battery MAZDA MODEL CX-5 2017 Owners Manual (in English)
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2017, Model line: MODEL CX-5, Model: MAZDA MODEL CX-5 2017Pages: 664, PDF Size: 11.73 MB
Page 18 of 664
2–4
Essential Safety Equipment
Seats
NOTE
When returning a rear seat to its original position, place the seat belt in its normal
position. Verify that the seat belt pulls out and retracts.
(Power Seat) The seat-bottom power adjustment is operated by motors. Avoid extended operation
because excessive use can damage the motors.
To prevent the battery from running down, avoid using the power adjustment when the
engine is stopped. The adjuster uses a large amount of electrical power.
Do not use the switch to make more than one adjustment at a time.
CX-5_8FN1-EA-16L_Edition1.indb 42016/12/12 10:05:15
Page 22 of 664
2–8
Essential Safety Equipment
Seats
*Some models.
CAUTION
Do not use organic solvents to clean
the seat. It may damage the seat
surface and the heater.
NOTE
If the ignition is switched off while the
seat warmer is operating (High, Mid or
Low) and then switched ON again, the
seat warmer will automatically operate
at the temperature set before switching
off the ignition.
Use the seat warmer when the engine
is running. Leaving the seat warmer
on for long periods with the engine not
running could cause the battery power
to be depleted.
The temperature of the seat warmer
cannot be adjusted beyond High, Mid
and Low because the seat warmer is
controlled by a thermostat.
Driving Position Memory *
The desired driving position can be called
up after programming the position.
The following driving positions can be
programmed.
Driver’s seat position (seat slide, height
adjustment, front edge of seat bottom,
seat recline)
Refer to Seat Operation on page 2-5 . Active driving display (display position,
brightness level, display information)
Refer to Active Driving Display on page 4-28 .
CAUTION
Do not place fi ngers or hands around
the bottom of the seat while the seat
memory function is operating. The
seat moves automatically while the
seat memory function is operating and
fi ngers or hands could get pinched and
injured.
SET button
1
2
The driving position can be programmed
or operated using the buttons on the side
of the seat or the key.
NOTE
Lumbar support adjustment cannot be
programmed.
Individual seat positions can be
programmed to the two available
programming buttons on the side of the
driver's seat, plus one seat position for
each registered key.
If the vehicle has been serviced and
the battery cables disconnected, the
programmed seat positions will have
been erased. Re-program the seat
positions.
CX-5_8FN1-EA-16L_Edition1.indb 82016/12/12 10:05:15
Page 30 of 664
2–16
Essential Safety Equipment
Seats
WARNING
Be careful when using the seat warmer: The heat from the seat warmer may be
too hot for some people, as indicated
as follows, and could cause a low-
temperature burn.
Infants, small children, elderly people, and physically challenged
people
People with delicate skin People who are excessively fatigued People who are intoxicated People who have taken sleep-inducing medicine such as sleeping
pills or cold medicine
Do not use the seat warmer with
anything having high moisture-
retention ability such as a blanket or
cushion on the seat: The seat may be heated excessively
and cause a low-temperature burn.
Do not use the seat warmer even when
taking a short nap in the vehicle: The seat may be heated excessively
and cause a low-temperature burn.
Do not place heavy objects with sharp
projections on the seat, or insert
needles or pins into it: This could cause the seat to become
excessively heated and result in injury
from a minor burn.
CAUTION
Before folding a rear seatback, make sure that the rear seat warmer switch is
off . If a rear seatback is folded while the
rear seat warmer is in operation, it may
heat the seat excessively and damage
the seat surface.
Do not use organic solvents to clean the seat. It may damage the seat surface
and the heater.
NOTE
Use the seat warmer when the engine
is running. Leaving the seat warmer
on for long periods with the engine not
running could cause the battery power
to be depleted.
When the engine is stopped while
the seat warmers are operating and
then the ignition is switched ON, the
seat warmers will not turn back on
automatically. In addition, the seat
warmer operation stops automatically
after the seat warmers have operated
for about 90 minutes.
To turn the seat warmer back on, press the switch.
The temperature of the seat warmer
cannot be adjusted beyond High, Mid
and Low because the seat warmer is
controlled by a thermostat.
CX-5_8FN1-EA-16L_Edition1.indb 162016/12/12 10:05:17
Page 82 of 664
3–2
Before Driving
Keys
Keys
WARNING
Do not leave the key in your vehicle with
children and keep them in a place where
your children will not fi nd or play with
them: Leaving children in a vehicle with the
key is dangerous. This could result in
someone being badly injured or even
killed. Children may fi nd these keys to
be an interesting toy to play with and
could cause the power windows or
other controls to operate, or even make
the vehicle move.
CAUTION
Because the key (transmitter) uses low-intensity radio waves, it may not
function correctly under the following
conditions:
The key is carried with communication devices such as
cellular phones.
The key contacts or is covered by a metal object.
The key is near electronic devices such as personal computers.
Non-Mazda genuine electronic equipment is installed in the vehicle.
There is equipment which discharges radio waves near the vehicle.
The key (transmitter) may consume battery power excessively if it receives
high-intensity radio waves. Do not place
the key near electronic devices such as
televisions or personal computers.
To avoid damage to the key (transmitter), DO NOT:
Drop the key. Get the key wet. Disassemble the key. Expose the key to high temperatures on places such as the dashboard or
hood, under direct sunlight.
Expose the key to any kind of magnetic fi eld.
Place heavy objects on the key. Put the key in an ultrasonic cleaner. Put any magnetized objects close to the key.
CX-5_8FN1-EA-16L_Edition1.indb 22016/12/12 10:05:28
Page 84 of 664
3–4
Before Driving
Keys
CAUTION
Radio equipment like this is governed
by laws in the United States.
Changes or modifi cations not expressly
approved by the party responsible
for compliance could void the user's
authority to operate the equipment.
NOTE
The keyless entry system operation may
vary due to local conditions.
The keyless entry system is fully
operational (door/liftgate lock/unlock)
when the ignition is switched off. The
system does not operate if the ignition is
switched to any position other than off.
If the key does not operate when
pressing a button or the operational
range becomes too small, the battery
may be weak. To install a new battery,
refer to Key Battery Replacement (page
6-36 ).
Battery life is about one year. Replace
the battery with a new one if the KEY
indicator light (green) fl ashes in the
instrument cluster (for vehicles with
a type A instrument cluster (page
4-32 ), messages are displayed in
the instrument cluster). Replacing
the battery about once a year is
recommended because the KEY warning
light/indicator light may not illuminate
or fl ash depending on the rate of battery
depletion.
Additional keys can be obtained at
an Authorized Mazda Dealer. Up to
6 keys can be used with the keyless
functions per vehicle. Bring all keys
to an Authorized Mazda Dealer when
additional keys are required.
CX-5_8FN1-EA-16L_Edition1.indb 42016/12/12 10:05:28
Page 90 of 664
3–10
Before Driving
Advanced Keyless Entry System
*Some models.
Advanced Keyless Entry
System
*
WARNING
Radio waves from the key may aff ect
medical devices such as pacemakers: Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will aff ect
the device.
The advanced keyless function allows you
to lock/unlock the door and the liftgate, or
open the liftgate while carrying the key.
System malfunctions or warnings are
indicated by the following warning beeps.
Request switch Inoperable Warning
Beep
Refer to Request Switch Inoperable Warning Beep (With the advanced
keyless function) on page 7-41 .
Key Left-in-luggage Compartment
Warning Beep
Refer to Key Left-in-luggage Compartment Warning Beep (With the
advanced keyless function) on page
7-41 .
Key Left-in-vehicle Warning Beep Refer to Key Left-in-vehicle Warning
Beep (With the advanced keyless
function) on page 7-41 .
NOTE
The advanced keyless entry system
functions can be deactivated to prevent
any possible adverse effect on a user
wearing a pacemaker or other medical
device. If the system is deactivated, you
will be unable to start the engine by
carrying the key. Consult an Authorized
Mazda Dealer for details. If the advanced
keyless entry system has been deactivated,
you can start the engine by following the
procedure indicated when the key battery
goes dead.
Refer to Engine Start Function When Key
Battery is Dead on page 4-8 .
CX-5_8FN1-EA-16L_Edition1.indb 102016/12/12 10:05:29
Page 91 of 664
3–11
Before Driving
Advanced Keyless Entry System
Operational Range
The system operates only when the driver
is in the vehicle or within operational
range while the key is being carried.
NOTE
When the battery power is low, or in
places where there are high-intensity radio
waves or noise, the operational range
may become narrower or the system may
not operate. For determining battery
replacement, Refer to Keyless Entry
System on page 3-3 .
Locking, Unlocking the Doors and the Liftgate
Exterior antenna
Operational range 80cm (31in)
80cm (31in)
80cm (31in)Lock
Exterior antenna
Operational range
80cm (31in)
80cm (31in)Unlock
NOTE
The system may not operate if you
are too close to the windows or door
handles, or liftgate.
If the key is left in the following areas
and you leave the vehicle, the doors
may be locked depending on the radio
wave conditions even if the key is left in
the vehicle.
Around the dashboard In the storage compartments such as
the glove compartment or the center
console
Next to a communication device such
as a mobile phone
Opening the Liftgate
Exterior antenna
80cm (31in)
Operational range
CX-5_8FN1-EA-16L_Edition1.indb 112016/12/12 10:05:30
Page 93 of 664
3–13
Before Driving
Doors and Locks
NOTE
Always stop the engine and lock the
doors. In addition, to prevent theft of
valuables, do not leave them inside the
cabin.
If the key is left in the following areas
and you leave the vehicle, the doors
may be locked depending on the radio
wave conditions even if the key is left in
the vehicle.
Around the dashboard In the storage compartments such as
the glove compartment or the center
console
Next to a communication device such
as a mobile phone
When the ignition is switched to ACC
or ON, the vehicle lock-out prevention
feature prevents you from locking
yourself out of the vehicle.
All doors and the liftgate will automatically unlock if they are locked
using the power door locks with any
door or the liftgate open.
The vehicle lock-out prevention feature does not operate while the ignition is
switched off.
When any door is opened from the outside while the key is inside the
vehicle, the closed doors are locked. All
the doors are automatically unlocked by
closing the open door.
(With the advanced keyless function) The beep sound is heard for about
10 seconds to notify the driver that the
key has been left in the vehicle.
(Without the advanced keyless
function)
The horn sound is heard twice to notify
the driver that the key has been left in
the vehicle.
(Door unlock (control) system with
collision detection)
This system automatically unlocks
the doors and the liftgate in the event
the vehicle is involved in an accident
to allow passengers to get out of the
vehicle immediately and prevent being
trapped inside. While the ignition
is switched ON and in the event the
vehicle receives an impact strong
enough to infl ate the air bags, all the
doors and the liftgate are automatically
unlocked after about 6 seconds have
elapsed from the time of the accident.
The doors and the liftgate may not unlock depending on how an impact
is applied, the force of the impact, and
other conditions of the accident.
If door-related systems or the battery is malfunctioning, the doors and the
liftgate will not unlock.
CX-5_8FN1-EA-16L_Edition1.indb 132016/12/12 10:05:30
Page 103 of 664
3–23
Before Driving
Doors and Locks
Opening and Closing the Liftgate
Opening the liftgate with Electric
liftgate opener
Unlock the doors and liftgate, then press
the electric liftgate opener on the liftgate
and raise the liftgate when the latch
releases.
For the power liftgate operation, refer to
Power Liftgate on page 3-24 .
Electric liftgate
opener
NOTE
(With the advanced keyless function) A locked liftgate can also be opened
while the key is being carried.
When opening the liftgate with the
doors and the liftgate locked, it may
require a few seconds for the liftgate
latch to release after the electric liftgate
opener is pressed.
The liftgate can be closed when the
doors are locked with the key left in the
vehicle. However, to prevent locking the
key in the vehicle, the liftgate can be
opened by pressing the electric liftgate
opener. If the liftgate cannot be opened
despite doing this procedure, fi rst push
the liftgate completely closed, then press
the electric liftgate opener to fully open
the liftgate .
When the liftgate latch is released by
pressing the electric liftgate opener,
the liftgate raises slightly. If the liftgate
is not operated for a certain period of
time, the liftgate cannot be raised.
To open Press the electric liftgate opener again. To close To close the liftgate from its slightly
raised position, open it fi rst by pressing
the electric liftgate opener, then close it
after waiting at least 1 second.
If the liftgate is not fully closed, the
driver is noti fi ed by a warning indicated
in the instrument cluster.
If the vehicle battery is dead or there is
a malfunction in the electrical system
and the liftgate cannot be unlocked, the
liftgate can be opened by performing
the emergency procedure.
Refer to When Liftgate Cannot be Opened on page 7-44 .
CX-5_8FN1-EA-16L_Edition1.indb 232016/12/12 10:05:32
Page 105 of 664
3–25
Before Driving
Doors and Locks
CAUTION
When closing the power liftgate, make sure there are no foreign objects
around the striker. If foreign objects are
obstructing the striker, the liftgate may
not close properly.
Striker
Do not install accessories to the power liftgate other than specifi ed accessories.
Otherwise, it cannot be opened/closed
automatically and could result in a
malfunction.
Be careful when switching the power liftgate from electrical to manual
operation. The power liftgate may open/
close unexpectedly depending on its
position which could result in injury.
NOTE
Do not apply unnecessary force to
the power liftgate when it is opening/
closing electrically. Unnecessary force
on the liftgate may cause it to reverse
direction of movement automatically.
Also, it could result in a malfunction.
The power liftgate may not open/close
electrically if the vehicle is parked on
an incline, or there is strong wind, or
the liftgate is laden with snow.
If a power liftgate system fuse has
blown, the liftgate cannot be opened
using the power liftgate switch or
the electric liftgate opener. Use the
emergency lever to open the liftgate.
Fully close the power liftgate before
disconnecting the vehicle battery. If
the battery is disconnected with the
liftgate open, it cannot be opened or
closed automatically after the battery is
reconnected. If this happens, fully close
the liftgate manually to restore the auto
full open/close function.
If the system detects weight such as that
caused by a snow-laden liftgate when
it is opened electrically, after the beep
activates three times, the liftgate stops
after reversing.
If the power liftgate is snow-laden,
remove the snow before operating the
liftgate.
CX-5_8FN1-EA-16L_Edition1.indb 252016/12/12 10:05:32