alarm MAZDA MODEL CX-3 2015 Owners Manual (in English)
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2015, Model line: MODEL CX-3, Model: MAZDA MODEL CX-3 2015Pages: 671, PDF Size: 7.03 MB
Page 120 of 671
*Some models.3–42
Before Driving
Security System
Theft-Deterrent System *
If the theft deterrent system detects an
inappropriate entry into the vehicle or
the intrusion sensor detects movement
in the vehicle which could result in the
vehicle (with the intrusion sensor) or its
contents being stolen, the alarm alerts the
surrounding area of an abnormality by
sounding the siren/horn and fl ashing the
hazard warning lights.
The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Intrusion sensor
*
The intrusion sensor uses ultrasonic waves
to detect movement inside the vehicle and
to raise an alert of an intrusion into the
vehicle.
The intrusion sensor detects certain kinds
of movement inside the vehicle, however,
it may also respond to phenomenon
outside the vehicle such as vibrations, loud
noise, wind, and air currents.
CAUTION
In order for the intrusion sensor to
operate appropriately, be aware of the
following:
Do not hang clothing or objects from
a head restraint or a coat hook.
Return the extension sunvisors to
their original positions.
Do not blind the intrusion sensor by
covering it or placing objects over it.
Do not allow the intrusion sensor to
get soiled or wipe it with a liquid.
Do not shock or cause an impact to
the intrusion sensor or the intrusion
sensor bezel.
Do not install seats or seat covers
that are not Mazda genuine products.
To prevent obstruction of intrusion
sensor, do not place objects or cargo
near the intrusion sensor that are
higher than the head restraints.
Intrusion sensor and
intrusion sensor bezel
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 121 of 671
3–43
Before Driving
Security System
Operation
Siren triggering conditions
The siren/horn sounds intermittently and
the hazard warning lights fl ash for about
30 seconds when the system is triggered
by any one of the following:
Unlocking a door with an inside door-
lock knob.
Forcing open a door, the bonnet or the
liftgate.
Opening the bonnet by operating the
bonnet release handle.
Switching the ignition ON without using
the push button start.
(With the intrusion sensor)
The intrusion sensor detects a movement
in the vehicle.
The system will be triggered again (up to
10 times) if one of the above conditions
remains.
(With the intrusion sensor)
Disconnecting the battery terminal (the
hazard warning lights do not fl ash).
The system will be triggered about 10
times.
NOTE
The liftgate does not open while the
theft-deterrent system is operating.
If the battery goes dead while the
theft-deterrent system is armed, the
siren will activate and the hazard
warning lights will fl ash when the
battery is charged or replaced.
How to Arm the System
1. Close the windows securely.
NOTE
(With the intrusion sensor)
Even with a window open, the system
can be armed, however, leaving the
windows even partially open can invite
theft, and wind blowing into the vehicle
could trigger the alarm.
The intrusion sensor function can also
be cancelled.
Refer to Cancelling the Intrusion/Tilt
Sensor on page 3-44 .
2. Switch the ignition OFF.
3. Make sure the bonnet, the doors, and
the liftgate are closed.
4. Press the lock button on the transmitter
or lock the driver's door from the
outside with the auxiliary key.
The hazard warning lights will fl ash
once.
(With the advanced keyless function)
Press a request switch.
The security indicator light in the
instrument panel fl ashes twice per
second for 20 seconds.
5. After 20 seconds, the system is fully
armed.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 122 of 671
*Some models.3–44
Before Driving
Security System
NOTE
The theft deterrent system can also
be armed by activating the auto
relock function with all the doors, the
liftgate and the bonnet closed.
Refer to Transmitter on page 3-4 . The system will disarm if one of
the following operations takes place
within 20 seconds after pressing the
lock button:
Unlocking any door.
Opening any door.
Opening the bonnet.
Switching the ignition ON.
(With the advanced keyless
function)
Pressing the electric liftgate opener
while the key is being carried.
To rearm the system, do the arming
procedure again.
When the doors are locked by
pressing the lock button on the
transmitter or using the auxiliary key
while the theft-deterrent system is
armed, the hazard warning lights will
fl ash once to indicate that the system
is armed.
Cancelling the Intrusion Sensor
(With Intrusion Sensor)
If the theft deterrent system has been
armed while any of the following
conditions are present, cancel the intrusion
sensor to prevent the alarm from triggering
unnecessarily.
(Intrusion sensor)
Leaving the vehicle with a movable
object, passengers or pets remaining
inside.
Leaving an object inside the vehicle
that can roll around, such as when the
vehicle is placed on a tilting, unstable
surface when being shipped.
Hanging small objects/accessories in
the vehicle, hanging clothing on a coat
hook, or placing other items which can
move easily inside the vehicle.
Parking in an area where there is strong
vibration or loud noise.
When using a high pressure or automatic
car wash.
Continuous shock and vibration
from hail or thunder and lightning is
transmitted to the vehicle.
Doors are locked with a window or the
sunroof* left open.
An accessory heater or device that
produces moving air and vibration
operates while the theft deterrent system
is armed.
NOTE
If any door or the liftgate remains closed
for 30 seconds, all the doors and the
liftgate automatically re-lock and the
theft deterrent system arms even if a
window and the sunroof
* is left open.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 123 of 671
3–45
Before Driving
Security System
To cancel the intrusion sensor, press
the intrusion sensor cancel button on
the transmitter within 20 seconds after
pressing the lock button.
The hazard warning lights will fl ash three
times.
NOTE
To reactivate the intrusion sensor,
turn off the armed theft-deterrent
system and then rearm it.
The intrusion sensor is operational
when the theft-deterrent system
is armed. To cancel the intrusion
sensor, press the intrusion sensor
cancel button each time the theft-
deterrent system is armed.
To Turn Off an Armed System
An armed system can be turned off using
any one of the following methods:
Pressing the unlock button on the
transmitter.
Starting the engine with the push button
start.
(With the advanced keyless function)
Pressing a request switch on the doors.
The hazard warning lights will fl ash twice.
NOTE
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned off, the hazard warning
lights will fl ash twice to indicate that the
system is turned off.
To Stop the Alarm
A triggered alarm can be turned off using
any one of the following methods:
Pressing the unlock button on the
transmitter.
Starting the engine with the push button
start.
(With the advanced keyless function)
Pressing a request switch on the doors.
Pressing the electric liftgate opener
while the key is being carried.
The hazard warning lights will fl ash twice.
Theft-Deterrent Labels
A label indicating that your vehicle is
equipped with a Theft-Deterrent System is
in the glove compartment.
Mazda recommends that you affi x it to the
lower rear corner of a front door window.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 171 of 671
*Some models.4–31
When Driving
Instrument Cluster and Display
Cruise Control Set Vehicle Speed
Display*
The vehicle speed preset using the cruise
control is displayed.
Trip Computer and INFO Switch *
The following information can be selected
by pressing the up
or down part of the
INFO switch with the ignition switched
ON.
Approximate distance you can travel on
the available fuel
Average fuel economy
Current fuel economy
Average vehicle speed
Vehicle speed alarm *
If you have any problems with your trip
computer, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
Distance-to-empty mode
This mode displays the approximate
distance you can travel on the remaining
fuel based on the fuel economy.
The distance-to-empty will be calculated
and displayed every second.
(European model)
(Except European model)
NOTE
Even though the distance-to-empty
display may indicate a suffi cient
amount of remaining driving distance
before refuelling is required, refuel
as soon as possible if the fuel level
is very low or the low fuel warning
light illuminates.
The display may not change unless
you add more than approximately 9 L
(2.3 US gal, 1.9 Imp gal) of fuel.
The distance-to-empty is the
approximate remaining distance
the vehicle can be driven until all
the graduation marks in the fuel
gauge (indicating the remaining fuel
supply) disappear.
If there is no past fuel economy
information such as after fi rst
purchasing your vehicle or the
information is deleted when the
battery leads are disconnected, the
actual distance-to empty/range may
differ from the amount indicated.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 172 of 671
*Some models.4–32
When Driving
Instrument Cluster and Display
Average fuel economy mode
This mode displays the average fuel
economy by calculating the total fuel
consumption and the total travelled
distance since purchasing the vehicle, re-
connecting the battery after disconnection,
or resetting the data. The average fuel
economy is calculated and displayed every
minute.
(European model)
(Except European model)
To clear the data being displayed, press the
INFO button for more than 1.5 seconds.
After pressing the INFO button, - - - L/100
km (- - - mpg) will be displayed for about
1 minute before the fuel economy is
recalculated and displayed.
Current fuel economy mode
This mode displays the current fuel
economy by calculating the amount of fuel
consumption and the distance travelled.
Current fuel economy will be calculated
and displayed every 2 seconds.
(European model)
(Except European model)
When you've slowed to about 5 km/h (3
mph), - - - L/100 km (- - - mpg) will be
displayed.
Average vehicle speed mode
This mode displays the average vehicle
speed by calculating the distance and the
time travelled since connecting the battery
or resetting the data.
Average vehicle speed will be calculated
and displayed every 10 seconds.
(European model)
(Except European model)
To clear the data being displayed, press the
INFO button for more than 1.5 seconds.
After pressing the INFO button, - - - km/h
(- - - mph) will be displayed for about
1 minute before the vehicle speed is
recalculated and displayed.
Vehicle speed alarm mode
*
In this mode, the current setting for the
vehicle speed alarm is displayed. You can
change the vehicle speed setting at which
the warning is triggered.
NOTE
The vehicle speed alarm display is
activated at the same time the beep
sound is heard. The set vehicle speed
fl ashes several times.
The vehicle speed alarm can be set using
the INFO switch.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 173 of 671
4–33
When Driving
Instrument Cluster and Display
NOTE
Always set the vehicle speed
according to the laws and regulations
of the country/city in which the
vehicle is driven. In addition, always
verify the speed of the vehicle using
the speedometer.
The vehicle speed alarm function can
be set between 30 and 250 km/h (20
and 150 mph).
The vehicle speed alarm can be set using
the following procedure.
1. Press the INFO switch on the speed
alarm screen.
2. Press the INFO button until the beep
sounds.
3. Press the up
or down part of the
INFO switch to select the desired
vehicle speed.
4. Press the INFO button until the beep
sounds.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 358 of 671
5–36
Interior Features
Audio System
(To scan for programme-type
information:)
1. Press the Programme-type information
button (
,) when the programme-
type code is displayed.
2. Press the Programme-type information
button (
,) until the beep sounds.
The unit will scan for broadcasts, if
none are found, “ Nothing ” will be
displayed and the unit will return to the
previously tuned band.
(To store programme types in the
channel preset buttons:)
1. Press the Programme-type information
button (
,) when the programme-
type code is displayed.
2. Press the Programme-type information
button (
,) and select the programme
type.
3. While the programme type is displayed,
press a channel preset button for about
2 seconds.
Emergency broadcast
If an emergency broadcast is received,
the emergency broadcast intercedes even
while using other functions (FM, CD,
USB, iPod, AUX, or BT audio), and
“ Alarm! ” is displayed.
When the emergency broadcast ends, the
system will return to the previous mode.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 598 of 671
*Some models.7–52
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Key Left-in-luggage Compartment
Warning Beep (With the advanced
keyless function)
If the key is left in the luggage
compartment with all doors locked
and the liftgate closed, a beep sound is
heard for about 10 seconds to remind
the driver the key has been left in the
luggage compartment. If this happens,
open the liftgate by pressing the electric
liftgate opener and remove the key. A key
removed from the luggage compartment
may not function because its functions
may have been temporarily suspended.
To restore the key function, perform the
applicable procedure (page 3-7 ).
Key Left-in-vehicle Warning Beep
(With the advanced keyless
function)
If a key is left in the vehicle cabin and all
the doors and the luggage compartment
are locked using a separate key, a beep
sound is heard for about 10 seconds to
remind the driver that the key has been
left in the vehicle cabin. If this happens,
open the door and remove the key. A key
removed from the vehicle this way may
not function because its functions may
have been temporarily suspended. Perform
the applicable procedure to restore the
functions of the key (page 3-7 ).
i-stop Warning Beep *
If the driver's door is opened while
engine idling is stopped, the warning
sound operates to notify the driver that
engine idling is stopped. It stops when
the driver's door is closed.
The warning sound operates if the
following operations are performed
while the engine idling is stopped. In
such cases, the engine does not restart
automatically to ensure safety. Start the
engine using the normal method.
(European model)
The driver's seat belt is unfastened and
the driver's door is opened.
(Except European model)
(Manual transaxle)
With the shift lever in a position other
than neutral, the driver's seat belt is
unfastened and the driver's door is
opened.
(Automatic transaxle)
With the selector lever in the D or
M (not in second gear fi xed mode)
position, the driver's seat belt is
unfastened and the driver's door is
opened.
Vehicle Speed Alarm *
The vehicle speed alarm function is
designed to alarm the driver via a single
beep sound and a warning indication in the
instrument cluster that the previously set
vehicle speed has been exceeded.
You can change the vehicle speed setting
at which the warning is triggered (page
4-31 ).
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 605 of 671
8–3
Customer Information
Warranty
Add-On Non-Genuine Parts and Accessories
Please note that technical alterations to the original state of your Mazda vehicle can affect
the safety of the vehicle. Such technical alterations include not only the use of unsuitable
spare parts, but also accessories, fi ttings or attachments, including rims and tyres.
Genuine Mazda Parts and Genuine Mazda Accessories have been specifi cally designed for
Mazda vehicles.
Other parts and accessories than those mentioned above have not been examined and
approved by Mazda unless explicitly stated by Mazda. We cannot certify the suitability of
such products. Mazda is not liable for any damage caused by the use of such products.
WARNING
Be very careful in choosing and installing add-on electrical equipment, such as mobile
telephones, two-way radios, stereo systems, and car alarm systems:
Incorrectly choosing or installing improper add-on equipment or choosing an improper
installer is dangerous. Essential systems could be damaged, causing engine stalling,
air-bag (SRS) activation, ABS/TCS/DSC inactivation, or a fi re in the vehicle.
Mazda assumes no responsibility for death, injury, or expenses that may result from the
installation of add-on non-genuine parts or accessories.
$ 9 @ & ; & & % @ & E J U J P O J O E C