change time MAZDA MODEL 6 2016 Owners Manual (in English)

Black plate (3,1)
Thank you for choosing a Mazda. We at Mazda design and build vehicles with complete
customer satisfaction in mind.
To help ensure enjoyable and trouble-free operation of your Mazda, read this manual
carefully and follow its recommendations.
An Authorized Mazda Dealer knows your vehicle best. So when maintenance or service is
necessary, that's the place to go.
Our nationwide network of Mazda professionals is dedicated to providing you with the best
possible service.
We assure you that all of us at Mazda have an ongoing interest in your motoring pleasure
and in your full satisfaction with your Mazda product.
Mazda Motor Corporation
HIROSHIMA, JAPAN
Important Notes About This Manual
Keep this manual in the glove box as a handy reference for the safe and enjoyable use of your Mazda. Should you
resell the vehicle, leave this manual with it for the next owner.
All specifications and descriptions are accurate at the time of printing. Because improvement is a constant goal at
Mazda, we reserve the right to make changes in specifications at any time without notice and without obligation.
Air Conditioning and the Environment
Your Mazda's genuine air conditioner is filled with a refrigerant that has been found not to damage the earth's
ozone layer. If the air conditioner does not operate properly, consult an Authorized Mazda Dealer.
Perchlorate
Certain components of this vehicle such as [air bag modules, seat belt pretensioners, lithium batteries, ···] may contain Perchlorate Material- - Special handling
may apply for service or vehicle end of life disposal. See
www.dtsc.ca.gov/hazardouswaste/perchlorate.
Please be aware that this manual applies to all models, equipment and options. As a result, you may find
some explanations for equipment not installed on your vehicle.
©2014 Mazda Motor Corporation
Feb. 2015 (Print2)
A Word to Mazda Owners
Mazda6_8EA2-EA-14K_Edition2 Page3
Saturday, January 10 2015 3:24 PM
Form No.8EA2-EA-14K

Black plate (19,1)
qSeat Warmerí
The seats are electrically heated. The
ignition must be switched ON.
Press the seat warmer switch to illuminate
the indicator light while the ignition is
switched ON. The mode changes as
follow each time the seat warmer switch is
pressed.
Front
OFF
High
Mid
Low
Rearí
OFF
High
Mid
Low
WARNING
Be careful when using the seat warmer:
The heat from the seat warmer may
be too hot for some people, as
indicated below, and could cause a
low-temperature burn.
ØInfants, small babies, elderly
people, and physically challenged
people
ØPeople with delicate skin
ØPeople who are excessively
fatigued
ØPeople who are intoxicated
ØPeople who have taken sleep-
inducing medicine such as
sleeping pills or cold medicine
Do not use the seat warmer with
anything having high moisture-
retention ability such as a blanket or
cushion on the seat:
The seat may be heated excessively
and cause a low-temperature burn.
Do not use the seat warmer even when
taking a short nap in the vehicle:
The seat may be heated excessively
and cause a low-temperature burn.
Do not place heavy objects with sharp
projections on the seat, or insert
needles or pins into it:
This could cause the seat to become
excessively heated and result in injury
from a minor burn.
Essential Safety Equipment
Seats
2-7íSome models. Mazda6_8EA2-EA-14K_Edition2 Page19
Saturday, January 10 2015 3:24 PM
Form No.8EA2-EA-14K

Black plate (79,1)
qTransmitter
Operation buttons Operation indicator light
NOTEl(With theft-deterrent system)
The hazard warning lights flash when the
theft-deterrent system is armed or turned
off.
Refer to Theft-Deterrent System on page
3-41.
l(With the advanced keyless function)
A beep sound can be heard for confirmation
when the doors are locked/unlocked using
the key. If you prefer, the beep sound can be
turned off.
The volume of the beep sound can also be
changed.
Refer to Personalization Features on page
9-9.
Use the following procedure to change the
setting.
1. Switch the ignition off and close all of the
doors and the trunk lid.
2. Open the driver's door.3. Within 30 seconds of opening the driver's
door, press and hold the LOCK button on
the key for 5 seconds or longer.
All of the doors lock and the beep sound
activates at the currently set volume. (If the
beep sound is currently set to not activate, it
will not activate.) The setting changes each
time the LOCK button on the key is pressed
and the beep sound activates at the set
volume. (If the beep sound has been set to
not activate, it will not activate.)
4. The setting change is completed by doing
any one of the following:
lSwitch the ignition to ACC or ON.lClose the driver's door.lOpen the trunk lid.lThe key is not operated for 10 seconds.lPress any button except the LOCK
button on the key.
lA request switch is pressed.
The operation indicator light flashes when
the buttons are pressed.
Lock button
To lock the doors, press the lock button
and the hazard warning lights will flash
once.
(With the advanced keyless function)
A beep sound will be heard once.
To confirm that all doors have been
locked, press the lock button again within
5 seconds. If they are closed and locked,
the horn will sound.
Before Driving
Keys
3-5
Mazda6_8EA2-EA-14K_Edition2 Page79
Saturday, January 10 2015 3:24 PM
Form No.8EA2-EA-14K

Black plate (80,1)
NOTElThe doors can be locked by pressing the
lock button while any other door or the
trunk lid is open. The hazard warning lights
will not flash.
When the lock button is pressed while any
door is open and then the door is closed, all
the doors are locked.
lConfirm that all doors are locked visually
or audibly by use of the double click.
lMake sure all doors are locked after
pressing the button.
l(With theft-deterrent system)
When the doors are locked by pressing the
lock button on the key while the theft-
deterrent system is armed, the hazard
warning lights will flash once to indicate
that the system is armed.
Unlock button
To unlock the driver's door, press the
unlock button and the hazard warning
lights will flash twice.
(With the advanced keyless function)
A beep sound will be heard twice.
To unlock all doors, press the unlock
button again within 3 seconds and two
more beep sounds will be heard.
NOTElThe system can be set to unlock all doors by
performing a single operation.
Refer to Personalization Features on page
9-9.
Use the following procedure to change the
setting.
1. Switch the ignition off and close all of the
doors and the trunk lid.
2. Open the driver's door.
3. Within 30 seconds of opening the driver's
door, press and hold the UNLOCK button
on the key for 5 seconds or longer. The
sound of the doors locking/unlocking can
be heard.
After this, the system switches the setting
each time the UNLOCK button is pressed
(the sound of the doors locking/unlocking
can be heard).
4. The setting change is completed by doing
any one of the following:
lSwitch the ignition to ACC or ON.lClose the driver's door.lOpen the trunk lid.lThe key is not operated for 10 seconds.lPress any button except the UNLOCK
button on the key.
lA request switch is pressed.l(Auto re-lock function)
After unlocking with the key, all doors will
automatically lock if any of the following
operations are not performed within about
60 seconds. If your vehicle has a theft-
deterrent system, the hazard warning lights
will flash for confirmation.
The time required for the doors to lock
automatically can be changed.
Refer to Personalization Features on page
9-9.
lA door or the trunk lid is opened.lThe push button start is switched to any
position other than off.
3-6
Before Driving
Keys
Mazda6_8EA2-EA-14K_Edition2 Page80
Saturday, January 10 2015 3:24 PM
Form No.8EA2-EA-14K

Black plate (87,1)
qLocking, Unlocking with Request
Switch (With the advanced
keyless function)
All doors can be locked/unlocked by
pressing the request switch on the front
doors while the key is being carried.
Front doors
Request switch
To lock
To lock the doors, press the request switch
and the hazard warning lights will flash
once.
A beep sound will be heard once.
To unlock
Driver's door request switch
To unlock the driver's door, press the
request switch. A beep sound will be
heard twice and the hazard warning lights
will flash twice.
To unlock all doors, press the request
switch again within 3 seconds and two
more beep sounds will be heard.
Front passenger door request switch
To unlock all doors, press the request
switch. A beep sound will be heard twice
and the hazard warning lights will flash
twice.NOTE
lThe system can be set to unlock all doors by
performing a single operation.
Refer to Personalization Features on page
9-9.
Use the following procedure to change the
setting.
1. Switch the ignition off and close all of the
doors and the trunk lid.
2. Open the driver's door.
3. Within 30 seconds of opening the driver's
door, press and hold the UNLOCK button
on the key for 5 seconds or longer. The
sound of the doors locking/unlocking can
be heard.
After this, the system switches the setting
each time the UNLOCK button is pressed
(the sound of the doors locking/unlocking
can be heard).
4. The setting change is completed by doing
any one of the following:
lSwitch the ignition to ACC or ON.lClose the driver's door.lOpen the trunk lid.lThe key is not operated for 10 seconds.lPress any button except the UNLOCK
button on the key.
lA request switch is pressed.lConfirm that all doors and the trunk lid are
securely locked.
For the trunk lid, move it without pressing
the electric trunk lid opener to verify that
the trunk lid has not been left ajar.
lAll doors cannot be locked when any door
is open.
lIt may require a few seconds for the doors
to unlock after the request switch is
pressed.
Before Driving
Doors and Locks
3-13
Mazda6_8EA2-EA-14K_Edition2 Page87
Saturday, January 10 2015 3:24 PM
Form No.8EA2-EA-14K

Black plate (88,1)
lA beep sound is heard for confirmation
when the doors are locked/unlocked using
the request switch. If you prefer, the beep
sound can be turned off.
The volume of the beep sound can also be
changed.
Refer to Personalization Features on page
9-9.
Use the following procedure to change the
setting.
1. Switch the ignition off and close all of the
doors and the trunk lid.
2. Open the driver's door.
3. Within 30 seconds of opening the driver's
door, press and hold the LOCK button on
the key for 5 seconds or longer.
All of the doors lock and the beep sound
activates at the currently set volume. (If the
beep sound is currently set to not activate, it
will not activate.) The setting changes each
time the LOCK button on the key is pressed
and the beep sound activates at the set
volume. (If the beep sound has been set to
not activate, it will not activate.)
4. The setting change is completed by doing
any one of the following:
lSwitch the ignition to ACC or ON.lClose the driver's door.lOpen the trunk lid.lThe key is not operated for 10 seconds.lPress any button except the LOCK
button on the key.
lA request switch is pressed.l(With theft-deterrent system)
The hazard warning lights flash when the
theft-deterrent system is armed or turned
off.
Refer to Theft-Deterrent System on page
3-41.
lThe setting can be changed so that the
doors are locked automatically without
pressing the request switch.
Refer to Personalization Features on page
9-9.
(Auto-lock function)
A beep sound is heard when all doors are
closed while the advanced key is being
carried. All doors are locked automatically
after about three seconds when the
advanced key is out of the operational
range. Also, the hazard warning lights flash
once. (Even if the driver is in the
operational range, all doors are locked
automatically after about 30 seconds.) If
you are out of the operational range before
the doors and the trunk lid are completely
closed or another key is left in the vehicle,
the auto-lock function will not work.
Always make sure that all doors and the
trunk lid are closed and locked before
leaving the vehicle. The auto-lock function
does not close the power windows.
l(Auto re-lock function)
After unlocking with the request switch, all
doors will automatically lock if any of the
following operations are not performed
within about 60 seconds. If your vehicle has
a theft-deterrent system, the hazard
warning lights will flash for confirmation.
The time required for the doors to lock
automatically can be changed.
Refer to Personalization Features on page
9-9.
lA door or the trunk lid is opened.lThe ignition is switched to any position
other than off.
3-14
Before Driving
Doors and Locks
Mazda6_8EA2-EA-14K_Edition2 Page88
Saturday, January 10 2015 3:24 PM
Form No.8EA2-EA-14K

Black plate (89,1)
qLocking, Unlocking with Transmitter
All doors can be locked/unlocked by
operating the keyless entry system
transmitter, refer to Keyless Entry System
(page 3-4).
qLocking, Unlocking with Door-
Lock Switch
All doors lock automatically when lock
side is pressed. They all unlock when
unlock side is pressed.
Driver's door
Unlock
Lock
Front passenger's door
UnlockLock
To lock all the doors from an open front
door, press the lock side of the door lock
switch and then close the door.NOTE
When locking the doors this way, be careful
not to leave the key inside the vehicle.
qAuto Lock/Unlock Function
WARNING
lWhen the vehicle speed exceeds 20
km/h (12 mph), all doors lock
automatically.
lWhen the ignition is switched off, all
doors unlock automatically.
These functions can also be disabled so
that they do not operate.
Auto lock/unlock function setting
change using door-lock switch
The doors can set to lock or unlock
automatically by selecting any one of the
functions from the following table and
using the driver's door-lock switch on the
interior door panel to perform the setting
change as indicated in the procedure
which follows.
Settings can be changed using the
following operation.
NOTE
lFunction number 3 is the factory setting for
your vehicle.
lThere are only a total of six auto lock/
unlock settings available for automatic
transaxle vehicles, and three for manual
transaxle vehicles. Be sure to press the
unlock side of the driver's door-lock switch
the correct number of times according to
the selected function number. If the switch
is mistakenly pressed seven times on an
automatic transaxle vehicle or four times
on a manual transaxle, the procedure will
be invalidated. If this occurs, start the
procedure from the beginning.
Before Driving
Doors and Locks
3-15
Mazda6_8EA2-EA-14K_Edition2 Page89
Saturday, January 10 2015 3:24 PM
Form No.8EA2-EA-14K

Black plate (90,1)
Function number Function*1
1The auto door-lock
function is disabled.
2All the doors lock
automatically when the
vehicle speed is about 20
km/h (12 mph) or more.
3All the doors lock
automatically when the
vehicle speed is about 20
km/h (12 mph) or more. All
the doors unlock when the
ignition is switched from
ON to Off.
4(Automatic transaxle
vehicles only)
When the ignition is
switched ON and the shift
lever is shifted from park
(P) to any other gear
position, all the doors lock
automatically.
5(Automatic transaxle
vehicles only)
When the ignition is
switched ON and the shift
lever is shifted from park
(P) to any other gear
position, all the doors lock
automatically.
When the shift lever is
shifted to park (P) while the
ignition is switched ON, all
the doors unlock
automatically.
6(Automatic transaxle
vehicles only)
All the doors lock
automatically when the
vehicle speed is about 20
km/h (12 mph) or more.
When the shift lever is
shifted to park (P) while the
ignition is switched ON, all
the doors unlock
automatically.
*1 Other settings for the auto door lock function are
available at an Authorized Mazda Dealer. For
details consult an Authorized Mazda Dealer.
Refer to Personalization Features on page 9-9.
1. Safely park the vehicle. All doors must
remain closed.
2. Switch the ignition ON.
3. Press and hold the lock side of the
driver's door-lock switch within 20
seconds of switching the ignition ON,
and make sure a beep sound is heard
about eight seconds afterwards.
4. Referring to the auto lock/unlock
function setting table and determine the
function number for the desired setting.
Press the unlock side of the driver's
door-lock switch the same number of
times as the selected function number
(Ex. If you select function 2, press the
unlock side of the switch only 2 times).
5. Three seconds after the function setting
has been changed, a beep sound will
beep in the amount of the selected
function number. (Ex. Function
number 3 = 3 beep sounds)
3-16
Before Driving
Doors and Locks
Mazda6_8EA2-EA-14K_Edition2 Page90
Saturday, January 10 2015 3:24 PM
Form No.8EA2-EA-14K

Black plate (139,1)
(Vehicles with type A audio)
The outside temperature unit can be
switched between Celsius and Fahrenheit
using the following procedure.
1. Press the INFO button with the ignition
switched off and continue pressing the
INFO button for 5 seconds or longer
while switching the ignition ON. The
outside temperature display flashes.
2. Press the up
or downpart of the
INFO switch to change the outside
temperature unit.
3. Press and hold the INFO button for 3
seconds or longer while the outside
temperature display is flashing. The
outside temperature display
illuminates.
qCruise Control Set Vehicle Speed
Display (Type A instrument cluster)
The vehicle speed preset using the cruise
control is displayed.
qMaintenance Monitor (Type A
instrument cluster)
The following maintenance period
notifications can be displayed by turning
the Maintenance Monitor on.
lScheduled Maintenance
lTire RotationlOil Change
For the setting method and indications for
the maintenance monitor, refer to the
Maintenance Monitor.
Refer to Maintenance Monitor on page
6-20.
The maintenance monitor displays the
information when the ignition is switched
ON.
NOTE
This function is inoperable while the vehicle is
being driven.
Message display
When the remaining time or the distance
approaches 0, a message is displayed each
time the ignition is switched ON.
When Driving
Instrument Cluster and Display
4-15
Mazda6_8EA2-EA-14K_Edition2 Page139
Saturday, January 10 2015 3:24 PM
Form No.8EA2-EA-14K

Black plate (182,1)
Lighting Control
qHeadlights
lTurn the headlight switch to turn the headlights, other exterior lights and dashboard
illumination on or off.
lFor vehicles with the type A instrument cluster, check the vehicle condition or have the
vehicle inspected at an Authorized Mazda Dealer according to the indication.
lA system malfunction or operation conditions are indicated by a warning.
Refer to Warning/Indicator Lights on page 4-22.
NOTE
lIf the light switch is left on, the lights will automatically switch off approximately 30 seconds after
switching the ignition off.
The time setting can be changed.
Refer to Personalization Features on page 9-9.
lTo prevent discharging the battery, do not leave the lights on while the engine is off unless safety
requires them.
Without auto-light control
Switch Position
Ignition Position ONACC or
OFFONACC or
OFFONACC or
OFF
Headlights Off Off Off Off On Off
Daytime running lights On
*1Off On*1Off Off Off
Taillights
Parking lights
License lights
Side-marker lights
Dashboard illuminationOff Off On On On Off/On
*2
*1 It turns on while driving the vehicle.
*2 While the lights are turned on, they will remain on even if the ignition is switched to a position other than ON.
If the driver's door is opened or 30 s have elapsed with the lights turned on, the lights turn off.
4-58
When Driving
Switches and Controls
Mazda6_8EA2-EA-14K_Edition2 Page182
Saturday, January 10 2015 3:25 PM
Form No.8EA2-EA-14K