light MAZDA MODEL CX-30 2019 (in English) Service Manual

Mirrors
▼Mirrors
Before driving , adjust the inside and
outside mirrors.
▼Outside Mirrors
WARNING
Be sure to look over your shoulder
before changing lanes:
Changing lanes without taking into
account the actual distance of the
vehicle in the convex mirror is
dangerous. You could have a serious
accident. What you see in the convex
mirror is closer than it appears.
NOTE
(Driver's Side Wide Angle Mirror*)
xThe wide angle mirror has 2
curvatures on its surface separated by
a region line into outer and inner
regions. The inner region is a
standard convex mirror whereas the
outer region allows for a wider range
of visibility within the same sweep.
This combination allows for better
assurance when making lane
changes.

1. Region line

xThe perceived distance of objects in
the outer and inner regions of the
wide angle mirror is different.
Objects appearing in the outer
region are actually further away than
they are in the inner region.
Power mirror adjustment
The ignition must be switched to ACC
or ON position.

To adjust:
1. Press the select switch for the
outside mirror to be adjusted to
turn on the indicator light.
2. Press the adjustment switch to
adjust the angle of the outside
mirror.
1. Indicator light
2. Select switch
3. Adjustment switch

After adjusting the angle of the outside
mirror, press the select switch for the
outside mirror to be adjusted to turn
off the indicator light.
Before Driving
Mirrors
3-36*Some models.

NOTE
(With driving position memory
function)
The on-road outside mirror position
can be programmed in conjunction
with the driving position memory
function.
Refer to Driving Position Memory on
page 2-10.
Power mirrors with reverse tilt down
function*
The outside mirrors tilt downward to
facilitate the view of the lower area on
each side of the vehicle.
1. Switch the ignition ON.
2. Press the select switch for the
outside mirror to be tilted
downward to turn on the indicator
light of the select switch.
3. Shift the shift lever/selector lever to
the R position to tilt the outer
mirror on the side where the select
button was pressed downward.
NOTE
When any of the following condition is
met, the outer mirrors return to their
normal positions.
xThe ignition is switched to a position
other than ON.
xThe shift lever/selector lever is
shifted to a position other than R.
xThe select switch is pressed again.
Folding outside mirror
WARNING
Always return the outside mirrors to
the driving position before you start
driving:
Driving with the outside mirrors folded
in is dangerous. Your rear view will be
restricted, and you could have an
accident.
Manual folding outside mirror
Fold the outside mirror rearward until
it is flush with the vehicle.

Power folding outside mirror
WARNING
Do not touch a power folding outside
mirror while it is moving:
Touching the power folding outside
mirror when it is moving is dangerous.
Your hand could be pinched and
injured or the mirror could be
damaged.
Use the switch to set the mirror to the
on-road position:
Setting the power folding outside
mirror to the on-road position by hand
is dangerous. The mirror will not lock
in position and will prevent effective
rearview visibility.
Before Driving
Mirrors
*Some models.3-37

▼Rearview Mirror
WARNING
Do not stack cargo or objects higher
than the seatbacks:
Cargo stacked higher than the
seatbacks is dangerous. It can block
your view in the rearview mirror, which
might cause you to hit another car
when changing lanes.
Rearview mirror adjustment
Before driving, adjust the rearview
mirror to centre on the scene through
the rear window.

NOTE
For the manual antidazzle mirror,
perform the adjustment with the
antidazzle lever in the day position.
Reducing glare from headlights
Manual antidazzle mirror
Push the antidazzle lever forward for
day driving. Pull it back to reduce glare
of headlights from vehicles at the rear.

1. Antidazzle lever
2. Night
3. Day

Auto-dimming mirror
The auto-dimming mirror
automatically reduces the glare of
headlights from vehicles at the rear
when the ignition is switched ON.

NOTE
xDo not use glass cleaner or suspend
objects on or around the light
sensor. Otherwise, light sensor
sensitivity will be affected and may
not operate normally.
Before Driving
Mirrors
3-39

1. Light sensor

xThe auto-dimming function is
cancelled when the ignition is
switched ON and the shift lever/
selector lever is in the R position.
Before Driving
Mirrors
3-40

Powe r Wi n d ow s
▼Power Windows
The windows can be opened/closed
by operating the power window
switches.
WARNING
Make sure the opening is clear before
closing a window:
Closing a power window is dangerous.
A person's hands, head, or even neck
could be caught by the window and
result in serious injury or even death.
This warning applies especially to
children.
Never allow children to play with
power window switches:
Power window switches that are not
locked with the power window lock
switch would allow children to operate
power windows unintentionally, which
could result in serious injury if a child's
hands, head or neck becomes caught
by the window.
Make sure nothing blocks the window
just before it reaches the fully closed
position or while fully holding up the
power window switch:
Blocking the power window just before
it reaches the fully closed position or
while fully holding up the power
window switch is dangerous.
In this case, the jam-safe function may
not prevent the window from closing
all the way. If
fingers are caught,
serious injuries could occur.
Do not let a child put a hand or head
out of the window while driving the
vehicle:
If the person's hand or head hits
something outside the vehicle, or
sudden braking is applied, it could
result in serious injury or death.
NOTE
When driving with only 1 of the rear
windows open, your ears might
experience a resonating sound.
However, this does not indicate a
problem. The sound can be reduced
by slightly opening a front window or
by changing the size of the rear
window opening.
▼Opening/Closing Windows
The window opens while the switch is
pressed and it closes while the switch
is pulled up with the ignition switched
ON. Do not open or close 3 or more
windows at the same time.
The front passenger's window and rear
windows can be opened/closed when
the power window lock switch on the
driver's door is in the unlocked
position. Keep this switch in the locked
Before Driving
Windows
3-41

Modification and
Add-On Equipment
▼Modification and Add-On
Equipment
Mazda cannot guarantee the
immobilizer and the theft-deterrent
systems' operation if the system has
been modified or if any add-on
equipment has been installed.
CAUTION
To avoid damage to the vehicle, do not
modify the system or install any add-on
equipment to the immobilizer and the
theft-deterrent systems or the vehicle.
Immobilizer System
▼Immobilizer System
The immobilizer system allows the
engine to start only with a key the
system recognises.

If someone attempts to start the
engine with an unrecognised key, the
engine will not start, thereby helping to
prevent vehicle theft.
If you have a problem with the
immobilizer system or the key, consult
an expert repairer (we recommend an
Authorised Mazda Repairer).
CAUTION
¾Changes or modifications not
expressly approved by the party
responsible for compliance could
void the user's authority to operate
the equipment.
¾To avoid damage to the key, do not:
¾Drop the key.
¾Get the key wet.
¾Expose the key to any kind of
magnetic field.
¾Expose the key to high
temperatures on places such as the
instrument panel or bonnet, under
direct sunlight.
¾If the engine does not start with the
correct key, and the security indicator
light keeps illuminating or flashing,
the system may have a malfunction.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer).
Before Driving
Security System
3-47

NOTE
xThe keys carry a unique electronic
code. For this reason, and to assure
your safety, obtaining a replacement
key requires some waiting time. They
are only available through an
Authorised Mazda Repairer.
xAlways keep a spare key in case one
is lost. If a key is lost, consult an
Authorised Mazda Repairer as soon
as possible.
xIf you lose a key, an Authorised
Mazda Repairer will reset the
electronic codes of your remaining
keys and immobilizer system. Bring
all the remaining keys to an
Authorised Mazda Repairer to reset.
Starting the vehicle with a key that
has not been reset is not possible.
▼Operation
NOTE
xThe engine may not start and security
indicator light may illuminate or flash
if the key is placed in an area where
it is difficult for the system to detect
the signal, such as on the instrument
panel or in the glove compartment.
Move the key to a location within
the signal range, switch the ignition
off, and then restart the engine.
xSignals from a TV or radio station, or
from a transceiver or mobile
telephone could interfere with your
immobilizer system. If you are using
the proper key and the engine fails to
start, check the security indicator
light.
Arming
The system is armed when the ignition
is switched from ON to off.
The security indicator light in the
instrument cluster flashes every 2
seconds until the system is disarmed.

Disarming
The system is disarmed when the
ignition is switched ON with the
correct programmed key. The security
indicator light illuminates for about 3
seconds and then turns
off.
If the engine does not start with the
correct key, and the security indicator
light remains illuminated or flashing ,
try the following:
Make sure the key is within the
operational range for signal
transmission. Switch the ignition
off,
and then restart the engine. If the
engine does not start after 3 or more
tries, contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
Before Driving
Security System
3-48

Theft-Deterrent System*
▼Theft-Deterrent System
If the theft-deterrent system detects an
inappropriate entry into the vehicle or
the intrusion sensor detects movement
in the vehicle which could result in the
vehicle (with the intrusion sensor) or
its contents being stolen, the alarm
alerts the surrounding area of an
abnormality by sounding the siren/
horn and flashing the hazard warning
lights.

The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Intrusion sensor
*
The intrusion sensor uses ultrasonic
waves to detect movement inside the
vehicle and to raise an alert of an
intrusion into the vehicle.

The intrusion sensor detects certain
kinds of movement inside the vehicle,
however, it may also respond to
phenomenon outside the vehicle such
as vibrations, loud noise, wind, and air
currents.
CAUTION
In order for the intrusion sensor to
operate appropriately, be aware of the
following:
¾Do not hang clothing or objects from
a head restraint or a coat hook.
¾Return the extension sunvisors to
their original positions.
¾Do not blind the intrusion sensor by
covering it or placing objects over it.
¾Do not allow the intrusion sensor to
get soiled or wipe it with a liquid.
¾Do not shock or cause an impact to
the intrusion sensor or the intrusion
sensor bezel.
¾Do not install seats that are not
Mazda genuine products.
¾To prevent obstruction of intrusion
sensor, do not place objects or cargo
near the intrusion sensor that are
higher than the head restraints.

1. Intrusion sensor and intrusion
sensor bezel
▼Operation
Siren/Horn triggering conditions
The siren/horn sounds intermittently
and the hazard warning lights flash for
about 30 seconds when the system is
triggered by any one of the following:
With the intrusion sensor
xUnlocking a door with the auxiliary
key, door lock switch, or an inside
door-lock knob.
xForcing open a door, the bonnet or
the liftgate.
xOpening the bonnet by operating
the bonnet release handle.
xSwitching the ignition ON without
using the push button start.
xThe intrusion sensor detects a
movement in the vehicle.
Before Driving
Security System
*Some models.3-49

The system will be triggered again (up
to 10 times) if one of the above
conditions remains.

xDisconnecting the battery terminal
(the hazard warning lights do not
flash).
The system will be triggered about 10
times.
Without the intrusion sensor
xUnlocking a door with the auxiliary
key, door lock switch, or an inside
door-lock knob.
xForcing open a door, the bonnet or
the liftgate.
xOpening the bonnet by operating
the bonnet release handle.
xSwitching the ignition ON without
using the push button start.
If the system is triggered again, the
lights and horn will activate until the
driver's door or the liftgate is unlocked
with the transmitter.
NOTE
xThe liftgate does not open while the
theft-deterrent system is operating.
xIf the battery goes dead while the
theft-deterrent system is armed, the
siren/horn will activate and the
hazard warning lights will flash when
the battery is charged or replaced.
▼How to Arm the System
1. Close the windows and the
sunroof* securely.
NOTE
(With the intrusion sensor)
Even with a window or the sunroof*
open, the system can be armed,
however, leaving the windows or
the sunroof
* even partially open can
invite theft, and wind blowing into
the vehicle could trigger the alarm.
The intrusion sensor function can
also be cancelled.
Refer to Cancelling the Intrusion
Sensor (With Intrusion Sensor) on
page 3-51.
2. Switch the ignition OFF.
3. Make sure the bonnet, the doors,
and the liftgate are closed.
4. Press the lock button on the
transmitter.
The hazard warning lights will flash
once.
The following method will also arm
the theft-deterrent system:
Press the door-lock switch “
”
while any door is open and then
close all of the doors.
(With the advanced keyless
function)
Touch the sensing area of the door
lock touch sensor.

The security indicator light in the
instrument cluster flashes twice per
second for 20 seconds.

5. After 20 seconds, the system is fully
armed.
Before Driving
Security System
3-50*Some models.

NOTE
xThe theft-deterrent system can
also be armed by activating the
auto relock function with all the
doors, the liftgate and the bonnet
closed.
Refer to Transmitter on page 3-5.
xThe system will disarm if one of
the following operations takes
place within 20 seconds after
pressing the lock button:
xUnlocking any door.xOpening any door.xOpening the bonnet.xSwitching the ignition ON.
To rearm the system, do the
arming procedure again.
xWhen the doors are locked by
pressing the lock button on the
transmitter while the
theft-deterrent system is armed,
the hazard warning lights will
flash once to indicate that the
system is armed.
▼Cancelling the Intrusion Sensor
(With the Intrusion Sensor)
If the theft deterrent system has been
armed while any of the following
conditions are present, cancel the
intrusion sensor to prevent the alarm
from triggering unnecessarily.
xLeaving the vehicle with a movable
object, passengers or pets remaining
inside.
xLeaving an object inside the vehicle
that can roll around, such as when
the vehicle is placed on a tilting,
unstable surface when being
shipped.
xHanging small objects/accessories in
the vehicle, hanging clothing on a
coat hook, or placing other items
which can move easily inside the
vehicle.
xParking in an area where there is
strong vibration or loud noise.
xWhen using a high pressure or
automatic car wash.
xContinuous shock and vibration from
hail or thunder and lightning is
transmitted to the vehicle.
xDoors are locked with a window or
the sunroof* left open.xAn accessory heater or device that
produces moving air and vibration
operates while the theft deterrent
system is armed.
NOTE
If any door or the liftgate remains
closed for 30 seconds, all the doors
and the liftgate automatically re-lock
and the theft deterrent system arms
even if a window and the sunroof
* is
left open.

To cancel the intrusion sensor, press
the intrusion sensor cancel button on
the transmitter within 20 seconds after
pressing the lock button.
The hazard warning lights will flash 3
times.
NOTE
xTo reactivate the intrusion sensor,
turn off the armed theft-deterrent
system and then rearm it.
xThe intrusion sensor is operational
when the theft-deterrent system is
armed. To cancel the intrusion
sensor, press the intrusion sensor
cancel button each time the
theft-deterrent system is armed.
▼To Turn Off an Armed System
An armed system can be turned off
using any one of the following
methods:
Before Driving
Security System
*Some models.3-51