seat adjustment MAZDA MODEL CX-5 2017 Owner's Manual - RHD (UK, Australia) (in English)

(Manual Seat)
When moving the seats forward and rearward or returning a rear-reclined seatback to its
upright position, make sure you hold onto the seatback with your hand while operating. If
the seatback is not held, the seat will move suddenly and could cause injury.
NOTE
•When returning a rear seat to its original position, place the seat belt in its normal
position. Verify that the seat belt pulls out and retracts.
•(Power Seat)
The seat-bottom power adjustment is operated by motors. Avoid extended operation
because excessive use can damage the motors.
•To prevent the battery from running down, avoid using the power adjustment when the
engine is stopped. The adjuster uses a large amount of electrical power.
•Do not use the switch to make more than one adjustment at a time.
Essential Safety Equipment
Seats
2-4
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Front Seat
▼Seat Operation
Power operation
Seat Slide
(Manual Seat)
To move a seat forward or backward, raise the lever and slide t he seat to the desired position
and release the lever.
Make sure the lever returns to i ts original position and the seat is locked in place by
attempting to push it forward and backward.
(Power Seat)
To slide the seat, move the slide lifter switch on the outside of the seat to the front or back
and hold it. Release the sw itch at the desired position.
Height Adjustment*
(Manual Seat)
To adjust the seat height, move the lever up or down.
(Power Seat)
To adjust the seat height, move the switch up or down.
Height Adjustment for Front Edg e of Seat Bottom (Driver's Power Seat)
To adjust the front height of the seat bottom, raise or lower t he front of the slide lifter
switch.
Essential Safety Equipment
Seats
*Some models.2-5
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Seat Recline
(Manual Seat)
To change the seatback angle, lean forward slightly while raisi ng the lever. Then lean back
to the desired position and release the lever.
Make sure the lever returns to i ts original position and the seatback is locked in place by
attempting to push it forward and backward.
(Power Seat)
To change the seatback angle, pr ess the front or rear side of the reclining switch. Release the
switch at the de sired position.
Lumbar Support Adjustment (Driver's Seat)*
(Manual Seat)
To increase the seat firmness, move the lever downward. Move th e lever upward to decrease
firmness.
(Power Seat)
To increase the seat firmness, press and hold the front part of the switch to the desired
position, then release it.
Press the rear part of the switch to decrease firmness.
▼ Seat Warmer*
The front seats are electrically heated. The
ignition must be switched ON.
Press the seat warmer switch while the
ignition is switched ON to operate the seat
warmer. The indicato
r lights turn on to
indicate that the seat warmer is operating.
The mode changes as follows each time
the seat warmer switch is pressed.
OFF
High
Mid
Low
WA R N I N G
Be careful when using the seat warmer:
The heat from the seat warmer may be too
hot for some people, as indicated as
follows, and could cause a
low-temperature burn.
 Infants, small children, elderly people,
and physically challenged people
 People with delicate skin
 People who are excessively fatigued
 People who are intoxicated
 People who have taken sleep-inducing
medicine such as sleeping pills or cold
medicine
Do not use the seat warmer with anything
having high moisture-retention ability such
as a blanket or cushion on the seat:
The seat may be heated excessively and
cause a low-temperature burn.
Essential Safety Equipment
Seats
2-6*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Do not use the seat warmer even when
taking a short nap in the vehicle:
The seat may be heated excessively and
cause a low-temperature burn.
Do not place heavy objects with sharp
projections on the seat, or insert needles or
pins into it:
This could cause the seat to become
excessively heated and result in injury from
a minor burn.
CAUTION
Do not use organic solvents to clean the
seat. It may damage the seat surface and
the heater.
NOTE
•If the ignition is switched off while the
seat warmer is operating (High, Mid or
Low) and then switched ON again, the
seat warmer will automatically operate
at the temperature set before switching
off the ignition.
•Use the seat warmer when the engine is
running. Leaving the seat warmer on for
long periods with the engine not running
could cause the battery power to be
depleted.
•The temperature of the seat warmer
cannot be adjusted beyond High, Mid
and Low because the seat warmer is
controlled by a thermostat.
▼Driving Position Memory*
The desired driving position can be called
up after programming the position.
The following driving positions can be
programmed.
•Driver’s seat position (seat slide, height
adjustment, front edge of seat bottom,
seat recline)
Refer to Seat Operation on page 2-5.
•Active driving display (display position,
brightness level, display information)
Refer to Active Driving Display on page
4-39.
CAUTION
Do not place
fingers or hands around the
bottom of the seat while the seat memory
function is operating. The seat moves
automatically while the seat memory
function is operating and fingers or hands
could get pinched and injured.
SET button
1
2
The driving position can be programmed
or operated using the buttons on the side
of the seat or the key.
NOTE
•Lumbar support adjustment cannot be
programmed.
•Individual seat positions can be
programmed to the two available
programming buttons on the side of the
driver's seat, plus one seat position for
each registered key.
Essential Safety Equipment
Seats
*Some models.2-7
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•If the vehicle has been serviced and the
battery leads disconnected, the
programmed seat positions will have
been erased. Re-programme the seat
positions.
Programming
1. Make sure the parking brake is on.
2. (Automatic transaxle)
Make sure the selector lever is in the P
position.
3. Start the engine.
4. Adjust the seat and the active driving display to the desired driving position.
5. Press the SET button on the seat until a
beep sound is heard one time.
6. Perform one of the following settings within 5 seconds of completing step 5
above:
•Programming using a button on
the side of the seat
Press the butt on you want to
programme, either button 1 or 2,
until a beep sound is heard one time.
•Programming using the key
Press the key
button until a beep
sound is heard one time.
NOTE
If a beep sound is heard three times, the
operation is cancelled.
To move the drivin g position to a
programmed position
(Using a button on the side of the seat)
1. Make sure the parking brake is on.
2.(Automatic transaxle)
Make sure the selector lever is in the P
position.
3. Start the engine.
4. Press the programming button for the driving position you want to call up
(button 1 or 2).
5. A beep sound is heard when the driving position adjustment is
completed.
NOTE
•If the driving position movement is not
changed, only the beep sounds.
•A seat position can be called up even
with the engine not running.
•The driving position adjustment is
cancelled in the following cases:
•Any of the seat adjustment switches is
operated.
•The SET button is pressed.
•Programming button 1 or 2 is pressed.
•The key button or button is
operated.
•The vehicle starts moving.
•The active driving display is adjusted.
(Using a programmed key)
1. Unlock the doors by pressing a request switch or the key
button.
2. After unlocking the doors, the seat position adjustment begins within 40
seconds of opening the driver's door,
and a beep sounds when the operation
is finished.
3. Make sure the parking brake is on.
4. (Automatic transaxle)
Make sure the selector lever is in the P
position.
5. Start the engine.
6. The active driving display adjustment
begins.
Essential Safety Equipment
Seats
2-8
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

NOTE
•If there is no driving position movement,
a beep is not heard.
•The driving position adjustment is
cancelled in the following cases:
•Any of the seat adjustment switches is
operated.
•The SET button is pressed.
•Programming button 1 or 2 is pressed.
•The key button or button is
operated.
•The vehicle starts moving.
•The active driving di splay is adjusted.
Erasing programmed driving positions
(Erasing the driving positions
programmed to the key)
1. Switch the ignition OFF.
2. Press the SET button on the side of the seat until a beep sound is heard one
time.
3. After the beep sounds, press the key
button within 5 seconds until a beep
sound is heard one time.
NOTE
If a beep sound is heard three times, the
operation is cancelled.
Rear Seat
▼ Split Folding
By lowering the rear seatbacks the luggage
compartment space can be expanded.
WA R N I N G
Tightly secure cargo in the luggage
compartment when it is transported with
the seatbacks folded down:
Driving without tightly securing cargo and
luggage is dangerous as it could move and
become an obstruction to driving during
emergency braking or a collision resulting
in an unexpected accident.
CAUTION
If the seatback is not supported by your
hand, it will move suddenly and could
cause injury.
Folding both seatbacks down
CAUTION
Check the position of a front seat before
folding a rear seatback
. Depending on the
position of a front seat, it may not be
possible to fold a rear seatback all the way
down because it may hit the seatback of
the front seat which could scratch or
damage the front seat or its pocket. Lower
or remove the head restraint on the rear
outboard seat if necessary.
Essential Safety Equipment
Seats
2-9
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•When the engine is stopped while the
seat warmers are operating and then the
ignition is switched ON, the seat
warmers will not turn back on
automatically. In addition, the seat
warmer operation stops automatically
after the seat warmers have operated for
about 90 minutes.
To turn the seat warmer back on, press
the switch.
•The temperature of the seat warmer
cannot be adjusted beyond High, Mid
and Low because the seat warmer is
controlled by a thermostat.
▼Armrest*
The rear armrest in the centre of the rear
seatback can be used (no occupant in the
centre seat) or placed upright.

WA R N I N G
Never put your hands and fingers around
the moving parts of the seat and armrest:
Putting your hands and fingers around the
moving parts of the seat and armrest is
dangerous as they could get injured.
Head Restraints
Your vehicle is equipped with head
restraints on all outboard seats and the rear
centre seat. The head restraints are
intended to help protect you and the
passengers from neck injury.
WA R N I N G
Always drive with the head restraints
installed when seats are being used and
make sure they are properly adjusted. In
addition, always raise the head restraints
on the rear outboard seats when they are
being used:
Driving with the head restraints adjusted
too low or removed is dangerous. With no
support behind your head, your neck could
be seriously injured in a collision.
▼Height Adjustment
Adjust the head restra
int so that the centre
is even with the top of the passenger's
ears.

To raise a head restraint, pull it up to the
desired position.
To lower the head restraint, press the
stop-catch release, then push the head
restraint down.
Essential Safety Equipment
Seats
*Some models.2-15
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Front-facing type
WARNING
Never install a front-facing child seat in the
wrong seat position:
Installing a front-facing child seat without
System Suitability for Various Seat
Positions” is dangerous. A front-facing
child seat installed in the wrong seat
position cannot be properly secured. In a
coll ision, the child could hit something or
someone in the vehicle and be seriously
injured or even killed.
Do n ot install a front-facing child-re straint
system on the front pa ssenger seat unless it
is unavoid able:
In a collision, the force of a deploying air
bag could cause serious injury or death to
the child. If installing a front-facing
child-restraint system on the front
passenger seat is unavoidable, move the
front passenger seat as far back as possible
and adjust the seat bottom (height
adjustable seat bottom) to the highest
position at which the seat belt fastening
the child-restraint system is securely
tightened.
Junior Seat Installation Position
A junior sea t is used in the front-facing
pos ition only.
If a junior seat with a removable backr est
is used, usin g the j unior s eat with the
b ack rest ins talled is recommended.

Refer to the table, “Child-Restraint System
Suitabil ity for Various S eat Positions” for
junior seat inst allation pos ition (page 2-
34).
WARNING
Always inst all a junior se at in the co rrect
seat position:
Installing a junior seat without
consulting the table “Child-Restraint
System Suitability for Various Seat
Positions” is dangerous. A junior seat
installed on the wrong seat position cannot
be properly secured. In a collision, the child
could hit something or someone in the
vehicle and be seriously injured or even
killed.
Essential Safety Equipment
Child Restraint
2-32
2017-6-7 7:51:19Form No. CX-5 8FY4-EE-17E+L_Edition2
We recommend the use of the junior seat
with backrest to allow simple adjustment
of the shoulder belt position and to give
your child the best protection.

To return the mirrors to their on-road
positions, press the upper side
of the
outside mirror folding switch.
Fold in Fold out
Automatic folding function*
The automatic folding function operates
when the ignition is switched to ACC or
OFF.
When the outside mirror automatic folding
switch is pressed to the AUTO position
(neutral position),
the outside mirrors
automatically fold in and out when the
doors are locked and unlocked.
Also, when the ignition is switched ON or
the engine is started, the outside mirrors
fold out automatically.
NOTE
The outside mirrors may not fold in and
out automatically under cold weather
conditions.
If the outside mirro rs do not fold in and
out automatically, remove any ice or snow,
and then press the upper or lower side of
the outside mirror automatic folding
switch to fold the outs ide mirrors in or out.
Engine-off outside mirror operation*
The outside mirrors can be operated for
about 40 seconds after the ignition is
switched from ON to off.
▼Rearview Mirror
WA R N I N G
Do not stack cargo or objects higher than
the seatbacks:
Cargo stacked higher than the seatbacks is
dangerous. It can block your view in the
rearview mirror, which might cause you to
hit another car when changing lanes.
Rearview mirror adjustment
Before driving, adjust the rearview mirror
to centre on the scene through the rear
window.

NOTE
For the manual antidazzle mirror, perform
the adjustment with the antidazzle lever in
the day position.
Before Driving
Mirrors
3-38*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Index
Engine Coolant Temperature
Gauge........................................... 4-33
Fuel gauge................................... 4-34
Lane-keep Assist System (LAS) &
Lane Departure Warning System
(LDWS) Display..........................4-38
Maintenance monitor...................4-36
Mazda Radar Cruise Control with
Stop & Go function (MRCC with
Stop & Go function) System
Display......................................... 4-37
Mazda Radar Cruise Control
(MRCC) display.......................... 4-37
Odometer and trip meter............. 4-33
Outside temperatur e display........ 4-35
Vehicle Speed Alarm................... 4-38
Warning (Display Indication)...... 4-38
O
Odometer and Trip Meter................. 4-24
Outside Mirrors................................. 3-36
Outside Temperature Display............4-27
Outside temperature warning beep....7-65
Overhead Console........................... 5-148
Overhead Light............................... 5-142
Overhead Lights......... ..................... 5-142
Overheating....................................... 7-37
Owner Maintenance Closing the bonnet.......................6-23
Engine compartment overview.... 6-24
Key battery replacement..............6-41
Opening the bonnet..................... 6-22
Owner maintenance
precautions................................... 6-20
P
Parking Brake....................................4-81
Parking Sensor System................... 4-229
Park assist sensor system
operation.................................... 4-231
Sensor detection range.............. 4-231
Personalisation Features.................... 9-12
Power Liftgate................................... 3-21
Power Liftgate Warning Beep........... 7-65
Power Steering................................ 4-104
Power Steering Warning Buzzer....... 7-66
Power Windows................................ 3-40
R
Radar Sensors (Rear)...................... 4-204
Radar Sensor (Front).......................4-201
Rearview Mirror................................3-38
Rear Coat Hooks......... .................... 5-152
Rear Cross Traffic Alert (RCTA).... 4-133
Rear Door Child Safet y Locks.......... 3-18
Rear Fog Light.................................. 4-69
Rear Seat............................................. 2-9
Rear View Monitor......................... 4-217 Displayable range on the
screen......................................... 4-219
Picture quality adjustment......... 4-228
Rear view monitor operation..... 4-221
Rear view parking camera
location...................................... 4-218
Switching to the rear view monitor
display........................................4-218
Variance between actual road
conditions and displayed
image......................................... 4-226
Viewing the display................... 4-220
Rear window Rear Window Defogge r...............4-76
Rear Window Defogger.................... 4-76
Rear Window Washer... .................... 4-75
Rear Window Wiper......................... 4-75
Recommended Oil.............................6-25
Recording of Vehicle Data.................. 8-5
Registering Your Vehicle in A Foreign
Country................................................ 8-2
Replacement
10-8
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2