MAZDA MODEL CX-5 2016 Owners Manual (in English)

Black plate (221,1)
All-Wheel Drive (AWD)
Operation
lAWD provides excellent drivability on
snow-covered and ice-packed roads,
sand and mud, as well as on steep
slopes and other slippery surfaces.
lA system malfunction or operation
conditions are indicated by a warning.
Refer to Warning/Indicator Lights on
page 4-20.
WARNING
Never spin a wheel that is off the
ground:
Spinning a wheel that is off the
ground as a result of the vehicle
being stuck or in a ditch is
dangerous. The drive assembly could
be seriously damaged which could
lead to an accident or could even
lead to overheating, oil leakage, and
a fire.
qAWD Driving
WARNING
Avoid sharp turns, excessive speed and
abrupt maneuvers when driving this
vehicle:
Sharp turns, excessive speed and
abrupt maneuvering of this vehicle is
dangerous as it could result in the
increased risk of loss of vehicle
control, vehicle roll-over, personal
injury or death.
This vehicle has a higher center of
gravity. Vehicles with a higher center
of gravity such as utility and AWD
vehicles handle differently than
vehicles with a lower center of
gravity.
Utility and AWD vehicles are not
designed for cornering at high speeds
any more than low profile sports cars
are designed to perform satisfactorily
under off-road conditions. In
addition, utility vehicles have a
significantly higher rollover rate than
other types of vehicles.
Drive carefully when the vehicle is
loaded by lowering vehicle speed and
applying the brakes earlier:
Abrupt maneuvering and sudden
braking when driving a loaded
vehicle is dangerous as the driving
behavior of a vehicle with a high
center of gravity is different when it is
loaded compared to when it is not,
and could result in the loss of vehicle
control and an accident.
When Driving
AW D
4-87
CX-5_8DV2-EA-14K_Edition3 Page221
Thursday, February 26 2015 5:32 PM
Form No.8DV2-EA-14K

Black plate (222,1)
qTires and Tire Chains
The condition of the tires plays a large
role in the performance of the vehicle.
Moreover, to prevent adverse effects to
the drive assembly, please note the
following:
Tires
lWhen replacing tires, always replace
all front and rear tires at the same time.
lAll tires must be of the same size,
manufacture, brand and tread pattern.
Pay particular attention when
equipping snow or other types of
winter tires.
lDo not mix tread-worn tires with
normal tires.
lInspect tire inflation pressures at the
specified periods adjust to the specified
pressures, and initialize the tire
pressure monitoring system.
NOTE
Check the tire inflation pressure label attached
to driver's door frame for the correct tire
inflation pressure.
lMake sure to equip the vehicle with
genuine wheels of the specified size,
on all wheels. With AWD, the system
is calibrated for all four wheels being
of the same dimensions.
Tire chains
lInstall tire chains to the front tires.lDo not use tire chains on the rear
wheels.
lDo not drive the vehicle faster than 30
km/h (19 mph) with the tire chains
installed.
lDo not drive the vehicle with tire
chains on road conditions other than
snow or ice.
qTowing
If the vehicle requires towing, have it
towed with all four wheels completely off
the ground(page 7-20).
4-88
When Driving
AW D
CX-5_8DV2-EA-14K_Edition3 Page222
Thursday, February 26 2015 5:32 PM
Form No.8DV2-EA-14K

Black plate (223,1)
Power Steering
lPower steering is only operable when
the engine is running. If the engine is
off or if the power steering system is
inoperable, you can still steer, but it
requires more physical effort.
If the steering feels stiffer than usual
during normal driving or the steering
vibrates, consult an Authorized Mazda
Dealer.
lFor vehicles with the type A instrument
cluster, check the vehicle condition or
have the vehicle inspected at an
Authorized Mazda Dealer according to
the indication.
lA system malfunction or operation
conditions are indicated by a warning.
In addition, the buzzer may also
activate depending on the system
abnormality or operation condition.
Refer to Warning/Indicator Lights on
page 4-20.
Refer to Warning Sound is Activated
on page 7-34.
CAUTION
Never hold the steering wheel to the
extreme left or right for more than 5
seconds with the engine running.
This could damage the power
steering system.
When Driving
Power Steering
4-89
CX-5_8DV2-EA-14K_Edition3 Page223
Thursday, February 26 2015 5:32 PM
Form No.8DV2-EA-14K

Black plate (224,1)
i-ACTIVSENSEí
i-ACTIVSENSE is a collective term covering a series of advanced safety and driver
support systems which make use of a Forward Sensing Camera (FSC) and radar sensors.
These systems are designed to assist the driver in safer driving by reducing the load on the
driver and helping to avert collisions or reduce their severity. However, because each
system has its limitations, always drive carefully and do not rely solely on the systems.
qActive Safety Technology
Active Safety Technology supports safer driving by helping the driver to recognize
potential hazards and avert accidents.
Driver awareness support systems
Nighttime visibility
Adaptive Front Lighting System (AFS) ................................................................. page 4-92
High Beam Control System (HBC) ........................................................................ page 4-93
Left/right side and rear side detection
Lane Departure Warning System (LDWS) ............................................................. page 4-96
Blind Spot Monitoring (BSM) System ................................................................. page 4-102
Inter-vehicle distance recognition
Distance Recognition Support System (DRSS) ................................................... page 4-108
Rear obstruction detection when leaving a parking space
Rear Cross Traffic Alert (RCTA) ......................................................................... page 4-111
Driver Support Systems
Inter-vehicle distance
Mazda Radar Cruise Control (MRCC) ................................................................. page 4-116
qPre-Crash Safety Technology
Pre-crash safety technology is designed to assist the driver in averting collisions or reduce
their severity in situations where they cannot be avoided.
Collision damage reduction in low vehicle speed range
Forward driving
Smart City Brake Support (SCBS) ....................................................................... page 4-126
Collision damage reduction in medium/high speed range
Smart Brake Support (SBS) ................................................................................. page 4-131
4-90
When Driving
íSome models.
i-ACTIVSENSE
CX-5_8DV2-EA-14K_Edition3 Page224
Thursday, February 26 2015 5:32 PM
Form No.8DV2-EA-14K

Black plate (225,1)
qCamera and Sensors
Forward Sensing Camera (FSC)
The Forward Sensing Camera (FSC) detects lane indications and recognizes headlights,
taillights and city lights during nighttime driving. The following systems also use the
Forward Sensing Camera (FSC).
lHigh Beam Control system (HBC)lLane Departure Warning System (LDWS)lSmart Brake Support (SBS)
The Forward Sensing Camera (FSC) is installed at the top of the windshield near the
rearview mirror.
Refer to Forward Sensing Camera (FSC) on page 4-134.
Radar sensor (front)
The radar sensor (front) functions by detecting the radio waves reflected off a vehicle
ahead sent from the radar sensor. The following systems also use the radar sensor (front).
lMazda Radar Cruise Control (MRCC)lDistance Recognition Support System (DRSS)lSmart Brake Support (SBS)
The radar sensor (front) is mounted behind the radiator grille.
Refer to Radar Sensor (Front) on page 4-137.
Laser sensor (front)
The laser sensor (front) emits a near-infrared laser beam and receives the beam reflected off
the reflective surface of a vehicle in front, and the detected beam is then used for
measurement. The following systems also use the laser sensor (front).
lSmart Brake Support (SBS)lSmart City Brake Support (SCBS)
The laser sensor (front) is installed at the top of the windshield near the rearview mirror.
Refer to Laser Sensor (Front) on page 4-140.
Radar sensors (rear)
The radar sensors (rear) function by detecting the radio waves reflected off a vehicle
approaching from the rear or an obstruction sent from the radar sensors. The following
systems also use the radar sensors (rear).
lBlind Spot Monitoring (BSM) SystemlRear Cross Traffic Alert (RCTA)
The radar sensors (rear) are installed inside the rear bumper, one each on the left and right
sides.
Refer to Radar Sensors (Rear) on page 4-142.
When Driving
i-ACTIVSENSE
4-91
CX-5_8DV2-EA-14K_Edition3 Page225
Thursday, February 26 2015 5:32 PM
Form No.8DV2-EA-14K

Black plate (226,1)
Adaptive Front Lighting
System (AFS)
í
The adaptive front lighting system (AFS)
automatically adjusts the headlight beams
to the left or right in conjunction with the
operation of the steering wheel after the
headlights have been turned on and the
vehicle speed is about 2 km/h (2 mph) or
higher.
A system malfunction or operation
conditions are indicated by a warning.
Refer to Warning/Indicator Lights on page
4-20.
NOTE
The Adaptive Front Lighting System (AFS)
function can be switched to operable/
inoperable using the personalization function.
Refer to Personalization Features on page
9-10.
4-92
When Driving
íSome models.
i-ACTIVSENSE
CX-5_8DV2-EA-14K_Edition3 Page226
Thursday, February 26 2015 5:32 PM
Form No.8DV2-EA-14K

Black plate (227,1)
High Beam Control System (HBC)í
The High Beam Control System (HBC) determines the conditions in front of the vehicle
using the Forward Sensing Camera (FSC) while driving in darkness to automatically
switch the headlights between high and low beams.
Refer to Warning/Indicator Lights on page 4-20.
While driving the vehicle at a speed of about 30 km/h (18 mph), the headlights are
switched to high beams when there are no vehicles ahead or approaching in the opposite
direction.
The system switches the headlights to low beams when one of the following occurs:
lThe system detects a vehicle or the headlights/lights of a vehicle approaching in the
opposite direction.
lThe vehicle is driven on roads lined with streetlamps or on roads in well-lit cities and
towns.
lThe vehicle is driven at less than about 20 km/h (12 mph).
Forward Sensing
Camera (FSC)
The recognition distance of the
Forward Sensing Camera (FSC)
varies according to the
surrounding conditions.
The warning light illuminates or flashes when the system has a malfunction.
Refer to Warning/Indicator Lights on page 4-20.
CAUTION
ØDo not adjust the vehicle height, modify the headlight units, or remove the
camera, otherwise the system will not operate normally.
ØDo not rely excessively on the High Beam Control System (HBC) and drive the
vehicle while paying sufficient attention to safety. Switch the headlights between
the high beams and low beams manually if necessary.
When Driving
i-ACTIVSENSE
4-93íSome models. CX-5_8DV2-EA-14K_Edition3 Page227
Thursday, February 26 2015 5:32 PM
Form No.8DV2-EA-14K

Black plate (228,1)
NOTE
The timing in which the system switches the headlights changes under the following conditions. If the
system does not switch the headlights appropriately, manually switch between high and low beams
according to the visibility as well as road and traffic conditions.
lWhen there are sources of light in the area such as street lamps, illuminated signboards, and
traffic signals.
lWhen there are reflective objects in the surrounding area such as reflective plates and signs.lWhen visibility is reduced under rain, snow and foggy conditions.lWhen driving on roads with sharp curves or hilly terrain.lWhen the headlights/rear lamps of vehicles in front of you or in the opposite lane are dim or not
illuminated.
lWhen there is insufficient darkness such as at dawn or dusk.lWhen the luggage compartment is loaded with heavy objects or the rear passenger seats are
occupied.
lWhen visibility is reduced due to a vehicle in front of you spraying water from its tires onto your
windshield.
4-94
When Driving
i-ACTIVSENSE
CX-5_8DV2-EA-14K_Edition3 Page228
Thursday, February 26 2015 5:32 PM
Form No.8DV2-EA-14K

Black plate (229,1)
qTo Operate the System
The High Beam Control System (HBC)
operates to switch the headlights
automatically between high and low
beams after the ignition is switched ON
and the headlight switch is in the AUTO
and high beam position. At the same time,
the High Beam Control System (HBC)
indicator light (green) in the instrument
cluster illuminates.
The High Beam Control System (HBC)
determines that it is dark based on the
brightness of the surrounding area.
NOTE
lWhen the vehicle speed is 30 km/h (18 mph)
or higher, the headlights automatically
switch to high beams when there are no
vehicles ahead or approaching in the
opposite direction.
When the vehicle speed is less than about
20 km/h (12 mph), the High Beam Control
System (HBC) switches the headlights to
low beams.
lThe low beams may not switch to high
beams when cornering.
lOperation of the High Beam Control
System (HBC) function can be disabled
Refer to Personalization Features on page
9-10.
qManual Switching
Switching to low beams
Shift the lever to the low beam position.
The High Beam Control System (HBC)
indicator light (Green) turns off.
Switching to high beams
Turn the headlight switch to the
position.
The High Beam Control System (HBC)
indicator light (Green) turns off and the
is illuminated.
When Driving
i-ACTIVSENSE
4-95
CX-5_8DV2-EA-14K_Edition3 Page229
Thursday, February 26 2015 5:33 PM
Form No.8DV2-EA-14K

Black plate (230,1)
Lane Departure Warning System (LDWS)í
The LDWS system notifies the driver that the vehicle may be deviating from its lane.
The system detects the white or yellow lines on the traffic lane using the forward sensing
camera and if it determines that the vehicle may be deviating from its lane, it notifies the
driver using the multi-information display (vehicles with type A instrument cluster), and by
flashing the LDWS warning light (vehicles with type B instrument cluster) and activating
the LDWS warning beep.
Use the LDWS when you drive the vehicle on roads with white or yellow lines.
Refer to Forward Sensing Camera (FSC) on page 4-134.
Forward Sensing Camera (FSC)
Vehicles with type A instrument cluster
The LDWS OFF indication illuminates when the system has a malfunction.
Vehicles with type B instrument cluster
The LDWS warning light illuminates when the system has a malfunction.
Refer to Warning/Indicator Lights on page 4-20.
4-96
When Driving
íSome models.
i-ACTIVSENSE
CX-5_8DV2-EA-14K_Edition3 Page230
Thursday, February 26 2015 5:33 PM
Form No.8DV2-EA-14K