the inside of a front passenger door
handle. A beep sound will be heard twice
and the hazard warning lights will flash
twice.
NOTElThe doors cannot be unlocked for about
three seconds after they are locked even if
the sensor area on the inside of either front
door handle is touched.
lGrasp either front door handle properly to
unlock the doors, and make sure it is
unlocked before opening it.
If the door handle is pulled before the door
is unlocked, the door may not open. If this
happens, lock the door and securely grasp
the door handle again to confirm that the
door is unlocked, then open the door.
lThe sensor is installed on the inside of the
front door handles. The doors cannot be
unlocked by touching any area other than
the sensor area.
lIf you grasp a front door handle while
wearing gloves, the doors may not unlock,
or they could require extra time to unlock.
lThe doors could unlock if someone is
carrying the advanced key near the front
door handle and the front door handle is
splashed with water such as by rain, or by
a car wash.
lIf your vehicle has a theft-deterrent system,
the hazard warning lights only flash when
the system is turned off.
Refer to the theft-deterrent system on page
3-55.
lThe system can be set to unlock all doors by
performing a single operation.
Refer to Personalization Features on page
10-8.
lA beep sound is heard for confirmation
when the doors are unlocked using a door
handle. If you prefer, the beep sound can be
turned off.
The volume of the beep sound can also be
adjusted.
Refer to Personalization Features on page
10-8.
Knowing Your Mazda
Advanced Keyless Entry and Start System
3-9
Mazda6_8Z64-EA-08H_Edition1 Page79
Wednesday, June 25 2008 10:3 AM
Form No.8Z64-EA-08H

Black plate (81,1)
Ignition positions
Each time the push button start is pressed,
the ignition switches in the order of off,
ACC, and ON. Pressing the push button
start again from ON switches the ignition
off.
Indicator light
Indicator
light (ACC) Indicator
light (ON)
NOTElThe order in which the ignition is switched
can be changed.
Refer to Personalization Features on page
10-8.
lThe engine starts by pressing the push
button start while depressing the clutch
pedal (manual transaxle) or the brake
pedal (automatic transaxle). To switch the
ignition position, press the push button start
without depressing the pedal.
lDo not leave the ignition switched ON
while the engine is not running. Doing so
could result in the battery going dead. If the
ignition is left in ACC (For automatic
transaxle, the shift lever is in the P position,
and the ignition is in ACC), the ignition
switches off automatically after one hour.
The setting can be changed to not switch
the ignition off automatically.
Refer to Personalization Features on page
10-8.
Off
The steering wheel locks to help protect
against theft. Also, the power supply to
electrical devices is turned off.
The push button start indicator lights
(ACC and ON) turn off.
WARNING
Before leaving the driver's seat, always
switch the ignition off, set the parking
brake, and make sure the shift lever is
in P (automatic transaxle) or in 1st gear
or R (manual transaxle):
Leaving the driver's seat without
switching off the ignition, setting the
parking brake, and shifting the shift
lever to P (automatic transaxle) or to
1st gear or R (manual transaxle) is
dangerous. Unexpected vehicle
movement could occur which could
result in an accident.
In addition, if your intention is to
leave the vehicle for even a short
period, it is important to switch the
ignition off, as leaving it in another
position will disable some of the
vehicle's security systems and run the
battery down.
ACC (Accessory)
The steering wheel unlocks and some
electrical accessories will operate.
The indicator light (ACC) illuminates.
NOTE
The advanced keyless entry system does not
function while the push button start has been
pressed to ACC, and the doors will not lock/
unlock even if they have been locked manually.
Knowing Your Mazda
Advanced Keyless Entry and Start System
3-11
Mazda6_8Z64-EA-08H_Edition1 Page81
Wednesday, June 25 2008 10:3 AM
Form No.8Z64-EA-08H