brake light MAZDA MODEL CX-5 2013 Smart Start Guide (in English)

2
www.MazdaUSA.com
KEYLESS ENTRY SYSTEM
•
This system allows you to lock and unlock the doors by pushing the
desired buttons.
1
Key
Advanced Key
Electric Liftgate Opener
Lock
Unlock Panic Alarm
ADVANCED KEYLESS
ENTRY SYSTEM
• This system allows you to lock and
unlock the doors without taking the
key out.
While Carrying the
Advanced Key…
•
Unlock the driver’s door by
pushing the driver’s door request
switch once.
•
Unlock all doors (and liftgate)
by pushing the driver’s door request
switch once or twice (depending
on personalization setting, page
30) OR by pushing the passenger’s
door request switch once.
•
Lock all doors (and liftgate) by
pushing any request switch once.
•
Open the liftgate by pushing
the electric liftgate opener when
ignition is OFF. With ignition ON,
vehicle must be in Park (A / T) or
have parking brake set (M/ T).
NOTE:
When the liftgate opener switch is
pushed, the liftgate will open slightly. If the
liftgate is not opened within 1.5 seconds, the
liftgate latch locks (you will hear it lock) and
the liftgate cannot be opened or closed from
this slightly raised position. To open/close
the liftgate, push the liftgate opener switch,
open the liftgate within 1.5 seconds, then
close it. The door/liftgate ajar warning light
will be on if the liftgate is not fully closed.
Door Request Switch
Liftgate Request Switch
Unlock
• P u s h o n c e
to unlock
driver’s door
or all the doors
(depending on
personalization
setting).
• Push twice
(within three
seconds) to
unlock all doors
and liftgate.
Panic Alarm
•
Push for one
second or more
to activate alarm.
• Push Lock,
Unlock, or Panic
Alarm to turn
alarm off.
Lock
•
Push once to
lock all doors
and liftgate.
•
Push twice
(within five
seconds) for
horn sound
verification
that all doors
are locked.
NOTE:
Vehicles equipped with the Advanced Keyless Entry System and the Keyless
Entry System both use the same type of keyless entry transmitter. However, only vehicles
equipped with the Advanced Keyless Entry System allow you to lock and unlock the
doors/liftgate with the door/liftgate request switches (without taking the key out of your
purse or pocket).
Vehicles equipped with the Keyless Entry System do not have request switches on the
doors/liftgate. To lock and unlock the doors/liftgate, the corresponding transmitter button
must be pressed.
NOTE: Refer to your Owner’s Manual for additional details about
“Personalization Features”.
CAUTION: Make sure vehicle is OFF and take the keyless entry system
key with you when leaving the vehicle. There is no warning beep if the
IGN is ON or ACC is ON and the key is taken out of the vehicle, OR if
the key is locked inside the vehicle.
WARNING: RED
Key Indicator Light may illuminate if either advance
key or keyless entry key is placed in the cup holder. The cup holder is a
dead zone for transmitter reception.
Key
1191187_13c_Mazda_CX-5_SSG_062212.indd 2-36/22/12 2:46 PM

ACCELERATED WARM-UP SYSTEM (AWS)
Vehicle Starting:
Your vehicle is equipped with SKYACTIV combustion technology. This
technology includes AWS (Accelerated Warm-up System) for optimal
emission performance during cold starting conditions.
Cold Start (First start of the day on cold mornings):
Depress the brake (Automatic Trans.) or clutch (Manual Trans.), when the
key indicator light turns green
press the START/STOP button.
What you will notice: On start-up, the engine speed and sound are
higher (1500 RPM) for 30 seconds to 1 minute to quickly bring the catalyst
to efficient operating temperature. The RPM will reduce to idle once the
temperature is achieved. This is normal engine operation under cold
start conditions.
NOTE:
You can drive the vehicle during AWS activation, no need to wait.
Normal Start (Emission components within optimal
temperature range):
Depress the brake (Automatic Trans.) or clutch (Manual Trans.), when the
key indicator light turns green
press the START/STOP button.
4
www.MazdaUSA.com
3
Key
STARTING THE ENGINE
While Car rying the Key…
• Start the engine by pushing the START/STOP button, while
pushing the clutch pedal (manual transmission) or the brake pedal
(automatic transmission).
• Shut the engine OFF by placing the vehicle in Park, then push the
S TA R T/ S TO P b u t t o n .
• Activate Accessories (ACC) by pushing the START/STOP button
once without pushing the clutch or brake pedal.
• To turn the ignition to the ON position, push the START/STOP
button twice without pushing the clutch or brake pedal.
The key indicator light
in the instrument cluster will show GREEN (engine ready to start) when the key is detected and the clutch pedal (M/ T)
or the brake pedal (A / T) is pushed. If the KEY warning light illuminates
RED , or the START/STOP button indicator light flashes AMbER , this
could indicate a problem with the engine starting system and the inability
to start the engine or switch the ignition to ACC or ON. Have your vehicle
inspecte d at an Authorized Mazda Dealer as soon as possible.
Emergency Engine Start
If the engine cannot be started
due to a dead key battery:

1 Push the brake pedal (A / T)
or the clutch pedal (M/ T).
2 While the indicator light
light flashes GREEN , touch
the START/STOP button
using the back side of the
transmitter (as shown).
3 After the GREEN indicator
light illuminates constantly,
push the START/STOP
button with your finger
to start the engine.
Transmitter
Emergency Engine Stop:
Continuously pushing the START/
STOP button while the engine is
running will turn the engine OFF.
Use only in case of an emergency.
Emergency Vehicle Entry:
If the key cannot be used due to
a malfunction or dead key battery,
use the auxiliary key to lock or
unlock the doors.
Auxiliary Key Release
Auxiliary KeyKey (Rear)
START/STOP b utton
Indicator Light
Key
1191187_13c_Mazda_CX-5_SSG_062212.indd 4-56/22/12 2:46 PM

1112
SHIFT POSITION
INDICATOR LIGHT S
PEEDOMETERDASH bOARD
I LLUMINATION /
DIMMER
1/TRIP METER2 G LOSSARY OF W ARNING AND INDICATOR LIGHTS
NOTE: See Owner’s Manual for more details and explanations.
1 • Rotate the knob to adjust the brightness of the instrument cluster and other dashboard illuminations.2 • Push to toggle between trip meter (A & B).
• When a trip meter is selected, push and hold to reset to zero.
Instrument Cluster
NOTE: Low ambient temperature and/or high altitude causes tire pressures to drop and
may turn the TPMS warning light on. If the warning light comes on, check the tire pressure
and fill the tires as soon as possible, preferably before moving the vehicle and warming up
the tires. Tire pressure should be checked when the tires are cold.
www.MazdaUSA.com
TCS OFF

Traction Control System
(TCS) Off Indicator Light

Low Engine Oil Pressure

Traction Control System
(TCS)/Dynamic Stability
Control (DSC) On: TCS/DSC malfunction
Flashing: TCS/DSC operating
Shift Position Indicator Light
KEY Warning Light RED

KEY Indicator Light GREEN

Power Steering Malfunction

Air bag/Front Seat b
elt
Pretensioner System
Malfunction
Turn Signals/Hazard
Warning Indicator Lights
4WD
4WD Warning Light
On:
Flashing: Stop vehicle/tow to
Mazda dealer.
Check Engine Light

Master Warning Light

Tire Pressure

Monitoring System
(TPMS
) Warning Light On/ Warning Beep: Low tire
pressure in one or more tires.
Flashing: TPMS Malfunction

Security Indicator Light

Cruise Main Indicator Light

On (A M bER)/Cruise Set
Indicator Light On (G REEN)

Automatic Transaxle

Warning Light

Lights On (Exterior) bSM
OFF

b
SM OFF
( b lind Spot Monitoring)

Seat b
elt
Unbuckled/Malfunction

Headlight High b
eams On

b
rake Warning Light Parking brake on/low brake
fluid/malfunction
AFS
OFF

Adaptive Front Lighting
System (AFS) OFF

Charging System
Malfunction
Door/Liftgate Ajar

Low Washer Fluid Level
Warning Light

A b S (Antilock b rake
System) Malfunction

Low Fuel Level

Check Fuel Cap
T
ACHOMETER
F UEL
GAUGE
ODOMETER/

TRIP METER
E NGINE C OOLANT T EMP LIGHTS Since this vehicle does not use an engine coolant
temperature gauge, red and blue engine coolant
temperature lights are used to indicate high and low
coolant temperature.
Red Coolant Temp Light
Flashing: Engine is starting to run hot. Drive
slowly to reduce engine load.
On: Engine is overheating. Safely pull over to
the side of the road and turn the engine off.

Refer to the Owner’s Manual for more information.
b lue Coolant Temp Light
On: Engine coolant is cold and no warm air is
available for heater/defroster.
Off: Engine coolant is warm and warm air is
available for heater/defroster.
The light may stay on for a few minutes after
start-up when the engine is cold, but the
vehicle can be driven with the light on or off.
INFORMATION D I S P L AYAM bIENT
T EMPERATURE
See page 8 or the
Owner’s Manual for
further information.
1191187_13c_Mazda_CX-5_SSG_062212.indd 12-136/22/12 2:47 PM

1516
Transmissionwww.MazdaUSA.com
SPORT A/T MANUAL SHIFT MODE
The Sport A/T Manual Shift Mode gives you the
feel of driving a manual transmission by allowing
you to manually shift to control engine rpm and
torque when more control is desired.
To Use Manual Shift Mode:
• Shift the lever from D to M.
NOTE:
Changing to manual
mode can be done while driving
the vehicle.
To Shift Up To A Higher Gear:
• Tap shift lever back (+) once.
To Shift Down To A Lower Gear:
• Tap shift lever forward (-) once.
ACTIVE ADAPTIVE SHIFT (AAS) CONTROL
The transmission will automatically adjust how and when it shifts gears
based on road conditions and your driving style. The transmission may stay
in a lower gear longer than usual when going up or down hills or driving
around corners. This feature gives you better control and a more connected
driving experience.
6-SPEED MANUAL TRANSMISSION
• Push the clutch pedal completely down
to start the engine and to shift gears.
• To place the transmission in Reverse,
place shifter in the neutral position,
push the shifter knob down, move to
the left and push forward.

Auto-Dimming Mirror
• Auto-dimming will automatically darken your rearview mirror to reduce
headlight glare from vehicles behind you.
•
Auto-dimming is activated every time the engine is started.
NOTE:
In addition to the auto-dimming mirror’s rear light sensor, there is also a front light sensor (not shown). Do not place or hang any objects over the front or rear
mirror light sensors; otherwise, the auto-dimming mirror will not operate properly.
HomeLink®
•
This feature provides a convenient way to replace up to three
transmitters such as garage door openers, home lighting remotes
and other radio frequency devices.
• Refer to your Owner’s Manual for complete programming details.
NOTE:
Genuine Mazda Accessory Auto-Dimming Mirror with Compass and
Homelink is available at your Authorized Mazda Dealer.
A UTO -DIMMING MIRROR AND HOME LINK®
Auto-Dimming
Indicator LightAuto-Dimming
On
HomeLinkRear
Light
SensorAuto-Dimming
Off
On Off
H ILL L AUNCH A SSIST (HLA)
This feature helps assist you when accelerating the vehicle from a stop while
on a hill or slope. When the brake pedal is released and the accelerator
pedal is pressed, HLA prevents the vehicle from rolling forward or backward.
It operates on a downward slope when the shift lever is in the reverse (R)
position, and on an upward slope when the shift lever is in a position other
than the reverse (R) position.
NOTE:
The HL A system will hold the vehicle for a maximum of 2.0 seconds while
the driver is changing from the brake pedal to the accelerator pedal.
S ETTING YOUR CLOCK
•
Push the H button to set the hour.
• Push the M button to set the minutes.
Push the :00 button to reset clock to
nearest hour.
Lower Gear
Higher Gear
With b rake
Pressed
Mirrors
1191187_13c_Mazda_CX-5_SSG_062212.indd 16-176/22/12 2:48 PM

2122
www.MazdaUSA.comLights
TIRE PRESSURE MONITORING SYSTEM (TPMS)
Your vehicle is equipped with a Tire Pressure Monitoring System (TPMS)
that detects low tire pressure in one or more tires. In the following cases,
the TPMS must be “initialized” so the system can operate normally.
• The tire pressure is adjusted (up or down) in one or more tires.
• A tire rotation is performed.
•
Any tire or wheel is replaced.
•
The vehicle’s battery is disconnected, replaced or completely dead.
Initialization Process (TPMS Warning Light is Illuminated):
1
Park the vehicle in a safe place and firmly apply the parking brake.
2
Let the tires cool, then adjust the tire pressure to the specified
pressure (Refer to your Owner’s Manual for correct tire pressure) on
all four (4) tires.
3
Switch the ignition ON, but leave the vehicle parked.
4
Push and hold the TPMS “Set Switch” (left side of dash)
until the TPMS warning light
in the instrument cluster

flashes twice and a beep sound is heard once.
CAUTION: If the TPMS “Set Switch” is pressed without adjusting the tire
pressure, the system cannot detect the normal tire pressure. The TPMS
warning light may not illuminate, even if the tire pressure is low, or it may
illuminate if the tire pressure is normal.
Wheels
Push AFS OFF to turn system off or on. When off, AFS OFF
illuminates in the instrument panel.
With AFS
Without AFS
Genuine Mazda Accessory
Wheel Locks are available at
your Authorized Mazda Dealer
Your aluminum wheels have a protective
coating on them. Only use a mild soap or
neutral detergent with a sponge or soft cloth
to clean them.
CAUTION: Using a wire brush, polishing
compound, solvent, or any type of abrasive
cleaner may damage the protective coating.
ALUMINUM WHEEL CARE
A DAPTIVE FRONT-LIGHTING SYSTEM (AFS)
The adaptive front-lighting system (AFS) automatically turns the headlight
beam to the right or left in conjunction with the direction of the steering
wheel. The AFS improves the direction of headlight illumination while
cornering, and only works when the vehicle is moving.
NOTE:

•
With AFS, it is normal to see the headlights move and hear the sound of the
headlight leveling motors at the front of the vehicle when the ignition is ON.
•
The system will need to be reset if the vehicle battery has been disconnected
or the system fuse has been replaced. Please refer to your Owner’s Manual for
easy to follow resetting instructions.
1191187_13c_Mazda_CX-5_SSG_062212.indd 22-236/22/12 2:48 PM