key battery MAZDA MODEL CX-5 2017 Owners Manual (in English)

2–8
Essential Safety Equipment
Seats
*Some models.
CAUTION
Do not use organic solvents to clean
the seat. It may damage the seat
surface and the heater.

NOTE
  If the ignition is switched off while the
seat warmer is operating (High, Mid or
Low) and then switched ON again, the
seat warmer will automatically operate
at the temperature set before switching
off the ignition.
  Use the seat warmer when the engine
is running. Leaving the seat warmer
on for long periods with the engine not
running could cause the battery power
to be depleted.
  The temperature of the seat warmer
cannot be adjusted beyond High, Mid
and Low because the seat warmer is
controlled by a thermostat.

Driving Position Memory *
The desired driving position can be called
up after programming the position.
The following driving positions can be
programmed.
  Driver’s seat position (seat slide, height
adjustment, front edge of seat bottom,
seat recline)
 Refer to Seat Operation on page 2-5 .   Active driving display (display position,
brightness level, display information)
 Refer to Active Driving Display on page 4-28 .

CAUTION
Do not place fi ngers or hands around
the bottom of the seat while the seat
memory function is operating. The
seat moves automatically while the
seat memory function is operating and
fi ngers or hands could get pinched and
injured.


SET button
1
2

The driving position can be programmed
or operated using the buttons on the side
of the seat or the key.
NOTE
   Lumbar support adjustment cannot be
programmed.
  Individual seat positions can be
programmed to the two available
programming buttons on the side of the
driver's seat, plus one seat position for
each registered key.
  If the vehicle has been serviced and
the battery cables disconnected, the
programmed seat positions will have
been erased. Re-program the seat
positions.

CX-5_8FN1-EA-16L_Edition1.indb 82016/12/12 10:05:15

3–2
Before Driving
Keys
Keys
WARNING
Do not leave the key in your vehicle with
children and keep them in a place where
your children will not fi nd or play with
them: Leaving children in a vehicle with the
key is dangerous. This could result in
someone being badly injured or even
killed. Children may fi nd these keys to
be an interesting toy to play with and
could cause the power windows or
other controls to operate, or even make
the vehicle move.

CAUTION
 Because the key (transmitter) uses low-intensity radio waves, it may not
function correctly under the following
conditions:
 The key is carried with communication devices such as
cellular phones.
 The key contacts or is covered by a metal object.
 The key is near electronic devices such as personal computers.
 Non-Mazda genuine electronic equipment is installed in the vehicle.
 There is equipment which discharges radio waves near the vehicle.
 The key (transmitter) may consume battery power excessively if it receives
high-intensity radio waves. Do not place
the key near electronic devices such as
televisions or personal computers.
 To avoid damage to the key (transmitter), DO NOT:
 Drop the key. Get the key wet. Disassemble the key. Expose the key to high temperatures on places such as the dashboard or
hood, under direct sunlight.
 Expose the key to any kind of magnetic fi eld.
 Place heavy objects on the key. Put the key in an ultrasonic cleaner. Put any magnetized objects close to the key.



CX-5_8FN1-EA-16L_Edition1.indb 22016/12/12 10:05:28

3–4
Before Driving
Keys
CAUTION
Radio equipment like this is governed
by laws in the United States.
Changes or modifi cations not expressly
approved by the party responsible
for compliance could void the user's
authority to operate the equipment.

NOTE
  The keyless entry system operation may
vary due to local conditions.
  The keyless entry system is fully
operational (door/liftgate lock/unlock)
when the ignition is switched off. The
system does not operate if the ignition is
switched to any position other than off.
  If the key does not operate when
pressing a button or the operational
range becomes too small, the battery
may be weak. To install a new battery,
refer to Key Battery Replacement (page
6-36 ).
  Battery life is about one year. Replace
the battery with a new one if the KEY
indicator light (green) fl ashes in the
instrument cluster (for vehicles with
a type A instrument cluster (page
4-32 ), messages are displayed in
the instrument cluster). Replacing
the battery about once a year is
recommended because the KEY warning
light/indicator light may not illuminate
or fl ash depending on the rate of battery
depletion.

  Additional keys can be obtained at
an Authorized Mazda Dealer. Up to
6 keys can be used with the keyless
functions per vehicle. Bring all keys
to an Authorized Mazda Dealer when
additional keys are required.

CX-5_8FN1-EA-16L_Edition1.indb 42016/12/12 10:05:28

3–10
Before Driving
Advanced Keyless Entry System
*Some models.
Advanced Keyless Entry
System
*
WARNING
Radio waves from the key may aff ect
medical devices such as pacemakers: Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will aff ect
the device.

The advanced keyless function allows you
to lock/unlock the door and the liftgate, or
open the liftgate while carrying the key.

System malfunctions or warnings are
indicated by the following warning beeps.
   Request switch Inoperable Warning
Beep
 Refer to Request Switch Inoperable Warning Beep (With the advanced
keyless function) on page 7-41 .
  Key Left-in-luggage Compartment
Warning Beep
 Refer to Key Left-in-luggage Compartment Warning Beep (With the
advanced keyless function) on page
7-41 .
  Key Left-in-vehicle Warning Beep Refer to Key Left-in-vehicle Warning
Beep (With the advanced keyless
function) on page 7-41 .

NOTE
The advanced keyless entry system
functions can be deactivated to prevent
any possible adverse effect on a user
wearing a pacemaker or other medical
device. If the system is deactivated, you
will be unable to start the engine by
carrying the key. Consult an Authorized
Mazda Dealer for details. If the advanced
keyless entry system has been deactivated,
you can start the engine by following the
procedure indicated when the key battery
goes dead.
Refer to Engine Start Function When Key
Battery is Dead on page 4-8 .

CX-5_8FN1-EA-16L_Edition1.indb 102016/12/12 10:05:29

3–11
Before Driving
Advanced Keyless Entry System
Operational Range
The system operates only when the driver
is in the vehicle or within operational
range while the key is being carried.
NOTE
When the battery power is low, or in
places where there are high-intensity radio
waves or noise, the operational range
may become narrower or the system may
not operate. For determining battery
replacement, Refer to Keyless Entry
System on page 3-3 .

Locking, Unlocking the Doors and the Liftgate

Exterior antenna
Operational range 80cm (31in)
80cm (31in)
80cm (31in)Lock


Exterior antenna
Operational range
80cm (31in)
80cm (31in)Unlock

NOTE
 
 The system may not operate if you
are too close to the windows or door
handles, or liftgate.
  If the key is left in the following areas
and you leave the vehicle, the doors
may be locked depending on the radio
wave conditions even if the key is left in
the vehicle.
  Around the dashboard  In the storage compartments such as
the glove compartment or the center
console
  Next to a communication device such
as a mobile phone


Opening the Liftgate

Exterior antenna
80cm (31in)
Operational range

CX-5_8FN1-EA-16L_Edition1.indb 112016/12/12 10:05:30

3–13
Before Driving
Doors and Locks
NOTE
  Always stop the engine and lock the
doors. In addition, to prevent theft of
valuables, do not leave them inside the
cabin.
  If the key is left in the following areas
and you leave the vehicle, the doors
may be locked depending on the radio
wave conditions even if the key is left in
the vehicle.
  Around the dashboard  In the storage compartments such as
the glove compartment or the center
console
  Next to a communication device such
as a mobile phone
  When the ignition is switched to ACC
or ON, the vehicle lock-out prevention
feature prevents you from locking
yourself out of the vehicle.
 All doors and the liftgate will automatically unlock if they are locked
using the power door locks with any
door or the liftgate open.
 The vehicle lock-out prevention feature does not operate while the ignition is
switched off.
 When any door is opened from the outside while the key is inside the
vehicle, the closed doors are locked. All
the doors are automatically unlocked by
closing the open door.
 (With the advanced keyless function)  The beep sound is heard for about
10 seconds to notify the driver that the
key has been left in the vehicle.
 (Without the advanced keyless
function)
 The horn sound is heard twice to notify
the driver that the key has been left in
the vehicle.
  (Door unlock (control) system with
collision detection)
 This system automatically unlocks
the doors and the liftgate in the event
the vehicle is involved in an accident
to allow passengers to get out of the
vehicle immediately and prevent being
trapped inside. While the ignition
is switched ON and in the event the
vehicle receives an impact strong
enough to infl ate the air bags, all the
doors and the liftgate are automatically
unlocked after about 6 seconds have
elapsed from the time of the accident.
 The doors and the liftgate may not unlock depending on how an impact
is applied, the force of the impact, and
other conditions of the accident.
 If door-related systems or the battery is malfunctioning, the doors and the
liftgate will not unlock.

CX-5_8FN1-EA-16L_Edition1.indb 132016/12/12 10:05:30

3–23
Before Driving
Doors and Locks
Opening and Closing the Liftgate
Opening the liftgate with Electric
liftgate opener
Unlock the doors and liftgate, then press
the electric liftgate opener on the liftgate
and raise the liftgate when the latch
releases.
For the power liftgate operation, refer to
Power Liftgate on page 3-24 .

Electric liftgate
opener

NOTE
(With the advanced keyless function)   A locked liftgate can also be opened
while the key is being carried.
  When opening the liftgate with the
doors and the liftgate locked, it may
require a few seconds for the liftgate
latch to release after the electric liftgate
opener is pressed.
  The liftgate can be closed when the
doors are locked with the key left in the
vehicle. However, to prevent locking the
key in the vehicle, the liftgate can be
opened by pressing the electric liftgate
opener. If the liftgate cannot be opened
despite doing this procedure, fi rst push
the liftgate completely closed, then press
the electric liftgate opener to fully open
the liftgate .
   When the liftgate latch is released by
pressing the electric liftgate opener,
the liftgate raises slightly. If the liftgate
is not operated for a certain period of
time, the liftgate cannot be raised.
 To open  Press the electric liftgate opener again.  To close  To close the liftgate from its slightly
raised position, open it fi rst by pressing
the electric liftgate opener, then close it
after waiting at least 1 second.
   If the liftgate is not fully closed, the
driver is noti fi ed by a warning indicated
in the instrument cluster.
   If the vehicle battery is dead or there is
a malfunction in the electrical system
and the liftgate cannot be unlocked, the
liftgate can be opened by performing
the emergency procedure.
 Refer to When Liftgate Cannot be Opened on page 7-44 .

CX-5_8FN1-EA-16L_Edition1.indb 232016/12/12 10:05:32

3–47
Before Driving
Security System
*Some models.
Theft-Deterrent System *
If the theft-deterrent system detects an
inappropriate entry into the vehicle,
which could result in the vehicle or its
contents being stolen, the alarm alerts the
surrounding area of an abnormality by
sounding the horn and fl ashing the hazard
warning lights.

The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Operation
System triggering conditions
The horn sounds intermittently and the
hazard warning lights fl ash for about
30 seconds when the system is triggered
by any one of the following:
   Unlocking a door with the key, door
lock switch, or an inside door-lock knob.
   Forcing open a door, the hood or the
liftgate.
   Opening the hood by operating the hood
release handle.
   Switching the ignition ON without using
the push button start.

If the system is triggered again, the lights
and horn will activate until the driver's
door or the liftgate is unlocked with the
transmitter.
(With the advanced keyless function)
The lights and horn can also be
deactivated by pressing the request switch
on a door.
NOTE
   The liftgate does not open while the
theft-deterrent system is operating.
  For vehicles equipped with the power
liftgate, the liftgate can be opened
even while the theft-deterrent system is
operating by pressing the power liftgate
button on the transmitter or the electric
liftgate opener switch while carrying
the key.
  If the battery goes dead while the theft-
deterrent system is armed, the horn will
activate and the hazard warning lights
will fl ash when the battery is charged or
replaced.

How to Arm the System
1. Close the windows and the moonroof *
securely.
2. Switch the ignition OFF.
3. Make sure the hood, the doors, and the liftgate are closed.
4. Press the lock button on the transmitter or lock the driver's door from the
outside with the auxiliary key.
The hazard warning lights will fl ash
once.
The following method will also arm the theft-deterrent system:
Press the door-lock switch “
” while
any door is open and then close all of
the doors.
(With the advanced keyless function)
Press a request switch.

The security indicator light in the instrument cluster fl ashes twice per
second for 20 seconds.


5. After 20 seconds, the system is fully armed.

CX-5_8FN1-EA-16L_Edition1.indb 472016/12/12 10:05:37

4–4
When Driving
Start/Stop Engine
*Some models.
Ignition Switch
Push Button Start Positions
The system operates only when the key is
within operational range.
Each time the push button start is pressed,
the ignition switches in the order of off,
ACC, and ON. Pressing the push button
start again from ON switches the ignition
off.
Indicator light
Push button start
NOTE
   The engine starts by pressing the push
button start while depressing the brake
pedal. To switch the ignition position,
press the push button start without
depressing the pedal.
  Do not leave the ignition switched ON
while the engine is not running. Doing
so could result in the battery going
dead. If the selector lever is in the P
position, and the ignition is in ACC, the
ignition switches off automatically after
about 25 minutes.

Off
The power supply to electrical devices
turns off and the push button start indicator
light (amber) also turns off.
In this position the steering wheel is
locked.
*
WARNING
Before leaving the driver's seat, always
switch the ignition off , set the parking
brake, and make sure the selector lever
is in P: Leaving the driver's seat without
switching the ignition off , setting the
parking brake, and shifting the selector
lever to P is dangerous. Unexpected
vehicle movement could occur which
could result in an accident.
In addition, if your intention is to leave
the vehicle for even a short period, it
is important to switch the ignition off ,
as leaving it in another position will
disable some of the vehicle's security
systems and run the battery down.

NOTE
(Locked steering wheel) *
If the push button start indicator light
(green) is fl ashing and the beep sound
is heard, this indicates that the steering
wheel is not unlocked. To unlock the
steering wheel, press the push button start
while moving the steering wheel left and
right.

ACC (Accessory)
Some electrical accessories will operate
and the indicator light (amber) illuminates.
In this position the steering wheel is
unlocked.
*
NOTE
The keyless entry system does not function
while the push button start has been
pressed to ACC, and the doors will not
lock/unlock even if they have been locked
manually.

CX-5_8FN1-EA-16L_Edition1.indb 42016/12/12 10:05:40

4–6
When Driving
Start/Stop Engine
NOTE
  The key must be carried because the key
carries an immobilizer chip that must
communicate with the engine controls at
short range.
  The engine can be started when the
push button start is pressed from off,
ACC, or ON.
  The push button start system functions
(function which can start the engine
by only carrying the key) can be
deactivated to prevent any possible
adverse effect on a user wearing a
pacemaker or other medical device. If
the system is deactivated, you will be
unable to start the engine by carrying
the key. Consult an Authorized Mazda
Dealer for details. If the push button
start system functions have been
deactivated, you can start the engine by
following the procedure indicated when
the key battery goes dead.
 Refer to Engine Start Function When Key Battery is Dead on page 4-8 .
  After starting a cold engine, the engine
speed increases and a whining sound
from the engine compartment can be
heard.
 This is for improved exhaust gas purifi cation and does not indicate any
parts defect.
   Engine-starting is controlled by the
spark ignition system.
 This system meets all Canadian Interference-Causing Equipment
Standard requirements regulating the
impulse electrical fi eld strength of radio
noise.

1. Make sure you are carrying the key.
2. Occupants should fasten their seat belts.
3. Make sure the parking brake is on. 4. Continue to press the brake pedal
fi rmly until the engine has completely
started.
5. (Manual transaxle)
Continue to press the clutch pedal fi rmly until the engine has completely
started.
(Automatic transaxle)
Put the vehicle in park (P). If you must restart the engine while the vehicle is
moving, shift into neutral (N).
NOTE
  (Manual transaxle)  The starter will not operate if the clutch
pedal is not depressed suf fi ciently.
   (Automatic transaxle)  The starter will not operate if the
selector lever is not in P or N and the
brake pedal is not depressed suf fi ciently.

6. Verify that the KEY indicator light
(green) (if equipped) in the instrument
cluster and the push button start
indicator light (green) illuminate.



Indicator light
Push button start
CX-5_8FN1-EA-16L_Edition1.indb 62016/12/12 10:05:40