wheel size MAZDA MODEL CX-5 2017 Owner's Manual - RHD (UK, Australia) (in English)

•Drive slowly. Braking performance can
be adversely affected if snow or ice
adheres to the brake components. If this
situation occurs, drive the vehicle
slowly, releasing the accelerator pedal
and lightly applying the brakes several
times until the brake performance
returns to normal.
▼Snow Tyres
WA R N I N G
Use only the same size and type tyres
(snow, radial, or non-radial) on all four
wheels:
Using tyres different in size or type is
dangerous. Your vehi
cle's handling could
be greatly affected and result in an
accident.
CAUTION
Check local regulations before using
studded tyres.
Use snow tyres on all four wheels
Do not exceed the maximum permissible
speed for your snow tyres or legal speed
limits.
Europe
When snow tyres are used, select the
specified size and pressure (page 9-9).
▼ Ty r e C h a i n s
Check local regulations before using tyre
chains.
CAUTION

Chains may
affect handling.
 Do not go faster than 50 km/h (30 mph)
or the chain manufacturer's
recommended limit, whichever is lower.
 Drive carefully and avoid bumps, holes,
and sharp turns.
 Avoid locked-wheel braking.
 Do not use chains on a temporary spare
tyre; it may result in damage to the
vehicle and to the tyre.
In some models, the vehicle is not
equipped with a factory installed
temporary spare tyre.
 Do not use chains on roads that are free
of snow or ice. The tyres and chains could
be damaged.
 Chains may scratch or chip aluminium
wheels.
NOTE
If your vehicle is equipped with the tyre
pressure monitoring system, the system
may not function correctly when using tyre
chains.
Install the chains on the front tyres only.
Do not use chains on the rear tyres.
Before Driving
Driving Tips
3-57
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Dynamic Stability Control(DSC)
The Dynamic Stability Control (DSC)
automatically controls braking and engine
torque in conjunction with systems such as
ABS and TCS to help control side slip
when driving on slippery surfaces, or
during sudden or evasive manoeuvring,
enhancing vehicle safety.

Refer to ABS (page 4 -90) and TCS (page
4-91).

DSC operation is possible at speeds
greater than 20 km/h (12 mph).

The warning light turns on when the
system has a malfunction.
Refer to Warning Indication/Warning
Lights on page 4-42.
WA R N I N G
Do not rely on the Dynamic Stability
Control as a substitute for safe driving:
The Dynamic Stability Control (DSC)
cannot compensate for unsafe and reckless
driving, excessive speed, tailgating
(following another vehicle too closely), and
hydroplaning (reduced tyre friction and
road contact because of water on the road
surface). You can still have an accident.
CAUTION
 The DSC may not operate correctly
unless the following are observed:
 Use tyres of the correct size
specified
for your Mazda on all four wheels.
 Use tyres of the same manufacturer,
brand and tread pattern on all four
wheels.
 Do not mix worn tyres.
 The DSC may not operate correctly when
tyre chains are used or a temporary spare
tyre is installed because the tyre diameter
changes.
▼ TCS/DSC Indicator Light
This indicator light stays on for a few
seconds when the ignition is switched ON.
If the TCS or DSC
is operating, the
indicator light flashes.

If the light stays on, the TCS, DSC or the
brake assist system may have a
malfunction and they may not operate
correctly. Take your vehicle to an expert
repairer, we recommend an Authorised
Mazda Repairer.
When Driving
ABS/TCS/DSC
4-93
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

i-ACTIV AWD Operation*
4WD provides excellent drivability on
snow-covered and ice-packed roads, sand
and mud, as well as on steep slopes and
other slippery surfaces.
A system malfunction or operation
conditions are indicated by a warning.
Refer to Warning Indication/Warning
Lights on page 4-42.
WA R N I N G
Never spin a wheel that is off the ground:
Spinning a wheel that is off the ground as a
result of the vehicle being stuck or in a
ditch is dangerous. The drive assembly
could be seriously damaged which could
lead to an accident or could even lead to
overheating, oil leakage, and a fire.
▼ 4WD Driving
This vehicle has not been designed for the
purpose of off-road driving or rallies. Do
not attempt to drive over uneven or rocky
surfaces, or across rivers.
Although this vehicle is equipped with
4WD, acceleration, steering and braking
operations should be conducted in the
same manner as with a non-4WD vehicle,
with the emphasis placed on safe driving.
▼Tyres and Tyre Chains
The condition of the tyres plays a large
role in the performance of the vehicle.
Moreover, to prevent adverse effects to the
drive assembly, please note the following:
Ty r e s
•When replacing tyres, always replace all
front and rear tyres
at the same time.
•All tyres must be of the same size,
manufacture, brand and tread pattern.
Pay particular attention when equipping
snow or other types of winter tyres.
•Do not mix tread-worn tyres with
normal tyres.
•Inspect tyre inflation pressures at the
specified periods adjust to the specified
pressures.
NOTE
Check the tyre inflation pressure label
attached to driver's door frame for the
correct tyre inflation pressure.
•Make sure to equip the vehicle with
genuine wheels of the specified size, on
all wheels. With 4WD, the system is
calibrated for all four wheels being of
the same dimensions.
Ty r e c h a i n s
•Install tyre chains to the front tyres.
•Do not use tyre chains on the rear
wheels.
•Do not drive the vehicle faster than 30
km/h (19 mph) with the tyre chains
installed.
•Do not drive the vehicle with tyre chains
on road conditions other than snow or
ice.
▼ To w i n g
If the vehicle requires towing, have it
towed with all four wheels completely off
the ground.
Refer to Towing Description on page 7-
39.
When Driving
i-ACTIV AWD
*Some models.4-103
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

WA R N I N G
Do not rely completely on the LAS&LDWS:
The LAS&LDWS is not an automatic driving system. In addition, the system is not designed
to compensate for a driver's lack of caution, and over-reliance on the system could lead to
an accident.
 The detection ability of the LAS&LDWS is limite d. Always stay on course using the steering
wheel and drive with care.
Do not use the LAS&LDWS in the following cases:
The system may not operate adequately accordin g to the actual driving conditions, resulting
in an accident.
 Driving on roads with tight curves.
 Driving under bad weather conditions (rain, fog, and snow).
 Slippery roads such as ice or snow-bound roads.
 Roads with heavy traffic and insufficient distance between vehicles.
 Roads with no white (yellow) lane lines.
 Narrow roads resulting from road construction or lane closures.
 The vehicle is driven on a temp orary lane or section with a closed lane resulting from road
construction where there may be multiple white (yellow) lane lines or they are interrupted.
 Vehicle is driven on roads other than expressways and highways.
 The tyre pressures are not adjusted to the specified pressure.
 Tyres of a different specified size are used, such as an emergency spare tyre.
CAUTION
Heed the following cautions so that the LAS&LDWS can operate normally.
Do not modify the suspensions.
 Always use wheels of the specified type and size for the front and rear wheels. Consult an
expert repairer, we recommend an Authoris ed Mazda Repairer for tyre replacement.
NOTE
•When the direction indicator lever is operated for a lane change, the LAS&LDWS is
automatically disabled. The LAS&LDWS beco mes operational again when the direction
indicator lever is returned and the system detects white (yellow) lane lines while the
vehicle is being driven normally within its vehicle lane.
When Driving
i-ACTIVSENSE
4-164
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Do not apply a strong force to an ultrasonic sensor (rear):
When washing the vehicle, do not spray highly pressurised water against an ultrasonic sensor
(rear), or rub it strongly. In addition, do not hit the rear bumper forcefully when loading and
unloading cargo Otherwise, the sensors may no t detect obstructions correctly which could
cause the SCBS R system to not operate no rmally, or it could operate unnecessarily.
CAUTION
When driving
off-road in areas where there is grass or foliage, it is recommended that the
SCBS R system be turned off.
 Always use tyres of the specified size and th e same manufacturer, brand, and tread pattern
on all 4 wheels. In addition, do not use tyres wi th significantly different wear patterns on the
same vehicle. Otherwise, the SCBS R system may not operate normally.
 If ice or snow is stuck on the ultrasonic sensors (rear) they may not be able to detect
obstructions correctly depending on the conditions. In such cases, the system may not be
able to perform controls correctly. Always dr ive carefully and pay attention to the rear of
the vehicle.
NOTE
•The vehicle posture changes depending on the accelerator pedal, brake pedal and
steering wheel operations, which could make it difficult for the system to recognise an
obstruction, or it could facilitate unnecessary detection. In such cases, the SCBS R may or
may not operate.
•The SCBS R system will operate under the following conditions.
•The engine is running.
•The change lever (manual transaxle vehicle) or the selector lever (automatic transaxle
vehicle) is in the R (reverse) position.
•“Reverse Smart City Brake Support Malfunction” is not displayed in the
multi-information display.
•The vehicle speed is between about 2 to 8 km/h (2 to 4 mph).
•The SCBS R is not turned off.
•The DSC is not malfunctioning.
•The SCBS R operates using ultrasonic sensors (rear) which detect obstructions at the rear
by emitting ultrasonic waves and then receiving the returning waves reflected off the
obstructions.
•In the following cases, the ultrasonic sensors (rear) cannot detect obstructions and the
SCBS R may not operate.
•The height of the obstruction is low such as low walls or trucks with low loading
platforms.
When Driving
i-ACTIVSENSE
4-190
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Smart Brake Support (SBS)
 The direction in which the Forward Sensing Camera (FSC) is pointed has been finely
adjusted. Do not change the installation posi tion of the Forward Sensing Camera (FSC) or
remove it. Otherwise, it could result in damage or malfunction.
 Always use tyres for all wheels that are of the
specified size, and the same manufacturer,
brand, and tread pattern. In addition, do no t use tyres with significantly different wear
patterns on the same vehicle as the system may not operate normally.
 The Forward Sensing Camera (FSC) includes a function for detecting a soiled windscreen
and informing the driver, however, depending on the conditions, it may not detect plastic
shopping bags, ice or snow on the windscreen . In such cases, the system cannot accurately
determine a vehicle ahead and may not be able to operate normally. Always drive carefully
and pay attention to the road ahead.
NOTE
•In the following cases, the Forward Sensing Camera (FSC) cannot detect target objects
correctly, and each system may be unable to operate normally.
•The height of the vehicle ahead is low.
•You drive your vehicle at the same speed as the vehicle ahead.
•Headlights are not turned on during the night or when going through a tunnel.
•In the following cases, the Forward Sensing Camera (FSC) may not be able to detect
target objects correctly.
•Under bad weather condition, such as rain, fog and snow.
•The window washer is being used or the windscreen wipers are not used when it's
raining.
•Ice, fog, snow, frost, rainfall, dirt, or foreign matter such as a plastic bag is stuck on the
windscreen.
•Trucks with low loading plat forms and vehicles with an extremely low or high profile.
•When driving next to walls with no patterning (including fences and longitudinally
striped walls).
•The tail lights of the vehicle ahead are turned off.
•A vehicle is outside the illumi nation range of the headlights.
•The vehicle is making a sharp turn, or ascending or descending a steep slope.
•Entering or exiting a tunnel.
•Heavy luggage is loaded causing the vehicle to tilt.
•Strong light is shone at the front of the vehicle (back light or high-beam light from
on-coming vehicles).
•There are many light emitters on the vehicle ahead.
•When the vehicle ahead is not equipped with tail lights or the tail lights are turned off at
nighttime.
When Driving
i-ACTIVSENSE
4-198
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Do not use the front bumper to push other vehi cles or obstructions such as when pulling
out of a parking space. Otherwise, the radar sensor (front) could be hit and its position
deviated.
 Do not remove, disassemble, or modify the radar sensor (front).
 For repairs, replacement or paint work around the radar sensor (front), consult an
Authorised Mazda Repairer.
 Do not modify the suspension. If the suspensi on are modified, the vehicle's posture could
change and the radar sensor (front) may not be able to correctly detect a vehicle ahead or
an obstruction.
NOTE
•Under the following conditions, the
radar sensor (front) may not be able to
detect vehicles ahead or obstructions
correctly and each system may not
operate normally.
•The rear surface of a vehicle ahead
does not reflect radio waves
effectively, such as an unloaded
trailer or an automobile with a
loading platform covered by a soft
top, vehicles with a hard plastic
tailgate, and round-shaped vehicles.
•Vehicles ahead with low vehicle
height and thus less area for
reflecting radio waves.
•Visibility is reduced due to a vehicle
ahead casting off water, snow, or
sand from its tyres and onto your
windscreen.
•The luggage compartment is loaded
with heavy objects or the rear
passenger seats are occupied.
•Ice, snow, or soiling is on the front
surface of the front emblem.
•During inclement weather such as
rain, snow, or sand storms.
•When driving near facilities or
objects emitting strong radio waves.
•Under the following conditions, the
radar sensor (front) may not be able to
detect vehicles ahead or obstructions.
•The beginning and end of a curve.
•Roads with continuous curves.
•Narrow lane roads due to road
construction or lane closures.
•The vehicle ahead enters the radar
sensor's blind spot.
•The vehicle ahead is running
abnormally due to accident or
vehicle damage.
•Roads with repeated up and down
slopes
•Driving on poor roads or unpaved
roads.
•The distance between your vehicle
and the vehicle ahead is extremely
short.
•A vehicle suddenly comes close such
as by cutting into the lane.
•To prevent incorrect operation of the
system, use tyres of the same specified
size, manufacturer, brand, and tread
pattern on all four wheels. In addition,
do not use tyres with significantly
different wear patterns or tyre
pressures on the same vehicle
(Including the temporary spare tyre).
•If the battery power is weak, the system
may not operate correctly.
When Driving
i-ACTIVSENSE
4-202
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Tyre Pressure Monitoring System*
The Tyre Pressure Monitoring System (TPMS) monitors the pressure for each tyre.
If tyre pressure is too low in one or more tyres, the system wi ll inform the driver via the
warning light in the instrument cluster and by the warning beep sound.
Refer to Warning Indication/Warning Lights on page 4-42.
Refer to Tyre Inflation Pressu re Warning Beep on page 7-66.

The tyre pressure sensors installed on each wheel send tyre pressure data by radio signal to
the receiver unit in the vehicle.
Tyre pressure sensors
NOTE
When the ambient temperature is low due to seasonal changes, tyre temperatures are also
lower. When the tyre temperature decreases, the air pressure decreases as well. The TPMS
warning light may illumina te more frequently. Visually inspect the tyres daily before driving,
and check tyre pressures monthly with a tyre pressure gauge. When checking tyre pressures,
use of a digital tyre pressure gauge is recommended.

TPMS does not alleviate your need to check the pressure and con dition of all four tyres
regularly.
CAUTION
 Each tyre, including the spare (if provided), should be checked monthly when cold and
inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle
placard or tyre inflation pressure label. (If your vehicle has tyres of a different size than the
size indicated on the vehicle placard or tyre inflation pressure label, you should determine
the proper tyre inflation pressure for those tyres.)
When Driving
Tyre Pressure Monitoring System
4-212*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

6. Insert a new battery with the positivepole facing up, and then cover the
battery with the battery cap.
7. Close the cover.
8. Reinsert the auxiliary key.
Ty r e s
For reasons of proper performance, safety,
and better fuel economy, always maintain
recommended tyre inflation pressures and
stay within the recommended load limits
and weight distribution.
WA R N I N G
Using Different Tyre Types:
Driving your vehicle with different types of
tyres is dangerous. It could cause poor
handling and poor braking; leading to loss
of control.
Except for the limited use of the temporary
spare tyre, use only the same type tyres
(radial, bias-belted, bias-type) on all four
wheels.
Using Wrong-Sized Tyres:
Using any other tyre size than what is
specified for the vehicle (page 9-9) is
dangerous. It could seriously affect ride,
handling, ground clearance, tyre clearance,
and speedometer calibration. This could
cause you to have an accident. Use only
tyres that are the correct size specified for
the vehicle.
▼ Tyre Inflation Pressure
WA R N I N G
Always
inflate the tyres to the correct
pressure:
Overinflation or underinflation of tyres is
dangerous. Adverse handling or
unexpected tyre failure could result in a
serious accident.
Refer to Tyres on page 9-9.
Maintenance and Care
Owner Maintenance
6-43
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

The temporary spare tyre has a tread life
of less than 5,000 km (3,000 miles). The
tread life may be shorter depending on
driving conditions.
 The temporary spare tyre is for limited
use, however, if the tread wear
solid-band indicator appears, replace the
tyre with the same type of temporary
spare (page 6-45).
▼ Replacing a Wheel
WA R N I N G
Always use wheels of the correct size on
your vehicle:
Using a wrong-sized wheel is dangerous.
Braking and handling could be
affected,
leading to loss of control and an accident.
CAUTION
A wrong-sized wheel may adversely affect:
 Tyre fit
 Wheel and bearing life
 Ground clearance
 Snow-chain clearance
 Speedometer calibration
 Headlight aim
 Bumper height
 Tyre Pressure Monitoring System
*
NOTE
•When replacing a wheel, make sure the
new one is the same as the original
factory wheel in diameter, rim width,
and offset (inset/outset).
•For details, contact an expert repairer,
we recommend an Authorised Mazda
Repairer.

Proper tyre balancing provides the best
riding comfort and helps reduce tread
wear. Out-of-balance tyres can cause
vibration and uneven wear, such as
cupping and flat spots.
Maintenance and Care
Owner Maintenance
6-46*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2