sensor MAZDA MODEL CX-3 2018 Smart Start Guide (in English)

2 MAZDAUSA.COM
A
B
DRIVER’\f VIEW
DI
G
H
F
E
J
R
C
1 This indicator light turns on to remind you that the front
passenger's front/side airbags and seat belt pretensioner will not
deploy during a collision. The reason for this is that the sensor has
determined that an adult is not sitting in the front passenger seat.
NOTE: If a smaller adult sits on the front passenger seat, the sensors
2940109_18b CX-3 SSG_060817.indd 26/8/17 2:37 PM

20 MAZDAUSA.COM
MAZDA RADAR CRUISE CONTROL (MRCC) SYSTEM
The MRCC system maintains vehicle speed and f\Xollowing distance using a radar sensor
to detect a vehicle ahead. The driver simply presets the vehicle speed between 19 mph
and 90 mph and the\X system will maintain a safe following distance without having to turn the cruise control off.
SETTING THE MRCC:
When the MODE switch is pushed, the
vehicle speed and t\.he distance between
vehicles while in headway control can be
set. The MR\b\b indication is shown in the
Active Driving Display.
NOTE: The radar for the MR\b\b is located
behind the Mazda emblem in the g\.rille.
Keep this area clean to avoid the system
not working properly.
How to set the speed:
1 Adjust the vehicle to the desired speed using the\. accelerator pedal.
2
Push the \fET + or \f\.ET – switch. The set speed and the in\.ter-vehicle distance display
filled with white lines are displayed in the Active Driving Display and the MR\b\b indicator light (green) turns on simultaneously.
MAZDA RADAR \bRUI\fE \bONTROL
(IF EQUIPPED)
OPERATION MODES
MODE DISPLAY
\bonstant \fpeed
Headway \bontrol
MRCC
WARNING:
MR\b\b shuts off
when it reaches the low mph limit.
The vehicle will not brake/stop by itself. \fwitch the
MR\b\b system off
when not in use.
Vehicle ahead
MRCC distance
between vehicles
Active Driving Display
MRCC set
vehicle speed
2940109_18b CX-3 SSG_060817.indd 206/8/17 2:39 PM

m{zd{ c x-3 23
SMART BRAKE SUPPORT (SBS)
At speeds of 10 mph or higher\X, the SBS alerts the driver of a possible collision and attempts to reduce the severity of an imminent collision with the \Xvehicle ahead. SBS operates when the
vehicle is traveling at speeds hi\Xgher than the range of the SMART CITY BRAKE SUPPORT (SCBS).
Partial list of operating conditions: •
During vehicle speeds of 10 mph or higher\..
•
The \fB\f system has not been turned off.
\fB\f system can be turned off using \fafety \fettings in MAZDA \bONNE\bT (p. 10).
Refer to your Owner’s Manual for a complete list of \fB\f operating
conditions and system details.
COLLISION WARNING
If there is the possibility of a collision with a vehicle ahead, the beep sounds continuously and a warning is indicated in the
multi-information display.
Forward Sensing
Camera
Radar sensor
\fMART BRAKE \fUPPORT
(IF EQUIPPED)
WARNING:
\fB\f is only a
supplementary
system to reduce
damage in
the event of a
collision; however,
the \fB\f has
limitations. Do
not rely solely on
the \fB\f. Always
keep your eyes on
the road.
2940109_18b CX-3 SSG_060817.indd 236/8/17 2:39 PM

26 MAZDAUSA.COM
Active Driving Display
DI\fTAN\bE RE\bOGNITION \fUPPORT \fY\fTEM
(IF EQUIPPED)
DISTANCE RECOGNITION SUPPORT SYSTEM (DRSS)
The DRSS measures the distance between your vehicle and a vehicle ahead using
a radar sensor (front) while the vehicle speed is 19\X mph or faster and indicates a recommended distance to maintain between the vehicles. Furthermore, if your vehicle
approaches a vehicle ahead more closely than the appropriate distance to maintain between the vehicles, the vehicle ahead indication in the displ\Xay is illuminated in
amber to advise the driver to keep a safe distance from the vehicle ahead.
DISTANCE\fBETWEEN\fVEHICLES GUIDELINES*
DISPLAY Traveling at 25 mph Traveling at 50 mph
About 32 ft or lessAbout 65 ft or less
*The distance between vehicles differs depending on vehicle speed.
Vehicle
ahead
2940109_18b CX-3 SSG_060817.indd 266/8/17 2:39 PM

28 MAZDAUSA.COM
BLIND SPOT MONITORING (BSM)
The BSM system is designed to assist the driver by monitoring blind spots on the left
and right sides of the vehicle in certain situations, such as lane chan\Xges.
•
The B\fM detects vehicles approaching from the rear while traveling in
the forward direction at a speed \.of 6.3 mph or more and notifies the
driver by turning on the B\fM w\.arning indicator light and displaying the vehicle detection screen (vehicles with Active Driving Display).
•
If the turn signal lever is operated to signal a turn in the direction
in which the B\fM warning indicator light is illuminated while the
approaching vehicle is detected, the B\fM warns the driver by turning on the B\fM warning indicator light, and by activating the warning sound and
the warning screen indicator display
(vehicles with Active Driving Display).
•
The detection area on this system
covers the driving lane\.s on both sides
of the vehicle and from the rear part
of the front doors to about 164 ft behind the vehicle.
• B\fM sensors are located under the
left and right rear bumper areas.
The B\fM system may not operate properly if the rear bumper is dirty,
so keep the rear bumper area clean
and free of bumper stickers.
NOTE:
•
The B\fM can assist the driver in confirming the safety
of the surroundings, but is not a complete substitute.
•
The driver is responsible for ensuring safe lane changes
and other maneuvers.
•
Always pay attention to the direction in which th\.e vehicle
is traveling and the vehicle’s surroundings.
Turning BSM System Off:
Turning the B\fM system off will turn off both the light and sound indicators. To turn the B\fM system off, push the B\fM OFF \.switch on the dash.
The B\fM OFF indicator in the instrument cluster will turn on to indicate the B\fM system is off.
NOTE: Turning the B\fM system off will also turn off the Rear \bross Traffic Alert system.
BLIND \fPOT MONITORING \fY\fTEM
WARNING:
B\fM is only a
supplementary
system to help
aid in monitoring
blind spots;
however, B\fM
has limitations.
The system may
not detect all
vehicles, especially
a motorcycle. Do
not rely solely on
the B\fM. Relying
solely on the
B\fM may cause
an unexpected
accident resulting
in death or serious
injury. Make sure
to look over your
shoulder before
changing lanes.
Your
vehicle
Detection areas
ACTIVE DRIVING DISPLA\XY
WHITE Vehicle
Detected
AMBER Vehicle
Detected
with Turn
\fignal On
BSM switch
2940109_18b CX-3 SSG_060817.indd 286/8/17 2:39 PM

m{zd{ c x-3 29
REAR \bRO\f\f TRAFFI\b ALERT
(IF EQUIPPED)
REAR CROSS TRAFFIC ALERT (RCTA)
The RCTA is designed to alert the driver of oncoming traffic when backing out of a parking spot. RCTA is active when the vehicle is in reverse and the vehicle speed is between 0 mph and 6 mp\Xh.
When the B\fM sensors detect a moving object, the R\bTA will notify the driver with indicators and sound:
• Rear view monitor and outside mirror flashing indications.
Refer to your Owner’s Manual for complete details.
WARNING:
R\bTA is only a
supplementary
system to help aid
when backing up; however, R\bTA
has limitations.
The system does not detect all
vehicles, especially motorcycles. Do
not rely solely on the R\bTA. Relying
solely on the R\bTA may cause
an unexpected
accident resulting in serious injury.
Always back up slowly.
BSM/RCTA (Left)BSM/RCTA (Right)
Rear view monitor
Object
detected
Object
detected
2940109_18b CX-3 SSG_060817.indd 296/8/17 2:39 PM

30 MAZDAUSA.COM
Pull to
flash
high
beams Push for
high beams
LIGHTING / TURN \fIG\.NAL\f
LIGHTING CONTROL / TURN SIGNAL LEVER
NOTE:
The Daytime Running Lights (DRL) automatically turn on when the ig\.nition is
switched ON. To disable/enable this feature, see your Authorized Mazda Dealer.
NOTE: You can adjust the timing of the Auto Headlights OFF and the sensitivity of the
Auto Light \bontrol. \fee MAZDA \bONNE\bT \fettings (p. 10).
(IF EQUIPPED)
The light sensor automatically determines when to turn the headlights on or off.
Turns tail, parking, dashboard, and headlights on.
THREE-FLASH SIGNAL
To signal a lane ch\.ange, push the turn signal lever up or down halfway and
release. The turn signal indicator will only flash \.three
times. \fee "Personalization
Features" to activate.
Turns fog lights on only when headlights are on.
Turns tail, parking, and dashboard lights on.
Lighting
control/turn signal lever
2940109_18b CX-3 SSG_060817.indd 306/8/17 2:39 PM

m{zd{ c x-3 31
Pull to
dispense
windshield
washer fluidMISTAUTO
LO
HI
12
3
WIPER / WA\fHER \bONTROL
CAUTION:
If the ignition is\. ON, turn
the AUTO wipers OFF
when going through a car
wash or while cleaning or touching the windsh\.ield.
WINDSHIELD WIPER / WASHER CONTROL LEVER
(IF EQUIPPED)
The rain sensor senses the amount of rainfall and
turns the wipers on or off.
Rotating the inner ri\.ng
clockwise (away from you)
creates greater wiper sensitivity and makes the
wipers move faster. The + position increases wiper
speed. Rotating the inner ring counterclockwise
(toward you) makes the wipers move
slower. The - position
decreases wiper speed.
Normal speed
Intermittent
REAR WINDOW
WIPER/WASHER
(hold as desired)
NOTE: Vehicles not equipped with AUTO wipers will have
INT wipers. \fet the lever to INT and choose an interval timing by rotating the ring between fast and slow.
Windshield
wiper/washer
control lever
2940109_18b CX-3 SSG_060817.indd 316/8/17 2:40 PM