MAZDA MODEL CX-9 2018 (in English) Workshop Manual

Mass groupSize Class Fixture Vehicle LATCH positions
Second-row seat (Outboard)
GROUP 1
9 kg ― 18 kg (20 lb ― 40 lb) DI
SO /R 2 IL
CI SO /R 3 IL
BI SO /F 2 I UF
B1 ISO/F2X IUF
AI SO /F 3 I UF
(1) X
GROUP 2
15 kg ― 25 kg (33 lb ― 55 lb) (1)
X
GROUP 3
22 kg ― 36 kg (48 lb ― 79 lb) (1)
X
(1) For the CRS which do not carry the ISO/XX size class identi fication (A to G), for the applicable mass group, the
car manufacturer shall indicate t he vehicle specific LATCH child-restraint system(s) recommended for each
position.
Key of letters to be inserted in the above table:
IUF = suitable for LATCH forward child-restraints systems of universal category approved for use in this mass
group.
IL = suitable for particular LAT CH child-restraint systems (CRS ).
These LATCH CRS are those of the “specific vehicle”, “restricte d” or “semi-universal” categories.
X = LATCH position not suitable for LATCH child-restraint systems in this mass group and/or this size class.
NOTE
When installing a child-restraint system, the follo wing points must be observed:
•Always remove the head restraint before in stalling a child-restraint system. However,
when installing a backless booster seat, always install the vehicle head restraint to the
seat where the backless booster seat is installed. In addition, always use a tether strap
and attach it securely. Refer to Head Restraints on page 2-18.
•When installing a child-restra int system to the second-row seat, adjust the front seat
position so that the front seat does not contact the child-restraint system. Refer to Seat
Operation on page 2-5.
Essential Safety Equipment
Child Restraint
2-39
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

i-Size child-restraint systems
An i-Size child-restraint system can be installed to the specified seat as follows:
Front passenger seat Rear seat (outboard) Rear seat (center)
i-Size child-restraint sys- tems XXX
Key of letters to be inserted in the above table:
X = Seating position not suitabl
e for i-Size “universal” child-restraint systems.
NOTE
An i-Size child-restraint system refers to a ch ild-restraint system which has acquired i-Size
category certification for the UNECE 129 regulation.
Seat belt-secured child-restraint systems
System group Age
group We i g h t
group Child-r
estraint system
type Front passenger
seat Second-row seat
(outboard) Second-row seat
(center) Third-row seat
(outboard)
GROU P 0 Up to
about 9 months old Up to
10 kg
(up to
22 lb) Infant
seat XU
U
*2U
GROU P 0
Up to
about 2 yearsold Up to
13 kg
(up to
29 lb) Infant
seat XU
U
*2U
GROU P 1 About 8
months to 4
years old 9 kg ―
18 kg
(20 lb
― 40 lb) Child
seat L
*1U
U*2U
GROU P 2 About 3
to 7
years old 15 kg
― 25
kg (33
lb ― 55 lb) Booster
seat L
*1U
U*2U
GROU P 3 About 6
to 12
years old 22 kg
― 36
kg (48
lb ― 79 lb) Booster
seat L
*1U
U*2U
Essential Safety Equipment
Child Restraint
2-40
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

Key of letters to be inserted in the above table:
U = Suitable for “universal” category restraints approved for use in this mass group.
L = For the child restraint systems categorized in this weight group, consult an Authorized Mazda Dealer.
Regarding child restraint systems which can be installed, refer to the accessories catalog.
X = Seat position not suitable for children in this mass group.
*1 A Mazda genuine child restraint system can be installed in the forward-facing position.*2 When a child-restraint system is installed to the rear center seat, do not seat occupants in the rear left outboard
seat position.
NOTE
When installing a ch ild-restraint system, the follo wing points must be observed:
•(Second-row seat)
Always remove the head restraint before in stalling a child-restraint system. However,
when installing a backless booster seat, always install the vehicle head restraint to the
seat where the backless booster seat is installed. In addition, always use a tether strap
and attach it securely. Refer to Head Restraints on page 2-18.
•When installing a child-restra int system to the second-row seat, adjust the front seat
position so that the front seat does not contact the child-restraint system. Refer to Seat
Operation on page 2-5.
•When installing a child-restrain t system to the third-row seat, adjust the second-row seat
position so that the second-row seat does no t contact the child-restraint system. Refer to
Seat Operation on page 2-5.
(Except Mexico)
Please comply with the legal regul ations concerning the use of child-restraint systems in
your country.
Essential Safety Equipment
Child Restraint
2-41
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

Installing Child-RestraintSystems
Accident statistics reveal that a child is
safer in the rear seat . The front passenger's
seat is clearly the worst choice for any
child under 12, and with rear-facing
child-restraint system s it is clearly unsafe
due to air bags.

NOTE
Even if your vehicle is equipped with front
passenger occupant classification sensor
(page 2-73), which automatically
deactivates the front passenger air bag, a
rear seat is the safest place for a child of
any age or size.

Some child-restraint systems now come
with tethers and t herefore must be
installed on the seats that take tethers to be
effective. In your Mazda, tethered
child-restraint systems can only be
accommodated in the four positions on the
rear seat.

Some child-restraint systems also employ
specially designed LATCH attachments;
refer to "Using LA TCH Lower Anchor"
(page 2-52).
WA R N I N G
Tethered Child-Restraint Systems Work
Only on Tether-Equipped Rear Seats:
Installation of a tether equipped
child-restraint system in the front
passenger's seat defeats the safety design
of the system and will result in an increased
chance of serious injury if the
child-restraint system goes forward
without benefit of being tethered.
Place tether equipped child-restraint
systems where there are tether anchors.
▼ Anchor Bracket
Anchor brackets for securing
child-restraint systems are equipped in the
vehicle. Locate each anchor position using
the illustration.
To install a child-restraint system, remove
the head restraint (except third-row seat).
Always follow the
instruction manual
accompanying the child-restraint system.

Essential Safety Equipment
Child Restraint
2-42
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

Anchor bracket location
Use the indicated anchor bracket locations
when installing a child-restraint system
equipped with a tether.
For right
For center
For left
Second-row seat
* *
Except Mexico
Third-row seat
Some models.
WA R N I N G
Always attach the tether strap to the
correct tether anchor position:
Attaching the tether strap to the incorrect
tether anchor position is dangerous. In a
collision, the tether strap could come off
and loosen the child-restraint system. If the
child-restraint system moves it could result
in death or injury to the child.
Always remove the head restraint and
install child-restraint system (Second-row
seat):
Installing a child-restraint system without
removing the head restraint is dangerous.
The child-restraint system cannot be
installed correctly which may result in
death or injury to the child in a collision.
Tether strap
Forward
Second-row
outboard seat
Tether strap
Forward
Second-row
center seat
Always install the head restraint and adjust
it to the appropriate position after
removing the child-restraint system
(Second-row seat):
Driving with the head restraint removed is
dangerous as impact to the occupant's
head cannot be prevented during
emergency braking or in a collision, which
could result in a serious accident, injury or
death.
Refer to Head Restraints on page 2-18.
Essential Safety Equipment
Child Restraint
2-43
CX-9_8GC3-EA-17G_Edition1
2017-5-29 10:13:38

Only use a tether anchor designed for the
second-row seats:
Using a third-row seat tether anchor on the
second-row seat is dangerous. The
child-restraint system cannot be installed
correctly which may result in death or
injury to the child in a collision.
Tether strap
Third-row seatSecond-row
outboard/center
Always route the tether straps to the sides
of the head restraint (Third-row seat):
Routing the tether straps on top of the
head restraint is dangerous. In a collision
the tether straps could slide
off the head
restraint and loosen the child-restraint
system. The child-restraint system could
move which may result in death or injury to
the child.
Tether strap
ForwardThird-row seat
▼Using Automatic Locking Mode*
Follow these instructions when using a
child-restraint system, unless you are
attaching a LATCH-equipped
child-restraint syst
em to the rear LATCH
lower anchors. Refer to “Using LATCH
Lower Anchor” (page 2-52).
NOTE
Follow the child- restraint system
manufacturer's instructions carefully. If
you are not sure whether you have a
LATCH system or tether, check in the
child-restraint system manufacturer's
instructions and follow them accordingly.
Depending on the type of child-restraint
system, it may use LATCH system instead
of seat belts or if the belt goes across the
child's chest, may recommend against
using automatic locking mode.
1. (Second-row seat)
Adjust the second-row seat position
using the following procedure.
Fold the second-row seatback
forward.
Raise the second-row seatback until
a click sound is heard and it is locked
in place.
2. Make sure the seatback is securely
latched by pushing it back until it is
fully locked.
Essential Safety Equipment
Child Restraint
2-44*Some models.
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

3.(Second-row seat)
Remove the head restraint. However,
when installing a backless booster seat,
always install the vehicle head restraint
to the seat where the backless booster
seat is installed.
Refer to Head Restraints on page 2-18.
4. Secure the child-restraint system with the lap portion of the lap/shoulder belt.
See the manufacturer's instructions on
the child-restraint system for belt
routing instructions.
5. To get the retractor into the automatic locking mode, pull the shoulder belt
portion of the seat belt until the entire
length of the belt is out of the retractor.6. Push the child-restraint system firmly
into the vehicle seat. Be sure the belt
retracts as snugly as possible. A
clicking noise from the retractor will
be heard during retraction if the system
is in the automatic locking mode. If the
belt does not lock the seat down tight,
repeat this step.
NOTE
•Inspect this function before each use
of the child-restraint system. You
should not be able to pull the
shoulder belt out of the retractor
while the system is in the automatic
locking mode. When you remove the
child-restraint system, be sure the
belt fully retracts to return the
system to emergency locking mode
before occupants use the seat belts.
7. If your child-restraint system requires the use of a tether strap, refer to the
manufacturer's instructions to hook
and tighten the tether strap.
Essential Safety Equipment
Child Restraint
2-45
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

WA R N I N G
Use the tether and tether anchor only for a
child-restraint system:
Using the tether or tether anchor to secure
anything but a child-restraint system is
dangerous. This could weaken or damage
the tether or tether anchor and result in
injury.
Always remove the head restraint and
install child-restraint system (except when
installing a backless booster seat)
(Second-row seat):
Installing a child-restraint system without
removing the head restraint is dangerous.
The child-restraint system cannot be
installed correctly which may result in
death or injury to the child in a collision.
Tether strap
Forward
Second-row
outboard seat

Tether strap
Forward
Second-row
center seat
Essential Safety Equipment
Child Restraint
2-46
CX-9_8GC3-EA-17G_Edition1
2017-5-29 10:13:38

Always attach the tether strap to the
correct tether anchor position:
Attaching the tether strap to the incorrect
tether anchor position is dangerous. In a
collision, the tether strap could come off
and loosen the child-restraint system. If the
child-restraint system moves it could result
in death or injury to the child.
Always install the head restraint and adjust
it to the appropriate position after
removing the child-restraint system
(Second-row seat):
Driving with the head restraint removed is
dangerous as impact to the occupant's
head cannot be prevented during
emergency braking or in a collision, which
could result in a serious accident, injury or
death.
Refer to Head Restraints on page 2-18.
Always route the tether straps to the sides
of the head restraint (Third-row seat):
Routing the tether straps on top of the
head restraint is dangerous. In a collision
the tether straps could slide off the head
restraint and loosen the child-restraint
system. The child-restraint system could
move which may result in death or injury to
the child.
Tether strap
ForwardThird-row seat
▼If You Must Use the Front Seat for
Children
If you cannot put all children in the rear
seat, at least put the
smallest children in
the rear and be sure the largest child up
front uses the shoulder belt over the
shoulder.
NEVER put a rear-facing child-restraint
system on the front passenger seat whether
your vehicle is equipped with an occupant
classification sensor or not.
This seat is also not set up for tethered
child-restraint system s, put them in one of
the rear seat positions set up with tether
anchors.
Likewise the LATCH child-restraint
system cannot be secured in the front
passenger's seat and should be used in the
second-row seat.
Do not allow anyone to sleep against the
side window since your vehicle has side
and curtain air bags, it could cause serious
injuries to an out of position occupant. As
children more often sleep in cars, it is
better to put them in the rear seat. If
installing the child-restraint system on the
front seat is unavoidable, follow these
instructions when using a front-facing
child-restraint system in the front
passenger's seat.
Essential Safety Equipment
Child Restraint
2-47
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38

NOTE
•To check if your front seats have side air
bags:
Mazda vehicles equipped with side air
bag will have a "SRS AIRBAG" tag on
the outboard shoulder of the front seats.
•To check if your vehicle has curtain air
bags:
Mazda vehicles equipped with curtain
air bag will have an "SRS AIRBAG"
marking on the window pillars along the
roof edge.
WA R N I N G
Always move the front passenger seat as
far back as possible if installing a
front-facing child-restraint system on it is
unavoidable:
As your vehicle has front air bags and
doubly so because your vehicle has side air
bags, a front-facing child-restraint system
should be put on the front passenger seat
only when it is unavoidable.
Even if the front passenger air bag
deactivation indicator light illuminates,
always move the seat as far back as
possible, because the force of a deploying
air bag could cause serious injury or death
to the child.
Never use a rear-facing child-restraint
system in the front seat with an air bag
that could deploy:
Rear-facing child-restraint systems on the
front seat are particularly dangerous.
Even in a moderate collision, the
child-restraint system can be hit by a
deploying air bag and moved violently
backward resulting in serious injury or
death to the child. Even though you may
feel assured that the front passenger air
bag will not deploy based on the fact that
the front passenger air bag deactivation
indicator light illuminates, you should not
use a rear-facing child-restraint system in
the front seat.
Do not allow a child or anyone to lean over
or against the side window of a vehicle
with side and curtain air bags:
It is dangerous to allow anyone to lean
over or against the side window, the area
of the front passenger seat, the front and
rear window pillars and the roof edge
along both sides from which the side and
curtain air bags deploy, even if a
child-restraint system is used. The impact
of inflation from a side or curtain air bag
could cause serious injury or death to an
out of position child. Furthermore, leaning
over or against the front door could block
the side and curtain air bags and eliminate
the advantages of supplemental
protection. With the front air bag and the
additional side air bag that comes out of
the front seat, the rear seat is always a
better location for children. Take special
care not to allow a child to lean over or
against the side window, even if the child is
seated in a child-restraint system.
Essential Safety Equipment
Child Restraint
2-48
CX-9_8GC3-EA-17G_Edition1 2017-5-29 10:13:38