oil MAZDA MODEL CX-5 2017 Owner's Manual - RHD (UK, Australia) (in English)

NOTE
When you fold down the left seatback, the
centre seatback folds down at the same
time.
Using remote handle
*
1.(With rear seat warmer)
Turn the rear seat warmer switch off.
Refer to Seat Warmer on page 2-14.
2. After checking that the rear seats are
clear, open the liftgate and lower the
seatback you want to fold down using
the remote handle.
When folding the left side, operate the
outer part of the remote handle.
WA R N I N G
Always remove the child-restraint system
from the rear seat before operating the
remote handle for the rear seat:
Operating the remote handle while a
rear-facing child-restraint system is in the
rear seat is dangerous. It could cause injury
to a child seated in the child-restraint
system when the seatback suddenly flips
forward.
Make sure there is nobody in the rear seat
area before operating (pulling) the remote
handle:
Not checking the rear seat area for persons
before folding the seatbacks with the strap/
remote handle is dangerous. The rear seat
area is difficult to see from the rear of the
vehicle. Operating (pulling) the remote
handle without checking could cause injury
to a person when a se atback suddenly flips
forward.
CAUTION
 Before folding the seatbacks down with
the remote handle, make sure there is no
cup in a rear cup holder. Folding the
seatbacks with the remote handle while
a cup is in the cup holder could soil or
damage the seat bottom and seatback.
 Be careful of the following when using
the remote handle:
 On a downward slope, the seatback
could flip forward faster than on a flat
surface.
 On an upward slope, the seatback may
not fold down. When the seatbacks
cannot be folded down with the
remote handle, pull the rear seatback
forward from inside the vehicle.
Essential Safety Equipment
Seats
2-10*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

CAUTION
Before folding the seatbacks down with
the remote handle, make sure there is no
cup in a rear cup holder. Folding the
seatbacks with the remote handle while
a cup is in the cup holder could soil or
damage the seat bottom and seatback.
 Be careful of the following when using
the remote handle:
 On a downward slope, the seatback
could flip forward faster than on a flat
surface.
 On an upward slope, the seatback may
not fold down. When the seatbacks
cannot be folded down with the
remote handle, pull the rear seatback
forward from inside the vehicle.
Using strap
1. (With rear seat warmer)
Turn the rear seat warmer switch off.
Refer to Seat Warmer on page 2-14.
2. If the centre head restraint is in the position for use, store it.
3. Pull the strap on the back of the
seatback to fold the seatback forward.
To return the seatbacks to the upright
position
WA R N I N G
Always make sure the seat belts are fully
pulled out from under the seatbacks:
A seat belt caught under a seatback after
the seatback is returned to its upright
position is dangerous. In a collision or
sudden stop, the seat belt cannot provide
adequate protection.
When returning the seatback to its upright
position, make sure that it is firmly locked
and the red indication is not visible:
If the red indication is visible, the seatback
is not locked. If the vehicle is driven without
the seatback locked, it could fold down
suddenly and cause an accident.
Locked
position
Unlocked
position
Red indicator
Essential Safety Equipment
Seats
2-12
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Positioning the Shoulder Portion of the Seat Belt:
Improper positioning of the shoulder portion of the seat belt is dangerous. Always make sure
the shoulder portion of the seat belt is positioned across your shoulder and near your neck,
but never under your arm, on yo ur neck, or on your upper arm.
Positioning the Lap Portion of the Seat Belt:
The lap portion of the seat belt worn too high is dangerous. In a collision, this would
concentrate the impact force directly on the abdominal area, causing serious injury. Wear the
lap portion of the belt snugly and as low as possible.

In a rollover crash, an unbelted person is significantly more likely to die than a person wearing
a seat belt.

Instructions for Use of Seat Belt Assemblies:
Seatbelts are designed to bear upon the bony structure of the body, and should be worn low
across the front of the pelvis or the pelvis, ch est and shoulders, as applicable; wearing the lap
section of the belt across the abdominal area must be avoided.
Seatbelts should be adjusted as firmly as possi ble, consistent with comfort, to provide the
protection for which they have been designed. A slack belt will greatly reduce the protection
afforded to the wearer.
Care should be taken to avoi d contamination of the webbing with polishes, oils and
chemicals, and particularly battery acid. Cleani ng may safely be carried out using mild soap
and water. The belt should be replaced if webbing becomes frayed, contaminated or
damaged.
It is essential to replace the entire assembly after it has been worn in a severe impact even if
damage to the assembly is not obvious.
Belts should not be worn with straps twisted.
Each belt assembly must only be used by one occupant; it is dangerous to put a belt around a
child being carried on the occupant's lap.
No modifications or additions should be made by the user which will either prevent the seat
belt adjusting devices from operating to remove slack, or prevent the seat belt assembly from
being adjusted to remove slack.
Essential Safety Equipment
Seat Belt Systems
2-18
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

CAUTION
Belt retraction may become difficult if the belts and rings are soiled, so try to keep them clean.
For more details about cleaning the seat belts, refer to "Seat Belt Maintenance" (page 6-67).

Ring
▼Pregnant Women and Persons wi
th Serious Medical Conditions
Pregnant women should always wear seat belts. Ask your doctor f or specific
recommendations.
The lap belt should be worn SNUGL Y AND AS LOW AS POSSIBLE OVER THE HIPS.
The shoulder belt should be worn across your shoulder properly, but never across the
stomach area.
Persons with serious medical conditions also should wear seat b elts. Check with your doctor
for any special instructions regarding specific medical conditi ons.
▼Emergency Locking Mode
When the seat belt is fastened,
it will always be in the emergency locking mode.
In the emergency locking mode, the belt remains comfortable on the occupant and the
retractor will lock in position during a collision.
If the belt is locked and cannot be pulled out, retract the belt once, and then try pulling it out
slowly. If this fails, pull the belt strongly one time and loos en, then pull it out again slowly.
Essential Safety Equipment
Seat Belt Systems
2-19
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Theft-Deterrent System*
If the theft-deterrent system detects an
inappropriate entry in to the vehicle or the
intrusion sensor detects movement in the
vehicle which could result in the vehicle
(with the intrusion sensor) or its contents
being stolen, the alarm alerts the
surrounding area of an abnormality by
sounding the siren/horn and flashing the
hazard warning lights.

The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Intrusion sensor
*
The intrusion s ensor uses ultrasonic waves
to detect movement inside the vehicle and
to raise an alert of an intrusion into the
vehicle.

The intrusion s ensor detects certain kinds
of movement inside the vehicle, however,
it may also respond to phenomenon
outside the vehicle such as vibrations, loud
noise, wind, and air currents.
CAUTION
In order for the intrusion sensor to operate
appropriately, be aware of the following:
 Do not hang clothing or objects from a
head restraint or a coat hook.
 Return the extension sunvisors to their
original positions.
 Do not blind the intrusion sensor by
covering it or placing objects over it.
 Do not allow the intrusion sensor to get
soiled or wipe it with a liquid.
Do not shock or cause an impact to the
intrusion sensor or the intrusion sensor
bezel.
 Do not install seats that are not Mazda
genuine products.
 To prevent obstruction of intrusion
sensor, do not place objects or cargo
near the intrusion sensor that are higher
than the head restraints.

Intrusion sensor and
intrusion sensor bezel
▼ Operation
Siren/Horn triggering conditions
The siren/horn sounds intermittently and
the hazard warning lights flash for about
30 seconds when the system is triggered
by any one of the following:
•Unlocking a door with the auxiliary key
or an inside door-lock knob.
•Forcing open a door, the bonnet or the
liftgate.
•Opening the bonnet by operating the
bonnet release handle.
•Switching the ignition ON without using
the push button start.
•(With the intr
usion sensor)
The intrusion sensor detects a movement
in the vehicle.
Before Driving
Security System
*Some models.3-49
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Rocking the Vehicle
WA R N I N G
Do not spin the wheels at high speed, and
do not allow anyone to stand behind a
wheel when pushing the vehicle:
When the vehicle is stuck, spinning the
wheels at high speed is dangerous. The
spinning tyre could overheat and explode.
This could cause serious injuries.
CAUTION
Too much rocking may cause engine
overheating, transaxle failure, and tyre
damage.
If you must rock the vehicle to free it from
snow, sand or mud, depress the accelerator
slightly and slowly move the shift lever/
selector lever from 1 (D) to R.
Winter Driving
Carry emergency gear, including tyre
chains, window scraper, flares, a small
shovel, jumper leads, and a small bag of
sand or salt.
Ask an expert repairer, we recommend an
Authorised Mazda Repairer to check the
following:
•Have the proper ratio of antifreeze in the
radiator.
Refer to Engine Coolant on page 6-29.
•Inspect the ba ttery and its leads. Cold
reduces battery capacity.
•Use an engine oil appropriate for the
lowest ambient temperatures that the
vehicle will be driven in (page 6-25).
•Inspect the ignition system for damage
and loose connections.
•Use washer fluid made with
antifreeze―but do not use engine
coolant antifreeze for washer fluid (page
6-32).
NOTE
•Remove snow before driving. Snow left
on the windscreen is dangerous as it
could obstruct vision.
•Do not apply excessive force to a
window scraper when removing ice or
frozen snow on the mirror glass and
windscreen.
•Never use warm or hot water for
removing snow or ice from windows and
mirrors as it could result in the glass
cracking.
Before Driving
Driving Tips
3-56
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Turbocharger Information (SKYACTIV-D 2.2)
CAUTION
After driving at freeway speeds or up a long hi ll, idle the engine at least 30 seconds before
stopping it. Otherwise, the turbocharger could be damaged. However, when i-stop
operates, idling is unnecessary.
 Racing or over-revving the engine, particularly after it's just been started, can damage the
turbocharger.
 To protect the engine from damage, the engine is designed so that it cannot be raced just
after starting it in extremely cold weather.
The turbocharger greatly enhances engine power. Its advanced de sign provides improved
operation and requires minimum maintenance.

To get the most from it, observe the following.
1. Change engine oil and filter according to Scheduled Maintenan ce (page 6-3).
2. Use only recommended engine oil (page 6-25). Extra additives are NOT recommended.
Before Driving
Driving Tips
3-60
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•The distance-to-empty is the
approximate remaining distance the
vehicle can be driven until all the
graduation marks in the fuel gauge
indicating the remaining fuel supply
disappear.
•If there is no past fuel economy
information such as after first
purchasing your vehicle or the
information is deleted when the battery
leads are disconnected, the actual
distance-to empty/range may differ from
the amount indicated.
▼Average Fuel Economy
This mode displays the average fuel
economy by calculating the total fuel
consumption and th
e total travelled
distance since purchasing the vehicle,
re-connecting the battery after
disconnection, or resetting the data.
The average fuel economy is calculated
and displayed every minute.

To clear the data being displayed, press the
INFO switch for more than 1.5 seconds.
After pressing the INFO switch, - - -
L/100 km (- - - mpg) will be displayed for
about 1 minute before the fuel economy is
recalculated and displayed.
▼ Current Fuel Economy
This displays the current fuel economy by
calculating the amount of fuel
consumption and the distance travelled.

▼Maintenance Monitor
The following maintenance period
notifications can be
displayed by turning
the Maintenance Monitor on.
•Scheduled Maintenance
•Tyre Rotation
•Oil Change
For the setting method and indications for
the maintenance monitor, refer to the
Maintenance Monitor.
Refer to Maintenance Monitor on page 6-
17.
The maintenance mo nitor displays the
information when the i gnition is switched
ON.
NOTE
This function is inoperable while the
vehicle is being driven.
Message display
When the remaining time or the distance
approaches 0, a message is displayed each
time the ignition is switched ON.
When Driving
Instrument Cluster and Display
4-36
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

SignalWarning Page
ABS Warning Light*1
Electronic Brake
Force Distribu- tion System
Wa r n i n g 7-43
ABS warning 7-46
Charging System Warning Indication/Warning Light*17-43
Engine Oil Warning Light*17-43
(Red) High Engine Coolant Temperature
Warning Indication/Warning Light
*17-43
Power Steering Malfunction Indication/Malfunction Indicator Light*17-43
Master Warning Indication/Warning Light*17-46
Electric Parking Brake (EPB) Warning Indication/Warning Light*17-46
(Red)
*Brake Pedal Operation Demand Warning Light*1
Flashing
4-84
Buzzer & Flash- ing
7-46
Check Engine Light*17-46
*Automatic Transaxle Warning Indication/Warning Light*17-46
*4WD Warning Indication/Warning Light*17-46
Air Bag/Seat Belt Pretensioner System Warning Light*17-46
*Tyre Pressure Monitoring System Warning Light*1
Flashing
7-46
Turns on 7-53
(Amber/White)
*KEY Warning Indication Amber
7-46
White 7-53
When Driving
Instrument Cluster and Display
*Some models.4-43
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Glow Indicator Light
(SKYACTIV-D 2.2)
When the ignition is switched ON, the
glow indicator light turns on. The glow
indicator light turns
off when preheating is
finished.

A problem in the system might be
indicated under the following conditions.
Have your vehicle inspected by an expert
repairer, we recommend an Authorised
Mazda Repairer.
•The glow indicator light does not turn
on when the ignition is switched ON or
it remains on.
•The glow indicator light is flashing.
NOTE
If the vehicle is left with the ignition
switched ON without starting the engine
and a long period of time has elapsed
since preheating finished, the preheating
may be performed again and the glow
indicator light may turn on.
▼ Wrench Indication/Indicator Light
Type A instrument cluster
Perform maintenance in accordance with
the message.
Type B instrument cluster
When the ignition is switched ON, the
wrench indicator ligh
t is illuminated and
then turns off afte r a few seconds.
When illuminated
The wrench indicator light turns on under
the following conditions:
•When the preset maintenance period has
arrived.
•When it’s time to replace the engine oil.
Refer to Maintenance Monitor on page 6-
17.
When flashing (SKYACTIV-D 2.2)
The sedimentor separates water from the
fuel.
If water accumulates in this filter, the
warning light will flash. When it does,
consult an expert repairer, we recommend
an Authorised Mazda Repairer as soon as
possible.
▼ Low Engine Coolant Temperature
Indicator Light (Blue)*
The light illuminates continuously when
the engine coolant temperature is low and
turns off after the engine is warm.

When Driving
Instrument Cluster and Display
4-50*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2