light MAZDA MODEL CX-30 2019 (in English) Owner's Guide

Locking
Unlocking
xThe system may not operate normally
under the following conditions.
xYou touch the sensing area of the
door lock touch sensor and the
sensing area of the door release
touch sensor at the same time.
xYou touch the sensing area of the
touch sensor while wearing gloves.
xForeign matter such as snow or dirt
is stuck on the sensing area of the
touch sensor.
xYou pull the door handle just after
touching the sensing area of the
touch sensor.
xThe system may operate if the outer
side door handle of a front door is
splashed with water by a car wash or
rain while the transmitter is in the
operation range.
xIf the system does not operate even
though you touch the sensing area of
the touch sensor correctly, release
the touch sensor once, and then
touch the sensing area of the touch
sensor again after waiting about 3
seconds.
Locking
When locking , touch the sensing area
of the door lock touch sensor with all
of the following conditions met.
xThe ignition is switched OFF.xAll the doors are closed.xYou are carrying the transmitter.
The following locations are locked by
touching the sensing area of the door
lock touch sensor.
xAll doorsxFuel-filler flapxLiftgate
When locking , the hazard warning
lights operate one time.
(Except European models)
A beep sound operate one time.
Unlocking
When unlocking , touch the sensing
area of the door release touch sensor
with all of the following conditions
met.
xThe ignition is switched OFF.xThe driver’s door is locked.xThree seconds or longer have passed
since the doors were locked.
xYou are carrying the transmitter.
Ty p e A
(Unlocking from the driver's door)
The following locations are unlocked
by touching the sensing area of the
door release touch sensor of the
driver's door.
Before Driving
Doors and Locks
3-14

xDriver’s doorxFuel-filler flap
NOTE
xThe location to be unlocked can be
changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When unlocking, the hazard warning
lights operate two times.
(Except European models)
A beep sound operate two times.

(Unlocking from the front passenger’s
door)
The following locations are unlocked
by touching the sensing area of the
door release touch sensor of the front
passenger's door.
xAll doorsxFuel-filler flapxLiftgate
When unlocking, the hazard warning
lights operate two times.
(Except European models)
A beep sound operate two times.
Ty p e B
The following locations are unlocked
by touching the sensing area of the
door release touch sensor.
xAll doorsxFuel-filler flapxLiftgate
NOTE
x(With 2-step unlocking function)
The location to be unlocked can be
changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When unlocking, the hazard warning
lights operate two times.
(Except European models)
A beep sound operate two times.
NOTE
xConfirm that all the doors and
liftgate are securely locked.
For the liftgate, move it without
pressing the electric liftgate opener
to verify that the liftgate has not been
left ajar.
x(European models)
The setting can be changed so that a
beep sound is heard for confirmation
when the doors, fuel-filler flap, and
liftgate are locked/unlocked using a
touch sensor.
(Except European models)
A beep sound is heard for
confirmation when the doors,
fuel-filler flap, and liftgate are
locked/unlocked using the touch
sensor. If you prefer, the beep sound
can be turned off.
The volume of the beep sound can
also be changed. Refer to the
Settings section in the Mazda
Connect Owner's Manual.
x(With theft-deterrent system)
The hazard warning lights flash when
the theft-deterrent system is armed
or turned off.
Refer to Theft-Deterrent System on
page 3-49.
xThe setting can be changed so that
the doors, fuel-filler flap, and liftgate
are locked automatically without
touching the sensing area of the
touch sensor.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
(Walk-away auto lock function)
Before Driving
Doors and Locks
3-15

A beep sound is heard when all
doors and the liftgate are closed
while the transmitter is being carried.
All the doors, fuel-filler flap, and
liftgate are locked automatically
when the transmitter is out of the
operational range. Also, the hazard
warning lights flash once. (Even if the
driver is in the operational range, all
the doors, fuel-filler flap, and liftgate
are locked automatically after about
30 seconds.) If you are out of the
operational range before the doors
and the liftgate are completely
closed or another transmitter is left
in the vehicle, the walk-away auto
lock function will not work. Always
make sure that all doors and the
liftgate are closed and locked before
leaving the vehicle. The walk-away
auto lock function does not close the
power windows.
x(Auto re-lock function)
After unlocking with the touch
sensor, all the doors , fuel-filler flap,
and liftgate will automatically lock if
any of the following operations are
not performed within about 30
seconds.
xOpening a door or the liftgate.xSwitching the ignition to any
position other than off.
If your vehicle has a theft-deterrent
system, the hazard warning lights will
flash for confirmation.
The time required for the doors to
lock automatically can be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼Locking, Unlocking with
Tra n s m i t te r
The following locations can be locked/
unlocked by operating the keyless
entry system transmitter. Refer to
Keyless Entry System (page 3-4).
xAll doorsxFuel-filler flapxLiftgate
▼Locking , Unlocking with
Door-Lock Switch
Door-lock switch on driver’s door
The following locations are locked/
unlocked by pressing the door-lock
switch.
xAll doorsxFuel-filler
flapxLiftgate
1. Unlock
2. Lock
Locking from the outside using the
door-lock switch
When locking from the outside using
the door-lock switch, press the lock
side of the door-lock switch with all of
the following conditions met and then
close all the doors.
xThe ignition is switched OFF.xAny door is open.
NOTE
xTo prevent the transmitter from being
left in the vehicle, make sure that you
carry the transmitter before locking.
Before Driving
Doors and Locks
3-16

(With theft-deterrent system
(European models))
Before the liftgate closes, the hazard
warning lights operate 2 times and a
long beep sound is activated.
When the liftgate closes, the hazard
warning lights operate 1 time.

(With theft-deterrent system (Except
European models))
When locking, a beep sound operates
1 time.
In addition, before the liftgate closes,
the hazard warning lights operate 2
times and a long beep sound is
activated.
When the liftgate closes, the hazard
warning lights operate 1 time.

(Without theft-deterrent system
(European models))
When locking, the hazard warning
lights operate 1 time.
In addition, before the liftgate closes,
the hazard warning lights operate 2
times and a long beep sound is
activated.

(Without theft-deterrent system
(Except European models))
When locking, the hazard warning
lights and a beep sound operate 1
time.
In addition, before the liftgate closes,
the hazard warning lights operate 2
times and a long beep sound is
activated.

For details on the power liftgate
function, refer to Power Liftgate on
page 3-22.

Without power liftgate
When locking using the door-lock
switch, press the door-lock switch withall of the following conditions met and
then close the liftgate.
xYou are carrying the transmitter.xThe ignition is switched OFF.xAll the doors are closed.
(With theft-deterrent system
(European models))
When the liftgate closes, the hazard
warning lights operate 1 time.

(With theft-deterrent system (Except
European models))
When locking , a beep sound operates
1 time.
When the liftgate closes, the hazard
warning lights operate 1 time.

(Without theft-deterrent system
(European models))
When locking , the hazard warning
lights operate 1 time.

(Without theft-deterrent system
(Except European models))
When locking , the hazard warning
lights and a beep sound operate 1
time.
NOTE
xTo prevent the transmitter from being
left in the vehicle, make sure that you
carry the transmitter before locking.
xAfter locking by pressing the
door-lock switch and when the
liftgate is closed with the transmitter
left in the vehicle, the liftgate is
unlocked.
Before Driving
Doors and Locks
3-18

xWhen the liftgate latch is released by
pressing the electric liftgate opener,
the liftgate raises slightly. If the
liftgate is not operated for a certain
period of time, the liftgate cannot be
raised.
To o p e n
Press the electric liftgate opener
again.
To c l o s e
To close the liftgate from its slightly
raised position, open it first by
pressing the electric liftgate opener,
then close it after waiting at least 1
second.
xIf the vehicle battery is dead or there
is a malfunction in the electrical
system and the liftgate cannot be
unlocked, the liftgate can be opened
by performing the emergency
procedure.
Refer to When Liftgate Cannot be
Opened on page 7-73.
Closing the liftgate
Lower the liftgate slowly using the
liftgate grip recess, then push the
liftgate closed using both hands.
Do not slam it. Pull up on the liftgate
to make sure it is secure.
For the power liftgate operation, refer
to Power Liftgate on page 3-22.
WARNING
Do not drive the vehicle with the
liftgate-ajar warning indication
displayed :
Otherwise, the liftgate may open
unexpectedly and result in an accident.
NOTE
Confirm that the liftgate is securely
closed.
Move the liftgate without pressing the
electric liftgate opener to verify that the
liftgate has not been left ajar.
▼Power Liftgate*
The power liftgate opens/closes
electrically by operating the switches in
the vehicle or the buttons on the
keyless entry system transmitter.
WARNING
Be sure to watch the power liftgate as
it opens or closes, and make sure that
it closes completely:
Opening or closing the power liftgate
while not watching it move is
dangerous. Because of unseen
obstacles and the jam-safe feature, a
liftgate may not close completely and,
if left unnoticed, could result in serious
injury or death if an occupant were to
fall out of the vehicle.
Always be sure that the area around
the liftgate is clear before activating it.
Before Driving
Doors and Locks
3-22*Some models.

Operation using the transmitter
When the power liftgate button on the
transmitter is pressed and held for
about 1 second or longer with all of
the following conditions met, the
hazard warning lights flash 2 times, a
beep sound is activated, and the
liftgate automatically opens/closes
fully.
xThe ignition is switched OFF.xThe vehicle is stopped.
Refer to Transmitter on page 3-5.
NOTE
xWhen opening the liftgate by
pressing the power liftgate button on
the transmitter, the liftgate can be
opened even when it is locked.
xIf the power liftgate button on the
transmitter is pressed while the
liftgate is opening/closing
electrically, the beep is activated and
the liftgate stops. When pressing the
power liftgate button again, the
liftgate moves in the reverse
direction.
Operation using switch only for
power liftgate
Operation conditions
Opening the liftgate
If the vehicle has satisfied all the
following operation conditions, the
power liftgate can be opened using the
power function.
xAll doors and the liftgate are
unlocked.
xThe vehicle is stopped.x(Manual transmission)
The ignition is switched to a position
other than ON, or when the parking
brake is applied with the shift lever in
N and the ignition switched ON.
x(Automatic transmission)
The ignition is switched to a position
other than ON, or the selector lever
is in P with the ignition switched ON.
Closing the liftgate
xThe vehicle is stopped.x(Manual transmission)
The ignition is switched to a position
other than ON, or when the parking
brake is applied with the shift lever in
N and the ignition switched ON.
x(Automatic transmission)
The ignition is switched to a position
other than ON, or the selector lever
is in P with the ignition switched ON.
NOTE
If the shift lever/selector lever is shifted
to another position and the vehicle is
moved while the liftgate is opening/
closing automatically, the liftgate
operates as follows:
xWhen the liftgate is opening
A beep sound is activated, and the
liftgate moves in the reverse
direction automatically and closes.
xWhen the liftgate is closing
A beep sound is activated, but the
liftgate continues to close.
Operation from the driver's seat (To
open/close)
Press the power liftgate switch for
about 1 second or longer while the
liftgate is in the fully closed/open
position. The hazard warning lights
Before Driving
Doors and Locks
3-24

flash twice and the liftgate opens/
closes fully after a sound is activated.
Operation from outside (To open)
Press the electric liftgate opener on the
liftgate. The hazard warning lights flash
twice and the liftgate opens
automatically after the beep sound is
heard.
(With the advanced keyless function)
A locked liftgate can also be opened
while the key is being carried.
Operation from outside (To close)
Press the power liftgate close switch
while the liftgate is fully opened. The
hazard warning lights flash twice and
the liftgate closes automatically after
the beep sound is heard.
(With the advanced keyless function)
(Without the advanced keyless
function)
Operation using door-lock switch
(With the advanced keyless function)
When the door-lock switch on the
liftgate is pressed, the liftgate fully
closes automatically after all the doors,
fuel-filler flap, and the liftgate are
locked.
For details such as the operation
conditions, refer to Locking , Unlocking
with Door-Lock Switch on page 3-16.
Automatic open/close stop function
The liftgate can be stopped at a
desired position while it is opening/
closing automatically.
Stopping the liftgate
If any of the following operations is
done while the liftgate is opening/
Before Driving
Doors and Locks
3-25

▼Luggage Compartment
Luggage compartment cover*
WARNING
Do not place anything on top of the
cover:
Placing luggage or other cargo on top
of the luggage compartment cover is
dangerous. During sudden braking or a
collision, the cargo could become a
projectile that could hit and injure
someone. The vehicle has a light
weight luggage compartment cover to
keep the contents of your luggage area
out of sight; it will not retain heavy
objects that are not tied down in an
accident such as a rollover. Tie down
all heavy objects, whether luggage or
cargo, using the tie down hooks.
Make sure luggage and cargo are
secured before driving:
Not securing cargo while driving is
dangerous as it could move or be
crushed during sudden braking or a
collision and cause injury.
CAUTION
¾Make sure the luggage compartment
cover is firmly secured. If it is not
firmly secured, it could unexpectedly
disengage resulting in injury.
The luggage compartment can be
accessed by opening the liftgate when
the straps are attached to the sides of
the liftgate.

Removing the luggage compartment
cover
This cover can be removed for more
room.
1. Remove the straps from the hooks.
2. Press the luggage compartment
cover upward from near the pins
and remove the luggage
compartment cover from the pins.
1. Pin

3. Lift the front end of the luggage
compartment cover and remove it.
Before Driving
Doors and Locks
3-28*Some models.

SCHEDULED MAINTENANCE for the
details.
Refer to Scheduled Maintenance
(Europe) on page 6-3.
Refer to Scheduled Maintenance
(Except Europe) on page 6-6.
CAUTION
¾According to the inspection result of
scheduled maintenance, Mazda
genuine deposit cleaner is to be
used. Neglected deposits in the fuel
system may cause malfunction
indicator light coming on to indicate
an engine malfunction, and if the
vehicle continues to be driven under
this condition, it could result in
problems occurring such as idling
failure and poor acceleration.
¾The Mazda genuine deposit cleaner
is not a guarantee of engine
performance no matter the quality of
the fuel used. When a problem
occurs even though the
specified fuel
is used and the Mazda genuine
deposit cleaner is used according to
the instructions, consult an
Authorised Mazda Dealer.
¾If a deposit cleaner other than the
Mazda genuine product is used, it
could result in damage to the fuel
system or the engine internally;
therefore use only the Mazda
genuine product. Mazda genuine
deposit cleaner: K002 W0 001
¾If cleaning required according to the
inspection result of scheduled
maintenance is not done with the
Mazda genuine deposit cleaner,
repair cost for engine malfunctions
caused by deposits are borne by the
customer.
How to use the cleaner
With the fuel tank full, infuse 1 bottle
of Mazda genuine deposit cleaner
directly into the fuel tank.
NOTE
xInfusing the deposit cleaner when
the fuel tank is full provides the
concentration of cleaner within the
range
effective for removing the
deposits and the best cleaning
results can be obtained by the full
tank of fuel with the infused deposit
cleaner contacting the deposits for a
long period of time until the full tank
of fuel is nearly used up.
▼Fuel Requirements
(SKYACTIV-D
1.8)
The vehicle will operate efficiently on
diesel fuel with specification EN590 or
the equivalent.
CAUTION
¾Never use fuel other than
specification EN590 or the
equivalent for your vehicle. Use of
petrol or paraffin in diesel engines
will result in engine damage.
¾Never add fuel system additives.
Otherwise, the emission control
system could be damaged. Consult
an expert repairer (we recommend
an Authorised Mazda Repairer) for
details.
NOTE
When refuelling , always add at least 10
L (2.6 US gal, 2.2 Imp gal) of fuel.
Before Driving
Fuel and Emission
3-31

Fuel-Filler Flap and Cap
▼Fuel-Filler Flap and Cap
WARNING
When removing the fuel-filler cap,
loosen the cap slightly and wait for
any hissing to stop, then remove it:
Fuel spray is dangerous. Fuel can burn
skin and eyes and cause illness if
ingested. Fuel spray is released when
there is pressure in the fuel tank and
the fuel-filler cap is removed too
quickly.
Before refuelling, stop the engine,
and always keep sparks and flames
away from the filler neck:
Fuel vapour is dangerous. It could be
ignited by sparks or flames causing
serious burns and injuries.
Additionally, use of the incorrect
fuel-filler cap or not using a fuel-filler
cap may result in a fuel leak, which
could result in serious burns or death
in an accident.
Do not continue refuelling after the
fuel pump nozzle shuts off
automatically:
Continuing to add fuel after the fuel
pump nozzle has shut off automatically
is dangerous because
overfilling the
fuel tank may cause fuel overflow or
leakage. Fuel overflow and leakage
could damage the vehicle and if the
fuel ignites it could cause a fire and
explosion resulting in serious injury or
death.
CAUTION
¾Always use only a designated Mazda
fuel-filler cap or an approved
equivalent, available at an expert
repairer (we recommend an
Authorised Mazda Repairer). The
wrong cap can result in a serious
malfunction of the fuel and emission
control systems.
¾When using an automatic car wash
or a high water pressure car washer,
lock the driver's door. Otherwise,
the
fuel-filler
flap may open
unexpectedly and could be
damaged.
▼Refuelling
Before refuelling, close all the doors,
windows, and liftgate, and switch the
ignition OFF.
1. Using the following , unlock the
driver’s door.
xTransmitter (page 3-16)xTouch sensor (page 3-13)xDoor-lock switch (page 3-16)xAuto lock/unlock function (page
3-19)
NOTE
xWhen the driver's door is locked/
unlocked, the fuel flap is also
locked/unlocked at the same
time.
xThe time until the fuel flap is
locked after locking the driver's
door can be changed.
Refer to the Settings section in
the Mazda Connect Owner's
Manual.
xHowever, if you change the time
until the fuel flap is locked,
locking of the fuel flap using the
following functions is not
applicable.
Before Driving
Fuel and Emission
3-34