warning MAZDA MODEL CX-5 2017 Owner's Manual - RHD (UK, Australia) (in English)

NOTE
The initialization (engine oil data resetting) of the recorded value can be performed using
the following procedure:
1. Switch the ignition OFF.
2. Switch the ignition ON with the instrument panel illumination knob pressed, and press and hold the instrument panel illumination knob for about 5 seconds until the master
warning light
flashes.

Instrument panel illumination knob
3. After the master warning light flashes for several seconds, the initialization is
completed.
▼ Inspecting Engine Oil Level
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal operating temperature.
3. Turn it off and wait at least 5 minutes for the oil to return to the sump.
4. Pull out the dipstick, wipe it clean, and
reinsert it fully.
SKYACTIV-G 2.0 and
SKYACTIV-G 2.5

MAX
OK
MIN
Maintenance and Care
Owner Maintenance
6-28
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

3. If any fuse but the MAIN fuse isblown, replace it with a new one of the
same amperage rating .
NormalBlown
WARNING
Do not replace the main fuse by
yourself. Have an Authorised Mazda
Repairer perform the replacement:
Replacing the fuse by yourself is
dangerous because the MAIN fuse is a
high current fuse. Incorrect
replacement could cause an electrical
shock or a short circuit resulting in a
fire.
4. Reinstall the cover and make sure that it is securely installed.
▼Fuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1
50 A For protection of various circuits
2 IG2 30 A For protection of various circuits
Maintenance and Care
Owner Maintenance
6-56
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

DESCRIPTIONFUSE
RATING PROTECTED COMPONENT
35 ST.HEATER 15 A Heated steering wheel
*
36FOG 15 A
Fog lights*
377.5 A Engine control system
38 H/L LOW L 15 A Headlight low beam (LH)
39 ENGINE4 15 A Engine control system
*
40― ― ―
41 METER1 10 A Instrument cluster
42 SRS1 7.5 A Air bag
43 BOSE 25 A
Bose
® Sound System-equipped model*
44 AUDIO1 15 A Audio system
45 ABS/DSC S 30 A ABS, Dynami c stability control system
46 FUEL PUMP 15 A Fuel system
*
47 FUEL WARM 25 AFuel warmer*
48TAIL 15 A Tail lights, Number plate lights
49 SCR2
FUEL PUMP2 25 A
Fuel system
*
50 HAZARD 25 A Hazard warning flashers, Direc
tion indicator lights, Tail lights,
Position lights
51 H/L LOW R 15 A Headlight low beam (RH)
52 OUTLET 25 A Accessory sockets
53 STOP 10 A Brake lights
54 ROOM 15 A Overhead light
Maintenance and Care
Owner Maintenance
6-58*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Wa t e r M a r k s
Occurrence
Rain, fog, dew, and even tap water can
contain harmful minerals such as salt and
lime. If moisture containing these minerals
settles on the vehicle and evaporates, the
minerals will concentrate and harden to
form white rings. The rings can damage
your vehicle's finish.
Prevention
It is necessary to wash and wax your
vehicle to preserve its finish according to
the instructions in this section. These steps
should be taken immediately after you find
water marks on your vehicle's finish.
Paint Chipping
Occurrence
Paint chipping occurs when gravel thrown
in the air by another v ehicle's tyres hits
your vehicle.
How to avoid paint chipping
Keeping a safe distance between you and
the vehicle ahead reduces the chances of
having your paint chipped by flying
gravel.
NOTE
•The paint chipping zone varies with the
speed of the vehicle. For example, when
travelling at 90 km/h (56 mph), the paint
chipping zone is 50 m (164 ft).
•In low temperatures a vehicle's finish
hardens. This increases the chance of
paint chipping.
•Chipped paint can lead to rust forming
on your Mazda. Before this happens,
repair the damage by using Mazda
touch-up paint according to the
instructions in this section. Failure to
repair the affected area could lead to
serious rusting and expensive repairs.

Follow all label and container directions
when using a chemical cleaner or polish.
Read all warnings and cautions.
▼ Maintaining the Finish
Wa s h i n g
CAUTION

When the wiper lever is in the
position and the ignition is switched ON,
the wipers may move automatically in
the following cases:
 If the windscreen above the rain sensor
is touched or wiped with a cloth.
 If the windscreen is struck with a hand
or other object from either outside or
inside the vehicle.
Keep hands and scrapers clear of the
windscreen when the wiper lever is in the
position and the ignition is
switched ON as fingers could be pinched
or the wipers and wiper blades damaged
when the wipers activate automatically.
If you are going to clean the windscreen,
be sure the wipers are turned off
completely (when it is most likely that the
engine is left running) this is particularly
important when clearing ice and snow.
Maintenance and Care
Appearance Care
6-62
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

7If Trouble Arises
Helpful information on what to do if a problem arises with the vehicle.
Mazda ERA-GLONASS
(Russia)............................................... 7-2 Mazda ERA-GLONASS.............. 7-2
Indicator Light/Beep Sound....... 7-10
Test Mode................................... 7-11
Parking in an Emergency............... 7-14 Parking in an Emergency............7-14
Roadside Emergency Triangle
Retaining Strap
*......................... 7-14
Flat Tyre........................................... 7-15 Spare Tyre and Tool Storage...... 7-15
Emergency Flat Tyre Repair Kit
*......
.................................................... 7-19
Changing a Flat Tyre (With Spare
Tyre)........................................... 7-26
Battery Runs Out............................ 7-32 Jump-Starting............................. 7-32
Emergency Starting.........................7-35 Starting a Flooded Engine
(SKYACTIV-G 2.0 and SKYACTIV-
G 2.5).......................................... 7-35
Push-Starting.............................. 7-35
Running Out of Fuel (SKYACTIV-D
2.2).............................................. 7-36
Overheating......................................7-37
Overheating................................ 7-37
Emergency Towing.......................... 7-39 Towing Description.................... 7-39
Towing Hooks......... ................... 7-41
Warning/Indicator Lights and
Warning Sounds.............................. 7-43 If a Warning Light Turns On or
Flashes........................................ 7-43
Message Indicated in Multi-
information Display.................... 7-59
Message Indicated on
Display........................................7-61
Warning Sound is Activated....... 7-63
When Liftgate Cannot be
Opened..............................................7-70 When Liftgate Cannot be
Opened........................................7-70
Active Driving Display Does Not
Operate............................................. 7-71 If the Active Driving Display Does
Not Operate................................ 7-71
*Some models.7-1
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

After that, perform the following procedure.
Move the signal lever up to right
turn
Move the signal lever up to right
turn Move the signal lever down
to left turn
Move the signal lever down
to left turn
Return the signal lever to off
Return the signal lever to off
Return the signal lever to off
Return the signal lever to off
Return the signal lever to off
Move the signal lever up to right
turn Within five seconds
Within one second Within one second Within one second
Within one second
Within one second
Within one second
Within one second
Within one second Within five seconds
Within five second
Within one second
Turn on the hazard warning
lights.
Turn off the hazard warning
lights.
Both red and green Mazda
ERA-GLONASS switch
indicator lights turn on.
Press the Mazda
ERA-GLONASS switch for
one second or longer and
release it.
If Trouble Arises
Mazda ERA-GLONASS (Russia)
7-12
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Parking in an Emergency
The hazard warning lights should always
be used when you stop on or near a
roadway in an emergency.

The hazard warning lights warn other
drivers that your vehicle is a traffic hazard
and that they must take extreme caution
when near it.

Depress the hazard warning flasher and all
the direction indicators will flash. The
hazard warning indicator lights in the
instrument cluster flash simultaneously.
NOTE
•The direction indicators do not work
when the hazard warning lights are on.
•Check local regulations about the use of
hazard warning lights while the vehicle
is being towed to verify that it is not in
violation of the law.
Roadside Emergency
Triangle Retaining Strap
*
Keep the roadside emergency triangle in
the left side trim and secure it with the
strap.
Strap
If Trouble Arises
Parking in an Emergency
7-14*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼About the Emergency Flat Tyre
Repair Kit
The emergency flat tyre
repair kit includes
the following items.

Tyre sealant Injection hose
Compressor Valve core
tool
Spare valve
core
Speed restriction
sticker
Instructions
WA R N I N G
Do not allow children to touch the tyre
sealant:

Ingestion of tyre sealant is dangerous. In
the event tyre sealant is accidentally
swallowed, drink large amounts of water
immediately and seek medical
assistance.
 Tyre sealant that comes into contact
with the eyes and skin is dangerous. If
tyre sealant enters the eyes or contacts
the skin, flush immediately with large
amounts of water and seek medical
assistance.
NOTE
•The tyre sealant cannot be reused.
Purchase new tyre sealant at an
Authorised Mazda Repairer.
•The emergency flat tyre repair kit cannot
be used in the following cases.
Consult an expert repairer, we
recommend an Authorised Mazda
Repairer.
•The period of effective use for the tyre
sealant has expired. (The period of
effectiveness is indicated on the bottle
label.)
•The tear or puncture exceeds about 4
mm (0.16 in).
•The damage has occurred to an area
of the tyre other than the tread.
•The vehicle has been driven with
nearly no air remaining in the tyre.
•The tyre has come off the wheel rim.
•Damage to the wheel rim has
occurred.
•The tyre has two or more punctures.
▼ Using the Emergency Flat Tyre
Repair Kit
1. Park on a level surface off the
right-of-way and set the parking brake.
2. Put a vehicle with an automatic
transaxle in Park (P), a manual
transaxle in Reverse (R) or 1, and turn
off the engine.
3. Turn on the hazard warning flasher.
If Trouble Arises
Flat Tyre
7-20
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

WARNING
Never operate the compressor above
300 kPa (3.1 kgf/ c m
2, 3 bar, 43.5 psi):
Operating the compressor above 300
kPa (3.1 kgf/cm
2, 3 bar, 43.5 psi) is
dangerous. When the inflation pressure
rises above 300 kPa (3.1 kgf/cm
2, 3 bar,
43.5 psi), heated air will be exhausted
from the back of the compressor and
you could be burned.
NOTE
•Check the tyre inflation pressure
label (driver's door frame) for the
correct tyre inflation pressure.
•Do not use the compressor for
longer than 10 minutes because
using the compressor for long
periods could damage it.
•If the tyre does not inflate, repair of
the tyre may not be possible. If the
tyre does not reach the correct
inflation pressure within a 10-minute
period, it probably has received
more extensive damage. When this
happens, the emergency flat tyre
repair kit cannot be used to repair
the tyre. Contact an expert repairer,
we recommend an Authorised Mazda
Repairer.
•If the tyre has been over-inflated,
loosen the screw cap on the
compressor and bleed some of the
air out.
16. When the tyre has been inflated to the proper inflation pressure, turn the
compressor switch off and remove the
compressor hose from the tyre valve.
17. Install the tyre valve cap.
18. Put the emergency flat tyre repair kit in the boot and continue driving.
CAUTION
Drive carefully to an expert repairer,
we recommend an Authorised
Mazda Repairer and keep the vehicle
speed below 80 km/h (50 mph).
 If the vehicle is driven 80 km/h (50
mph) or higher, the vehicle might
begin to vibrate.
NOTE
(With Tyre Pressure Monitoring
System)
If the tyre is not properly inflated, the
tyre pressure monitoring system
warning light will illuminate (page
4-42).
19. After driving the vehicle for 10 minutes or 5 km (3 miles), check the
tyre pressure with the tyre pressure
gauge equipped with the compressor. If
the tyre pressure ha s fallen below the
correct tyre pressure, inflate the tyre to
the correct pressure again following
the steps from number 14.
CAUTION
 If the tyre inflation pressure falls
below 130 kPa (1.3 kgf/cm
2 or bar,
18.9 psi), repair cannot be done with
the repair kit. Park the vehicle on a
level surface off the right-of-way and
contact an expert repairer, we
recommend an Authorised Mazda
Repairer.
If Trouble Arises
Flat Tyre
7-24
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Changing a Flat Tyre(With Spare Tyre)
NOTE
If the following occurs while driving, it
could indicate a flat tyre.
•Steering becomes difficult.
•The vehicle begins to vibrate
excessively.
•The vehicle pulls in one direction.
If you have a flat tyre, drive slowly to a
level spot that is well off the road and out
of the way of traffic to change the tyre.
Stopping in traffic or on the shoulder of a
busy road is dangerous.
WA R N I N G
Be sure to follow the directions for
changing a tyre:
Changing a tyre is dangerous if not done
properly. The vehicle can slip off the jack
and seriously injure someone.
No person should place any portion of their
body under a vehicle that is supported by a
jack.
Never allow anyone inside a vehicle
supported by a jack:
Allowing someone to remain in a vehicle
supported by a jack is dangerous. The
occupant could cause the vehicle to fall
resulting in serious injury.
NOTE
Make sure the jack is well lubricated
before using it.
1. Park on a hard, level surface off the right-of-way and firml y set the parking
brake.
2. Put a vehicle with an automatic transaxle in Park (P), a manual
transaxle in Reverse (R) or 1, and turn
off the engine.
3. Turn on the hazard warning flasher.
4. Have everyone get out of the vehicle
and away from the vehicle and traffic.
5. Remove the jack, tool, and spare tyre
(page 7-15).
6. Block the wheel diagonally opposite the flat tyre. When blocking a wheel,
place a tyre block both in front and
behind the tyre.
NOTE
When blocking a tyre, use rocks or
wood blocks of sufficient size if
possible to hold the tyre in place.
If Trouble Arises
Flat Tyre
7-26
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2