engine MAZDA MODEL CX-30 2019 (in English) Workshop Manual

▼Odometer, Trip Meter and Trip
Meter Selector
You can switch between the odometer
and trip meter display using the TRIP
switch.

1. TRIP switch
2. Odometer display
3. Trip meter A display
4. Trip meter B display
Odometer
The odometer records the total
distance the vehicle has been driven.
Tr i p m e t e r
The driving distance for a specified
interval is indicated. Two types (TRIP A,
TRIP B) of interval distance and the
average fuel economy for each can be
measured.

For instance, trip meter A can record
the distance from the point of origin,
and trip meter B can record the
distance from where the fuel tank is
filled.

When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed.

The trip meter and average fuel
economy can be reset by pressing the
TRIP switch for 1.5 seconds or more
while in each mode.
NOTE
xOnly the trip meters record tenths of
kilometres (miles).
xThe trip record will be erased when:
xThe power supply is interrupted
(blown fuse or the battery is
disconnected).
xThe vehicle is driven over 9999.9
km (mile).
▼Engine Coolant Temperature
Gauge
Displays the engine coolant
temperature. The blue range of the
gauge indicates that the engine coolant
temperature is low, and the red range
of the gauge indicates that the engine
coolant temperature is high and
overheating.

When Driving
Instrument Cluster and Display
4-25

CAUTION
When the engine coolant temperature
gauge needle is in the red range, the
engine coolant temperature is
extremely high. Drive slowly to reduce
engine load. If the engine coolant
temperature gauge needle is in the red
range, there is the possibility of
overheating. Park the vehicle in a safe
place immediately and take
appropriate measures.
Refer to Overheating on page 7-44.
NOTE
xIf the engine or engine coolant
temperature is high or low, the
engine output may be restricted to
protect the engine.
xDuring normal driving , the engine
coolant temperature stabilizes at 100
°C (210 °F) or less, and the gauge
indicates a range lower than 100 °C
(210 °F).
▼Fuel Gauge
The fuel gauge shows approximately
how much fuel is remaining in the tank
when the ignition is switched ON. We
recommend keeping the tank over 1/4
full.

1. Full
2. 1/4 Full
3. Empty

If the low fuel warning light illuminates
or the fuel level is very low, refuel as
soon as possible.
If inconsistency in engine performance
or stalling occurs due to low fuel level
conditions, refuel the vehicle as soon
as possible and add at least 10 L (2.7
US gal, 2.2 Imp gal) of fuel.
Refer to Low Fuel Warning Indication/
Warning Light on page 7-58.
NOTE
xAfter refuelling, it may require some
time for the indicator to stabilize. In
addition, the indicator may deviate
while driving on a slope or curve
since the fuel moves in the tank.
When Driving
Instrument Cluster and Display
4-26

▼Outside Temperature Display
When the ignition is switched ON, the
outside temperature is displayed.

NOTE
xUnder the following conditions, the
outside temperature display may
differ from the actual outside
temperature depending on the
surroundings and vehicle conditions:
xSignificantly cold or hot
temperatures.
xSudden changes in outside
temperature.
xThe vehicle is parked.xThe vehicle is driven at low speeds.
Changing the Temperature Unit of the
Outside Temperature Display
The outside temperature unit can be
switched between Celsius and
Fahrenheit.
Settings can be changed by operating
the centre display screen.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
NOTE
When the temperature unit indicated
in the outside temperature display is
changed, the temperature unit
indicated in the engine coolant gauge
display changes in conjunction with it.
Outside Temperature Warning*
When the outside temperature is low,
the indication flashes and a beep
sound is heard to warn the driver of
the possibility of icy roads.
If the outside temperature is lower
than about 4 °C (39 °F), the outside
temperature display and the
mark
flashes for about 3 seconds and a beep
sound is heard once.
NOTE
If the outside temperature is lower
than -20 °C (-4 °F), the beep sound
does not operate. However, the
mark illuminates.
▼Distance-to-empty
This displays the approximate distance
you can travel on the remaining fuel
based on the fuel economy.
The distance-to-empty will be
calculated and displayed every second.

NOTE
xEven though the distance-to-empty
display may indicate a
sufficient
amount of remaining driving distance
before refuelling is required, refuel as
soon as possible if the fuel level is
very low or the low fuel warning light
illuminates.
xThe display will not change unless
you add more than approximately 9
L (2.3 US gal, 1.9 Imp gal) of fuel.
When Driving
Instrument Cluster and Display
4-28*Some models.

▼Warning Indication/Warning Lights
These lights turn on or flash to notify the user of the system operation status or a
system malfunction.
Signal Warning Refer to
(Red)Brake System Warning Indication/Warning Light
*17-49
ABS Warning Indication/Warning Light*1
Electronic
Brake Force
Distribution
System Warn-
ing
7-50
ABS warning
7-52
Charging System Warning Indication/Warning Light*17-50
Engine Oil Warning Indication/Warning Light*17-50
High Engine Coolant Temperature Warning Indication 7-51
Power Steering Malfunction Indication/Indicator Light*17-51
Master Warning Indication 7-52
(Amber)Brake Control System Warning Indication/Warning Light
*17-52
Brake Override Warning Indication 7-53
Check Engine Indication/Light*17-53
Petrol Particulate Filter Warning Indication/Warning Light*1(SKYAC-
TIV-X 2.0)7-54
Diesel Particulate Filter Warning Indication/Warning Light
*1(SKYAC-
TIV-D 1.8)7-54
When Driving
Instrument Cluster and Display
4-32

Signal Warning Refer to
(Amber)
*i-stop Warning Indication/Warning Light*17-53
*Automatic Transmission Warning Indication/Warning Light*17-55
*AWD Warning Indication/Warning Light*17-56
Air Bag/Seat Belt Pretensioner System Warning Indication/Warning
Light*17-55
*Tyre Pressure Monitoring System (TPMS) Warning Indication/Warn-
ing Light*1
Flashing
7-57
Tu r n s o n
7-60
(Red)KEY Warning Indication/Warning Light
*17-56
(Amber)
*High Beam Control System (HBC) Warning Indication/Warning
Light*17-58
*Adaptive LED Headlights (ALH) Warning Indication/Warning Light*17-58
i-ACTIVSENSE Warning Indication/Warning Light*17-58
Exterior Light Warning Indication/Warning Light*17-58
Low Fuel Warning Indication/Warning Light 7-58
Engine Oil Level Warning Indication/Warning Light*17-59
*120 km/h Warning Light*17-57
Seat Belt Warning Indication/Warning Light (Front seat) 7-59
(Red)Seat Belt Warning Light (Rear seat) 7-59
When Driving
Instrument Cluster and Display
*Some models.4-33

Signal Warning Refer to
*Low Washer Fluid Level Warning Indication/Warning Light7-60
Door-Ajar Warning Indication 7-60
Liftgate-Ajar Warning Indication 7-60
Door-Ajar Warning Light 7-60
*1 The light turns on when the ignition is switched on for an operation check, and turns off a few
seconds later or when the engine is started. If the light does not turn on or remains turned on, have
the vehicle inspected at an expert repairer (we recommend an Authorised Mazda Repairer).
▼Indication/Indicator Lights
These lights turn on or flash to notify the user of the system operation status or a
system malfunction.
Signal Indicator Refer to
(Green)Seat Belt Indicator Light (Rear seat) 2-24
*Front Passenger Air Bag Deactivation Indicator Light2-51
Security Indicator LightImmobilizer
System
3-48
Theft-Deterrent
System
3-50
Malfunction
7-56
(Green)KEY Indicator Light 4-5
(Green)
*i-stop Indicator Light4-18
When Driving
Instrument Cluster and Display
4-34*Some models.

Signal Indicator Refer to
(Green)
*Mazda Radar Cruise Control (MRCC) Set Indication4-134
*Mazda Radar Cruise Control with Stop & Go function (MRCC with
Stop & Go function) Set Indication4-143
*Cruising &
Tra ffi c Support (CTS) Set Indication4-154
*Smart Brake Support (SBS) OFF Indicator Light*1
Smart Brake
Support (SBS)
4-177
Smart Brake
Support [Rear]
(SBS-R)
4-180
Smart Brake
Support [Rear
Crossing]
(SBS-RC)
4-184
(White)
*Intelligent Speed Assistance (ISA) Standby Indication4-171
*Adjustable Speed Limiter (ASL) Standby Indication4-167
(Green)
*Intelligent Speed Assistance (ISA) Set Indication4-171
*Adjustable Speed Limiter (ASL) Set Indication4-167
(White)
*Cruise Standby Indication4-228
(Green)
*Cruise Set Indication4-228
*1 The light turns on when the ignition is switched on for an operation check, and
turns off a few seconds later or when the engine is started. If the light does not
turn on or remains turned on, have the vehicle inspected at an expert repairer
(we recommend an Authorised Mazda Repairer).
*2 The light turns on continuously when the parking brake is applied.
▼Wrench Indication/Indicator LightThe wrench indication/indicator light
is displayed/turns on under the
following conditions.
xWhen the preset maintenance
period has arrived.
When Driving
Instrument Cluster and Display
*Some models.4-37

Refer to the Information section in
the Mazda Connect Owner's
Manual.
CAUTION
¾When the maintenance period
arrives, have your vehicle inspected
by an expert repairer (we
recommend an Authorised Mazda
Repairer) as soon as possible. If
maintenance is neglected, a
decrease in vehicle performance
may occur which could cause
damage. Have your vehicle
inspected before the maintenance
period arrives.
¾If the vehicle continues to be
driven after the engine oil
replacement period has passed, it
could cause damage to the engine.
Replace the engine oil before the
maintenance period arrives.
¾(SKYACTIV-D 1.8)
Depending on the vehicle use
conditions, engine oil replacement
is required due to engine oil
deterioration from fuel penetrating
the engine oil. If “Excessive Oil
Level. Have the Vehicle Inspected”
is displayed on the
multi-information display in the
instrument cluster, have your
vehicle inspected at an expert
repairer (we recommend an
Authorised Mazda Repairer).
x(SKYACTIV-D 1.8)
xWhen fuel filter (sedimentor)
draining is required. Consult an
expert repairer (we recommend an
Authorised Mazda Repairer).
NOTE
xThe wrench indication/indicator
light may display/turn on earlier than
the preset period depending on
vehicle usage conditions.
xWhenever the engine oil is replaced,
a reset of the vehicle engine control
unit is necessary.
Refer to the Information section in
the Mazda Connect Owner's
Manual.

▼Glow Indicator Light (SKYACTIV-D
1.8)
When the ignition is switched ON, the
glow indicator light turns on. The glow
indicator light turns
off when
preheating is finished.

A problem in the system might be
indicated under the following
conditions. Have your vehicle
inspected by an expert repairer (we
recommend an Authorised Mazda
Repairer).
xThe glow indicator light does not
turn on when the ignition is switched
ON or it remains on.
xThe glow indicator light is flashing.
NOTE
If the vehicle is left with the ignition
switched ON without starting the
engine and a long period of time has
elapsed since preheating
finished, the
preheating may be performed again
and the glow indicator light may turn
on.
When Driving
Instrument Cluster and Display
4-38

Manual Transmission
Shift Pattern
▼Manual Transmission Shift Pattern
1. Neutral position

The shift pattern of the transmission is
conventional, as shown.

Depress the clutch pedal all the way
down while shifting; then release it
slowly.

Your vehicle is equipped with a device
to prevent shifting to R (reverse) by
mistake. Push the shift lever downward
and shift to R.

WARNING
Do not use sudden engine braking on
slippery road surfaces or at high
speeds:
Shifting down while driving on wet,
snowy, or frozen roads, or while
driving at high speeds causes sudden
engine braking , which is dangerous.
The sudden change in tyre speed could
cause the tyres to skid. This could lead
to loss of vehicle control and an
accident.
Always leave the shift lever in 1 or R
position and set the parking brake
when leaving the vehicle unattended:
Otherwise the vehicle could move and
cause an accident.
CAUTION
¾Keep your foot off the clutch pedal
except when shifting gears. Also, do
not use the clutch to hold the vehicle
on an upgrade. Riding the clutch will
cause needless clutch wear and
damage.
¾Do not apply any excessive lateral
force to the shift lever when
changing from 5th to 4th gear. This
could lead to the accidental
selection of 2nd gear, which could
result in damage to the transmission.
¾Make sure the vehicle comes to a
complete stop before shifting to R.
Shifting to R while the vehicle is still
moving may damage the
transmission.
NOTE
xIf shifting to R is difficult, shift back
into neutral, release the clutch pedal,
and try again.
x(With M Hybrid)
When Driving
Manual Transmission Operation
4-41

The parking brake may be applied
automatically to prevent the vehicle
from moving if the engine stalls while
the vehicle is on a slope.
x(With i-stop function)
If the engine has stopped due to
stalling, it can be restarted by
depressing the clutch pedal within 3
seconds of the engine stopping.
The engine cannot be restarted even
if the clutch pedal is depressed
under the following conditions:
xThe driver's door is open.xThe driver's seat belt is unfastened.xThe clutch pedal is not released
completely after the engine stalled.
xThe clutch pedal is depressed with
the engine not stopped
completely.
▼Gear Shift Indicator (GSI)
The GSI supports you to obtain
optimum fuel economy and smooth
driving. It displays the selected gear
position in the instrument cluster as
well as
notifies the driver to change to
the most suitable gear position
corresponding to the actual driving
condition.

1. Selected gear position
2. Suitable gear position
Indication Condition
NumeralThe selected gear position is
displayed.
Indication Condition
and numer-
alShift up or down to the indi-
cated gear position is recom-
mended.
CAUTION
Do not rely solely on the shift-up/
shift-down recommendations by
indications. The actual driving situation
might require shift operations different
from indication. To avoid the risk of
accidents, the road and traffic
conditions have to be judged correctly
by the driver before shifting.
NOTE
The GSI turns off when the following
operations are performed.
xThe vehicle is stopped.xThe vehicle is put in neutral.xThe vehicle is driven in reverse.xThe clutch is not fully engaged when
accelerating from a stop.
xThe clutch pedal remains depressed
for 2 seconds or longer while driving.
When Driving
Manual Transmission Operation
4-42