oil change MAZDA MODEL CX-30 2019 Owners Manual (in English)

Driving In Flooded Area
▼Driving In Flooded Area
WARNING
Dry off brakes that have become wet
by driving slowly, releasing the
accelerator pedal and lightly applying
the brakes several times until the
brake performance returns to normal:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected.
CAUTION
Do not drive the vehicle on flooded
roads as it could cause short circuiting
of electrical/electronic parts, or engine
damage or stalling from water
absorption. If the vehicle has been
immersed in water, consult an expert
repairer (we recommend an
Authorised Mazda Repairer).
Turbocharger Information
(SKYACTIV-D 1.8)
▼Turbocharger Information
(SKYACTIV-D 1.8)
CAUTION
¾After driving at freeway speeds or up
a long hill, trailer towing for a long
time, idle the engine at least 30
seconds before stopping it.
Otherwise, the turbocharger could
be damaged. However, when i-stop
operates, idling is unnecessary.
¾Racing or over-revving the engine,
particularly after it's just been
started, can damage the
turbocharger.
¾To protect the engine from damage,
the engine is designed so that it
cannot be raced just after starting it
in extremely cold weather.
The turbocharger greatly enhances
engine power. Its advanced design
provides improved operation and
requires minimum maintenance.

To get the most from it, observe the
following.
1. Change engine oil and filter
according to Scheduled
Maintenance.
Refer to Europe on page 6-3.
Refer to Except Europe on page
6-6.
2. Use only recommended engine oil
(page 6-24). Extra additives are
NOT recommended.
Before Driving
Driving Tips
3-59

▼Indicators
1. Manual shift mode indication
2. Gear position indication
Manual shift mode indication
In manual shift mode, the “M” of the
shift position indication in the
instrument panel illuminates.
Gear position indication
The numeral for the selected gear
illuminates.

NOTE
xIf the gears cannot be shifted down
when driving at higher speeds, the
gear position indication will
flash
twice to signal that the gears cannot
be shifted down (to protect the
transmission).
xIf the automatic transmission fluid
(ATF) temperature becomes too
high, there is the possibility that the
transmission will switch to automatic
shift mode, cancelling manual shift
mode and turning off the gear
position indication illumination. This
is a normal function to protect the
AT. After the ATF temperature has
decreased, the gear position
indication illumination turns back on
and driving in manual shift mode is
restored.
x(SKYACTIV-D 1.8 (European
model))
If the engine oil temperature
becomes too high, there is the
possibility that the transmission will
switch to automatic shift mode,
cancelling manual shift mode and
turning off the gear position
indicator illumination. After the
engine oil temperature has
decreased, the gear position
indicator illumination turns back on
and driving in manual shift mode is
restored.
▼Gear Shift Indicator (GSI)*
The GSI supports you to obtain
optimum fuel economy and smooth
driving. It displays the selected gear
position in the instrument cluster as
well as notifies the driver to change to
the most suitable gear position
corresponding to the actual driving
condition.

1. Selected gear position
2. Suitable gear position
Indication Condition
NumeralThe selected gear position is
displayed.
and numer-
alShift up or down to the indi-
cated gear position is recom-
mended.
When Driving
Automatic Transmission
*Some models.4-47

¾The vehicle is driven on roads with
lane lines other than white (yellow)
lines, such as an expressway.

Do not get out of the vehicle while
the stop hold control is operating.
(Automatic transmission vehicle)
Getting out of the vehicle while the
stop hold control is operating is
dangerous as the vehicle may move
unexpectedly and result in an accident.
Before getting out of the vehicle,
switch the CTS off, apply the parking
brake, and then shift the selector lever
to the P position.

CAUTION
Turn the system off when the vehicle is
running on a chassis roller.
Heed the following cautions so that
the CTS can operate normally.
¾Turn the system off when the vehicle
is running on a chassis roller.
¾Do not modify the vehicle's
suspensions.
¾Always use wheels of the specified
size for the front and rear wheels.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) for tyre replacement.

NOTE
xThe headway control does not detect
the following as physical objects.
xVehicles approaching in the
opposite direction
xPedestriansxStationary objects (stopped
vehicles, obstructions)
xIf a vehicle ahead is travelling at an
extremely low speed, the system may
not detect it correctly.
xIf there is a structure on the road or
an object (such as a monorail) at a
low height off the ground in front of
the vehicle, the system may operate.
Therefore, do not use the CTS.
xDo not use the CTS under conditions
in which close proximity warnings
are frequently activated.
xIf it is necessary to accelerate for a
lane change or the vehicle ahead
brakes suddenly causing you to close
in on the vehicle rapidly, accelerate
using the accelerator pedal or
decelerate using the brake pedal
depending on the conditions.
xWhile the CTS is in use, any intended
engine braking does not occur even
if you shift the shift lever (manual
transmission) or the selector lever
(automatic transmission). If
deceleration is required, lower the
vehicle speed setting or depress the
brake pedal.
xWhile braking by the CTS control is
operating , you might hear an
operation sound, however, this does
not indicate a problem.
xThe brake lights turn on while
braking by the CTS control is
operating, however, they may not
turn on while the vehicle is on a
down slope at the set vehicle speed
or travelling at a constant speed and
following a vehicle ahead.
xUnder the following conditions, the
CTS may not be able to detect white
(yellow) lines or vehicles ahead
correctly and the CTS may not
operate normally.
xThe forward sensing camera (FSC)
cannot recognise the area in front
of the vehicle due to soiling or fog.
When Driving
i-ACTIVSENSE
4-150

xThe white (yellow) lane lines are
less visible because of dirt or paint
flaking.
xWhite (yellow) lane lines or
vehicles ahead are less visible
because of bad weather (rain, fog,
or snow).
xThe vehicle is driven on a
temporary lane or section with a
closed lane resulting from
construction where there might be
multiple white (yellow) lane lines,
or they are interrupted.
xThe camera picks up an obscure
line, such as a temporary line being
used for construction, or because
of shade, unmelted snow, or
grooves filled with water.
xThe road surface is wet and shiny
after rain, or there are puddles on
the road.
xHeavy luggage is loaded in the
luggage compartment or on the
rear seat causing the vehicle to tilt.
xA vehicle in front of your vehicle is
running near a white (yellow) lane
line making it less visible.
xThe windscreen is dirty or foggy.xThe vehicle is driven through an
intersection, a junction, or a fork in
the road.
xWhile white (yellow) lane lines
cannot be detected due to road or
weather conditions.
xThe surrounding brightness
suddenly changes such as when
entering or exiting a tunnel.
xThe illumination of the headlights
is weakened because of dirt or the
optical axis is deviated at night.
xBack-light is reflected off the road
surface or the road surface is wet
and shiny after rain.
xThe shade of a guardrail parallel to
a white (yellow) lane line is cast on
the road.
xThe width of a lane is excessively
narrow or wide.
xThe road is excessively uneven.xThe vehicle is shaken after hitting a
road bump.
xThere are various road markings or
division lines (lane markings) of
various shapes near an
intersection.
xThe area in front of the camera is
soiled or an object that obstructs
the field of view is installed.
xExhaust gas from the vehicle in
front, sand, snow, and water
vapour rising from manholes and
grating, and water splashed into
the air.
xThe surroundings are dark such as
during the early evening or early
morning.
xA vehicle ahead with a certain tail
light shape.
xA vehicle ahead veers off course
from your vehicle's line of travel.
xA vehicle ahead is driving
erratically.
xThe vehicle is driven on roads with
tight curves.

Headway control function
If a vehicle ahead is detected while
travelling at a constant speed, the
vehicle-ahead indication is displayed
and headway control is performed.

Steering assist function
When lane lines are detected, the
function assists the driver in keeping
the vehicle within the lane lines. If lane
lines are not detected, the function
provides the driver driving assistance in
keeping the vehicle along the motion
path with the vehicle ahead.
When Driving
i-ACTIVSENSE
4-151

¾Do not adhere stickers (including
transparent stickers) to the surface of
the radiator grille and front emblem
in and around the front radar sensor,
and do not replace the radiator grille
and front emblem with any product
that is not a genuine product
designed for use with the front radar
sensor.
¾The front radar sensor includes a
function for detecting soiling of the
radar sensor's front surface and
informing the driver, however,
depending on the conditions, it may
require time to detect or it may not
detect plastic shopping bags, ice or
snow. If this occurs, the system may
not operate correctly, therefore
always keep the front radar sensor
clean.
¾Do not install a grille guard.
¾If the front part of the vehicle has
been damaged in a vehicle accident,
the position of the front radar sensor
may have moved. Stop the system
immediately and always have the
vehicle inspected at an expert
repairer (we recommend an
Authorised Mazda Repairer).
¾Do not use the front bumper to push
other vehicles or obstructions such
as when pulling out of a parking
space. Otherwise, the front radar
sensor could be hit and its position
deviated.
¾Do not remove, disassemble, or
modify the front radar sensor.
¾For repairs, replacement or paint
work around the front radar sensor,
consult an expert repairer (we
recommend an Authorised Mazda
Repairer).¾Do not modify the suspensions. If
the suspensions are modified, the
vehicle's posture could change and
the front radar sensor may not be
able to correctly detect a vehicle
ahead or an obstruction.
NOTE
xUnder the following conditions, the
front radar sensor may not be able to
detect vehicles ahead or obstructions
correctly and each system may not
operate normally.
xThe rear surface of a vehicle ahead
does not reflect radio waves
effectively, such as an unloaded
trailer or an automobile with a
loading platform covered by a soft
top, vehicles with a hard plastic
tailgate, and round-shaped
vehicles.
xVehicles ahead with low vehicle
height and thus less area for
reflecting radio waves.
xVisibility is reduced due to a
vehicle ahead casting
off water,
snow, or sand from its tyres and
onto your windscreen.
xThe luggage compartment is
loaded with heavy objects or the
rear passenger seats are occupied.
xIce, snow, or soiling is on the front
surface of the front emblem.
xDuring inclement weather such as
rain, snow, or sand storms.
xWhen driving near facilities or
objects emitting strong radio
waves.
xUnder the following conditions, the
front radar sensor may not be able to
detect vehicles ahead or
obstructions.
xThe beginning and end of a curve.xRoads with continuous curves.
When Driving
i-ACTIVSENSE
4-221

Owner Maintenance
Precautions
▼Owner Maintenance Precautions
Routine Service
We highly recommend that these items
be inspected daily, or at least every
week.
xEngine Oil Level (page 6-27)xEngine Coolant Level (page 6-28)xBrake and clutch Fluid Level (page
6-30)
xWasher Fluid Level (page 6-31)xBattery Maintenance (page 6-37)xTy re
Inflation Pressure (page 6-41)

Improper or incomplete service may
result in problems. This section gives
instructions only for items that are easy
to perform.

As explained in the Introduction (page
6-2), several procedures can be done
only by a
qualified service technician
with special tools.

Improper do-it yourself maintenance
during the warranty period may affect
warranty coverage. For details, read the
separate Mazda Warranty statement
provided with the vehicle. If you are
unsure about any servicing or
maintenance procedure, have it done
by an expert repairer (we recommend
an Authorised Mazda Repairer).

There are strict environmental laws
regarding the disposal of waste oil and
fluids. Please dispose of your waste
properly and with due regard to the
environment.

We recommend that you entrust the oil
and fluid changes of your vehicle to an
expert repairer (we recommend an
Authorised Mazda Repairer).
WARNING
Do not perform maintenance work if
you lack sufficient knowledge and
experience or the proper tools and
equipment to do the work. Have
maintenance work done by a
qualified technician:
Performing maintenance work on a
vehicle is dangerous if not done
properly. You can be seriously injured
while performing some maintenance
procedures.
If you must run the engine while
working under the bonnet, make
certain that you remove all jewellery
(especially rings, bracelets, watches,
and necklaces) and all neckties,
scarves, and similar loose clothing
before getting near the engine or
cooling fan which may turn on
unexpectedly:
Working under the bonnet with the
engine running is dangerous. It
becomes even more dangerous when
you wear jewellery, loose clothing or
have long hair or a long beard.
Either can become entangled in
moving parts and result in injury.
Maintenance and Care
Owner Maintenance
6-16

Engine oil viscosity, or thickness, has an effect on fuel economy and cold-weather
operation (starting and oil flow).
Low-viscosity engine oils can provide improved fuel economy and cold-weather
performance.

When choosing an oil, consider the temperature range your vehicle will operate in
before the next oil change.
Then select the recommended viscosity from the chart.
CAUTION
¾Using oils of viscosity besides those recommended for
specific temperature ranges
could result in engine damage.
¾(SKYACTIV-D 1.8)
SKYACTIV-D 1.8 uses specified oil. Please confirm the specification in owner's
manual. If engine oil other than the specified oil is used, the Diesel Particulate
Filter effective period of use will be shortened or the Diesel Particulate Filter may
be damaged.
NOTE
(SKYACTIV-G 2.0,
SKYACTIV-G 2.5, and
SKYACTIV-X 2.0)
xIt is normal for all engines to consume engine oil under normal driving conditions.
Engine oil consumption may be as high as 0.8 L/1,000 km (1 L/800 miles). This
may be as a result of evaporation, internal ventilation or burning of the lubricating
oil in the working engine. Oil consumption may be higher when the engine is new
due to the running-in process. Oil consumption is also dependant on engine
speed and engine load. Under extreme driving conditions, oil consumption may
be higher.
(SKYACTIV-D 1.8)
xInspect the engine oil level periodically. When inspecting the engine oil, if the
engine oil level exceeds the “X” mark on the dipstick, replace the engine oil.
When replacing the engine oil, inspect the oil level using the oil dipstick and refill
so that the engine oil level is within the range between MIN and MAX as shown in
the figure.
1. MIN
2. MAX
3. X Mark
Maintenance and Care
Owner Maintenance
6-26

Window and Headlight
Washer Fluid
▼Inspecting Washer Fluid Level
WARNING
Use only windscreen washer fluid or
plain water in the reservoir:
Using radiator antifreeze as washer
fluid is dangerous. If sprayed on the
windscreen, it will dirty the
windscreen, affect your visibility, and
could result in an accident.
Inspect fluid level in the washer fluid
reservoir; add fluid if necessary.

The top of the float should be between
F and E.

Use plain water if washer
fluid is
unavailable.
But use only washer fluid in cold
weather to prevent it from freezing.
NOTE
Front and rear washer
fluid is supplied
from the same reservoir.
Body Lubrication
▼Body Lubrication
All moving points of the body, such as
door and bonnet hinges and locks,
should be lubricated each time the
engine oil is changed. Use a
nonfreezing lubricant on locks during
cold weather.

Make sure the bonnet's secondary
latch keeps the bonnet from opening
when the primary latch is released.
Maintenance and Care
Owner Maintenance
6-31