light MAZDA MODEL CX-30 2019 (in English) Workshop Manual

xPressing the unlock button on the
transmitter.
xStarting the engine with the push
button start.
x(With the advanced keyless
function)
xTouching the sensing area of the
door release touch sensor.
The hazard warning lights will flash
twice.
NOTE
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned off, the hazard
warning lights will flash twice to
indicate that the system is turned off.
▼To Stop the Alarm
A triggered alarm can be turned off
using any one of the following
methods:
xPressing the unlock button on the
transmitter.
xStarting the engine with the push
button start.
x(With the advanced keyless
function)
xTouching the sensing area of the
door release touch sensor.
xPressing the electric liftgate opener
while the key is being carried.
The hazard warning lights will
flash
twice.
Before Driving
Security System
3-52

Rocking the Vehicle
▼Rocking the Vehicle
WARNING
Do not spin the wheels at high speed,
and do not allow anyone to stand
behind a wheel when pushing the
vehicle:
When the vehicle is stuck, spinning the
wheels at high speed is dangerous. The
spinning tyre could overheat and
explode. This could cause serious
injuries.
CAUTION
Too much rocking may cause engine
overheating , transmission failure, and
tyre damage.
If you must rock the vehicle to free it
from snow, sand or mud, depress the
accelerator slightly and slowly move
the shift lever/selector lever from 1 (D)
to R position.
Winter Driving
▼Winter Driving
Carry emergency gear, including tyre
chains, window scraper,
flares, a small
shovel, jumper leads, and a small bag
of sand or salt.
Ask an expert repairer (we recommend
an Authorised Mazda Repairer) to
check the following:
xHave the proper ratio of antifreeze in
the radiator.
Refer to Engine Coolant on page
6-28.
xInspect the battery and its leads.
Cold reduces battery capacity.
xUse an engine oil appropriate for the
lowest ambient temperatures that
the vehicle will be driven in (page
6-24).
xInspect the ignition system for
damage and loose connections.
xUse washer fluid made with
antifreezeŠbut do not use engine
coolant antifreeze for washer fluid
(page 6-31).
NOTE
xRemove snow before driving. Snow
left on the windscreen is dangerous
as it could obstruct vision.
xDo not apply excessive force to a
window scraper when removing ice
or frozen snow on the mirror glass
and windscreen.
xNever use warm or hot water for
removing snow or ice from windows
and mirrors as it could result in the
glass cracking.
Before Driving
Driving Tips
3-56

xDrive slowly. Braking performance
can be adversely affected if snow or
ice adheres to the brake
components. If this situation occurs,
drive the vehicle slowly, releasing the
accelerator pedal and lightly applying
the brakes several times until the
brake performance returns to
normal.
▼Snow Tyres
WARNING
Use only the same size and type tyres
(snow, radial, or non-radial) on all 4
wheels:
Using tyres different in size or type is
dangerous. Your vehicle's handling
could be greatly affected and result in
an accident.
CAUTION
Check local regulations before using
studded tyres.
NOTE
If your vehicle is equipped with the tyre
pressure monitoring system, the system
may not function correctly when using
tyres with steel wire reinforcement in
the sidewalls (page 4-233).
Use snow tyres on all 4 wheels
Do not exceed the maximum
permissible speed for your snow tyres
or legal speed limits.
Europe
When snow tyres are used, select the
specified size and pressure (page
9-10).
▼Ty re C h a i n s
Check local regulations before using
tyre chains.
CAUTION
¾Chains may affect handling.
¾Do not go faster than 50 km/h (30
mph) or the chain manufacturer's
recommended limit, whichever is
lower.
¾Drive carefully and avoid bumps,
holes, and sharp turns.
¾Avoid locked-wheel braking.
¾Do not use chains on a temporary
spare tyre; it may result in damage to
the vehicle and to the tyre.
In some models, the vehicle is not
equipped with a factory installed
temporary spare tyre.
¾Do not use chains on roads that are
free of snow or ice. The tyres and
chains could be damaged.
¾Chains may scratch or chip
aluminium wheels.
NOTE
If your vehicle is equipped with the tyre
pressure monitoring system, the system
may not function correctly when using
tyre chains.
Install the chains on the front tyres
only.
Do not use chains on the rear tyres.
Before Driving
Driving Tips
3-57

Driving In Flooded Area
▼Driving In Flooded Area
WARNING
Dry off brakes that have become wet
by driving slowly, releasing the
accelerator pedal and lightly applying
the brakes several times until the
brake performance returns to normal:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected.
CAUTION
Do not drive the vehicle on flooded
roads as it could cause short circuiting
of electrical/electronic parts, or engine
damage or stalling from water
absorption. If the vehicle has been
immersed in water, consult an expert
repairer (we recommend an
Authorised Mazda Repairer).
Turbocharger Information
(SKYACTIV-D 1.8)
▼Turbocharger Information
(SKYACTIV-D 1.8)
CAUTION
¾After driving at freeway speeds or up
a long hill, trailer towing for a long
time, idle the engine at least 30
seconds before stopping it.
Otherwise, the turbocharger could
be damaged. However, when i-stop
operates, idling is unnecessary.
¾Racing or over-revving the engine,
particularly after it's just been
started, can damage the
turbocharger.
¾To protect the engine from damage,
the engine is designed so that it
cannot be raced just after starting it
in extremely cold weather.
The turbocharger greatly enhances
engine power. Its advanced design
provides improved operation and
requires minimum maintenance.

To get the most from it, observe the
following.
1. Change engine oil and filter
according to Scheduled
Maintenance.
Refer to Europe on page 6-3.
Refer to Except Europe on page
6-6.
2. Use only recommended engine oil
(page 6-24). Extra additives are
NOT recommended.
Before Driving
Driving Tips
3-59

▼Ty re s
When towing a trailer, make sure all
tyres are inflated to the recommended
cold-tyre pressure, as indicated on the
tyre pressure chart on the driver's door
frame. Trailer tyre size, load rating, and
inflation pressures should conform to
tyre manufacturer specifications.
WARNING
Never use the temporary spare tyre
when towing:
Using the temporary spare tyre on your
vehicle when towing a trailer is
dangerous as it could result in tyre
failure, loss of control, and injury to
vehicle occupants.
▼Safety Chains
Safety chains must be used as a
precautionary measure should the
trailer become unintentionally
unhitched. They should cross under the
trailer tongue and attach to the hitch.
Leave enough slack to allow full turns.
Consult literature published by your
trailer or hitch manufacturer for more
details.
WARNING
Make sure the safety chain is securely
attached to both the trailer and the
vehicle prior to departure:
Towing a trailer without using a safety
chain securely attached to both the
trailer and the vehicle is dangerous. If
damage occurs to the coupling unit or
hitch ball, the trailer could wander into
another lane and cause a collision.
▼Trailer Lights
CAUTION
Do not connect a trailer lighting system
directly to the lighting system of your
Mazda. This may damage your
vehicle's electrical system and lighting
systems. To connect the lighting
system, consult an expert repairer (we
recommend an Authorised Mazda
Repairer)
▼Trailer Brakes
Check the Maximum trailer
towing-load table in Weight Limits
(page 3-61), and if your trailer weight
exceeds the value in the TOTAL
TRAILER WEIGHT (Trailer without
brake), trailer brakes are required.
If your trailer has brakes, make sure
they meet regulations.
WARNING
Do not connect a hydraulic
trailer-brake system to your vehicle's
brake system:
Connecting a hydraulic trailer-brake
system directly to the vehicle brake
system is dangerous and will result in
inadequate braking and possible injury.
▼Trailer Towing Tips
Before driving
xVerify that your Mazda maintains a
near-normal attitude when a loaded
or unloaded trailer is connected. Do
not drive if it has an abnormal
front-up or front-down position.
Inspect for incorrect nose weight,
worn suspension parts, and trailer
overloading. Have the vehicle
inspected by an expert repairer (we
Before Driving
To w i n g
3-66

recommend an Authorised Mazda
Repairer).
xMake sure the trailer cargo is secure
to prevent it from shifting.
xMake sure the mirrors meet all
government regulations. Inspect
them.
xBefore starting out, inspect the
operation of all vehicle and trailer
lights and all vehicle-to-trailer
connections. Stop and re-inspect all
lights and connections after driving a
short distance.
Driving
xYour Mazda will handle differently
with a trailer in tow, so practice
turning , backing , and stopping in a
traffic-free area.
xTake time to get accustomed to the
extra weight and length.
xDo not exceed 100 km/h (62 mph)
with a trailer in tow. If the local legal
maximum speed with a trailer in tow
is less than 100 km/h (62 mph), do
not exceed the legal speed.
CAUTION
If the vehicle exceeds 100 km/h (62
mph) with a trailer in tow, the
vehicle could be damaged.
xWhen ascending a hill, shift into a
lower gear to reduce the possibility
of overloading or overheating the
engine, or both.
xWhen descending a hill, shift into a
lower gear and use engine
compression as a braking effect. Pay
constant attention to speed and use
the brakes only as needed. Holding
the brake pedal down for a
prolonged period may cause the
brakes to overheat and lose power.
Parking
Avoid parking on an incline with a
trailer. If this must be done, follow
these instructions.
Parking on an Incline
1. Set the parking brake and the
brakes.
2. Have someone block the wheels of
the vehicle and trailer while you
apply the brakes.
3. After the wheels are blocked,
release the parking brake and the
brakes slowly, allowing the blocks
to bear the load.
4. Set the parking brake firmly.
5. If the vehicle has an automatic
transmission, put the selector lever
in P position. If it has a manual
transmission, place the gear shift in
1 or R position.
Starting on an Incline
1. Start the engine (page 4-5).
2. Release the parking brake and
slowly pull away a short distance
from the wheel blocks.
3. Stop on the nearest level ground,
set the parking brake, and pick up
the wheel blocks.
Before Driving
Towing
3-67

4When Driving
Information concerning safe driving and stopping.
Start/Stop Engine..................... 4-4
Ignition Switch.......................4-4
Starting the Engine................. 4-5
Turning the Engine
Off.......... 4-10
i-stop
*................................. 4-11
Cylinder Deactivation
*..........4-20
Instrument Cluster and
Display.................................. 4-21
Instrument Cluster and
Display................................4-21
Instrument Cluster............... 4-21
Active Driving Display.......... 4-39
Manual Transmission
Operation.............................. 4-41
Manual Transmission Shift
Pattern................................ 4-41
Automatic Transmission........... 4-43
Automatic Transmission
Controls.............................. 4-43
Shift-Lock System................. 4-44
Transmission Ranges............ 4-45
Manual Shift Mode.............. 4-46
Direct Mode
*.......................4-52
Driving Tips......................... 4-53
Switches and Controls............. 4-54
Lighting Control................... 4-54
Rear Fog Light
*..................... 4-59
Turn and Lane-Change
Signals................................ 4-60
Windscreen Wipers and
Washer............................... 4-61
Rear Window Wiper and
Washer............................... 4-64
Headlight Washer
*............... 4-65
Rear Window Defogger........ 4-66
Horn................................... 4-67
Hazard Warning Flasher....... 4-68
Brake.....................................4-69
Brake System....................... 4-69
AUTOHOLD........................ 4-74
Emergency Stop Signal
System................................ 4-78
Hill Launch Assist (HLA)........4-79
ABS/TCS/DSC/Off-Road
Traction Assist.........................4-80
Antilock Brake System
(ABS).................................. 4-80
Traction Control System
(TCS).................................. 4-81
Dynamic Stability Control
(DSC)................................. 4-83
Off-Road Traction Assist
*...... 4-84
M Hybrid............................... 4-86
M Hybrid............................ 4-86
*Some models.4-1

Drive Selection....................... 4-90
Drive Selection
*................... 4-90
i-ACTIV AWD......................... 4-92
i-ACTIV AWD Operation...... 4-92
Power Steering....................... 4-93
Power Steering.....................4-93
i-ACTIVSENSE......................... 4-94
i-ACTIVSENSE...................... 4-94
Adaptive Front Lighting System
(AFS)
*................................. 4-98
High Beam Control System
(HBC)
*................................ 4-99
Adaptive LED Headlights
(ALH)
*............................... 4-101
Lane Departure Warning System
(LDWS)
*............................ 4-103
Blind Spot Monitoring (BSM)
*......
........................................ 4-106
Traffic Sign Recognition System
(TSR)
*................................4-111
Distance & Speed Alert (DSA)
*.....
........................................ 4-118
Driver Attention Alert (DAA)
*.......
........................................ 4-119
Driver Monitoring (DM)
*.... 4-121
Front Cross Traffic Alert
(FCTA)
*............................. 4-123
Rear Cross Traffic Alert (RCTA)
*....
........................................ 4-126
Mazda Radar Cruise Control
(MRCC)
*........................... 4-130
Mazda Radar Cruise Control with
Stop & Go function (MRCC with
Stop & Go function)
*......... 4-139
Cruising &
Tra ffi c Support
(CTS)
*............................... 4-148
Lane-keep Assist System (LAS)
*.....
........................................ 4-162
Adjustable Speed Limiter
(ASL)
*................................4-166
Intelligent Speed Assistance
(ISA)
*................................ 4-170
4-2*Some models.

Ignition Switch
▼Push Button Start Positions
The system operates only when the key
is within operational range.
Each time the push button start is
pressed, the ignition switches in the
order of
off, ACC, and ON. Pressing
the push button start again from ON
switches the ignition
off.
1. Indicator light
2. Push button start
NOTE
xThe engine starts by pressing the
push button start while depressing
the clutch pedal (manual
transmission) or the brake pedal
(automatic transmission). To switch
the ignition position, press the push
button start without depressing the
pedal.
xDo not leave the ignition switched
ON while the engine is not running.
Doing so could result in the battery
going dead. If the ignition is left in
ACC (For automatic transmission,
the selector lever is in the P position,
and the ignition is in ACC), the
ignition switches off automatically
after about 25 minutes.
Off
The power supply to electrical devices
turns off and the indicator light
(amber) also turns off.
In this position the steering wheel is
locked.
WARNING
Before leaving the driver's seat,
always switch the ignition off, set the
parking brake, and make sure the
selector lever is in P (automatic
transmission) position or in 1st gear
or R (manual transmission):
Leaving the driver's seat without
switching the ignition off, setting the
parking brake, and shifting the selector
lever to P (automatic transmission)
position or to 1st gear or R (manual
transmission) is dangerous.
Unexpected vehicle movement could
occur which could result in an
accident.
In addition, if your intention is to leave
the vehicle for even a short period, it is
important to switch the ignition
off, as
leaving it in another position will
disable some of the vehicle's security
systems and run the battery down.
NOTE
(Locked steering wheel)
If the push button start indicator light
(green) is
flashing , a message is
displayed on the multi-information,
and the beep sound is heard, this
indicates that the steering wheel is not
unlocked. To unlock the steering
wheel, press the push button start
while moving the steering wheel left
and right.
When Driving
Start/Stop Engine
4-4

ACC (Accessory)
Some electrical accessories will
operate and the indicator light (amber)
illuminates.
In this position the steering wheel is
unlocked.
NOTE
The keyless entry system does not
function while the push button start
has been pressed to ACC, and the
doors will not lock/unlock even if they
have been locked manually.
ON
This is the normal running position
after the engine is started. The
indicator light (amber) turns off. (The
indicator light (amber) illuminates
when the ignition is switched ON and
the engine is not running.)
Some indicator lights/warning lights
should be inspected before the engine
is started.
Refer to Warning/Indicator Lights on
page 4-32.
Refer to Indication/Indicator Lights on
page 4-34.
NOTE
(SKYACTIV-G 2.0, SKYACTIV-G 2.5,
SKYACTIV-X 2.0)
When the push button start is pressed
to ON, the sound of the fuel pump
motor operating near the fuel tank can
be heard. This does not indicate an
abnormality.
Starting the Engine
▼Starting the Engine
WARNING
Radio waves from the key may affect
medical devices such as pacemakers:
Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will affect
the device.
NOTE
xThe key must be carried because the
key carries an immobilizer chip that
must communicate with the engine
controls at short range.
xThe engine can be started when the
push button start is pressed from off,
ACC, or ON.
xThe push button start system
functions (function which can start
the engine by only carrying the key)
can be deactivated to prevent any
possible adverse effect on a user
wearing a pacemaker or other
medical device. If the system is
deactivated, you will be unable to
start the engine by carrying the key.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) for details. If the push
button start system functions have
been deactivated, you can start the
engine by following the procedure
indicated when the key battery goes
dead.
Refer to Engine Start Function When
Key Battery is Dead on page 4-8.
xAfter starting a cold engine, the
engine speed increases and a
whining sound from the engine
compartment can be heard.
When Driving
Start/Stop Engine
4-5