clock MAZDA MODEL MPV 2004 Owners Manual (in English)

3-18
Knowing Your Mazda
Doors and Locks
Form No. 8S06-EA-03H

Locking, Unlocking with Key
To lock the liftgate with the key, insert the
key and turn it counterclockwise.
To unlock the liftgate with the key, insert
the key and turn it clockwise.
The liftgate can be locked/unlocked by
inserting the key into the key slot of any
door, refer to Power Door Locks (page
3-10).
Turn Power Sliding Doors Main
Switch OFF When Working on
Vehicle:
Leaving the power sliding doors main
switch in the ON position while
working on the vehicle is dangerous.
If the open/close switches are
mistakenly pressed, the power sliding
doors will slide and hands or head
could become caught resulting in
possible injury. Always press the
power sliding doors main switch to
the OFF position when working on
the vehicle.
NOTE
•If there is a problem with the power
sliding doors and you want to
operate them manually, press the
power sliding doors main switch to
the OFF position and they can be
operated manually.
•If the power sliding doors main
switch is pressed to the OFF
position while the doors are
opening/closing electrically, the
beep sound will be heard and the
sliding door(s) stop.
If you press the power sliding doors
main switch to the ON position
again, the door(s) can be opened/
closed electrically.
•When a sliding door is half open
and the system is switched to
manual operation, the door can be
operated manually by first sliding it
forward and back, and then in the
desired direction.
WARNINGLiftgate
Open Liftgate:
An open liftgate in a moving vehicle
will cause exhaust gas to be drawn
into the cabin. This gas contains CO
(carbon monoxide), which is
colorless, odorless, and highly
poisonous, and it can cause loss of
consciousness and death. Moreover,
an open liftgate could cause
occupants to fall out in an accident.
Do not drive with the liftgate open.
WARNING
LockUnlock
J16R_8S06-EA-03H_Edition1.book Page 18 Wednesday, July 9, 2003 4:19 PM

3-23
Knowing Your Mazda
Doors and Locks
Form No. 8S06-EA-03H

Fuel-Filler Lid
To open, pull up the remote fuel-filler lid
release.

Fuel-Filler Cap
To remove the filler cap, turn it
counterclockwise.
To close the filler cap, turn it clockwise
until it clicks.
Fuel-Filler Lid and Cap
Fuel Spray:
Fuel spray is dangerous. Fuel can
burn skin and eyes and cause illness
when ingested. Fuel spray is released
when there is pressure in the fuel
tank and the fuel cap is removed too
quickly. When removing the fuel cap,
loosen the cap slightly and wait for
any hissing to stop. Then remove it.
Fuel Vapor:
Fuel vapor is dangerous. It could be
ignited by sparks or flames causing
serious burns and injuries. Before
refueling, stop the engine, and always
keep sparks and flames away from the
filler neck. Additionally, use of the
incorrect fuel filler cap or not using a
fuel filler cap may result in fuel leak,
which could result in serious burns or
death in an accident.
Always use only a genuine Mazda fuel
cap or an approved equivalent,
available at Authorized Mazda
Dealers. The wrong cap can result in a
serious malfunction of the fuel and
emission control systems. It may also
cause the check engine light in the
instrument cluster to illuminate.
WARNING
CAUTION
NOTE
The fuel-filler lid cannot be opened
when the left-side sliding door is open.
Close the sliding door to open the fuel-
filler lid.
Remote fuel-filler
lid release
Open
Close
J16R_8S06-EA-03H_Edition1.book Page 23 Wednesday, July 9, 2003 4:19 PM

6-5
Interior Comfort
Climate Control System
Form No. 8S06-EA-03H

Control Switches
Temperature control dial
This dial controls temperature. Turn it
clockwise for hot and counterclockwise
for cold.Fan control dial
This dial allows variable fan speeds.
0—Fan off
1—Low speed
2—Medium low speed
3—Medium high speed
4—High speed
Control Panel (Front)
A/C0123
4
0123REAR
Temperature control dialA/C switch Rear window defroster switchFan control dial
Air intake selector switch
Rear air-conditioner main switchMode selector dial
(page 5-38)
(page 6-12)
ColdHot
J16R_8S06-EA-03H_Edition1.book Page 5 Wednesday, July 9, 2003 4:19 PM

6-14
Interior Comfort
Form No. 8S06-EA-03H
Audio System

Detachable Type
To remove the antenna, turn it
counterclockwise.
To install the antenna, turn it clockwise.
Make sure the antenna is securely
installed.
Antenna
To prevent damage to the antenna,
remove it before entering a car wash
facility or passing beneath a low
overhead clearance.
NOTE
When leaving your vehicle unattended,
we recommend that you remove the
antenna and store it inside the vehicle.
CAUTION
Operating Tips for Audio
System
Do Not Adjust Audio While Driving
the Vehicle
Adjusting the audio while driving the
vehicle is dangerous as it could
distract your attention from the
vehicle operation which could lead to
a serious accident. Always adjust the
audio while the vehicle is stopped.
For the purposes of safe driving, adjust
the audio volume to a level that allows
you to hear sounds outside of the
vehicle.
NOTE
•Do not use the audio for long
periods of time while the engine is
off. Otherwise the battery could go
dead.
•If a digital cellular phone or CB
radio is used in or near the vehicle,
it could cause noise to occur from
the audio system, however, this does
not indicate that the system has
been damaged.
WARNING
CAUTION
J16R_8S06-EA-03H_Edition1.book Page 14 Wednesday, July 9, 2003 4:19 PM

6-21
Interior Comfort
Au di o S ys t em
Form No. 8S06-EA-03H
Power/Volume/Sound Controls ............................................................................................. 6-22
Clock ..................................................................................................................................... 6-24
Operating the Radio ............................................................................................................... 6-26
Operating the Cassette Tape Player* ..................................................................................... 6-28
Operating the Mini Disc (MD) Player* ................................................................................. 6-30
Operating the Compact Disc (CD) Player* ........................................................................... 6-32
Operating the In-Dash CD Changer* .................................................................................... 6-34
Error Indications .................................................................................................................... 6-37
Audio Set*
CD Player* In-dash CD Changer*
Cassette Tape Player* Mini Disc (MD) Player*Illustration is of a representative audio unit.
*Some models.
J16R_8S06-EA-03H_Edition1.book Page 21 Wednesday, July 9, 2003 4:19 PM

6-24
Interior Comfort
Au di o S ys t em
Form No. 8S06-EA-03H

Clock
Setting the time
The clock can be set at any time when the
ignition switch is in the ACC or ON
position.
1. To adjust the time, press the clock
button ( ) for about 2 seconds
until a beep is heard.
The clock’s current time will flash.2. To advance the hours, press the hour
set button ( ). To advance the
minutes, press the minute set button
( ) while the time is flashing.
3. Press the clock button ( ) again
to start the clock.
Display
Clock button
Hour set
button
Minute set
button
NOTE
To select 12-hour or 24-hour clock
time, turn the audio control dial while
the clock display is flashing. After
selecting the desired display, press the
audio control dial to return to the
flashing clock display.
J16R_8S06-EA-03H_Edition1.book Page 24 Wednesday, July 9, 2003 4:19 PM

6-25
Interior Comfort
Au di o S ys t em
Form No. 8S06-EA-03H
Exact hour adjustment
1. To set the exact hour, press the clock
button ( ) for about 2 seconds
until a beep is heard.
The clock’s current time will flash.
2. Press the clock button ( ) again
and the time will be adjusted as
follows:
(Example)
12:01—12:29
→12:00
12:30—12:59
→1:00
Changing the display mode
The display on the unit can be changed by
pressing the clock button ( ). This
alternates the display between clock mode
and normal mode. When the clock mode
has been selected, the time will be
displayed.
NOTE
•When the clock button ( ) is
released, the seconds are reset to
"00".
•If the power supply to the unit is
interrupted (if the fuse blows or the
vehicle’s battery is disconnected),
the clock will need to be reset.
NOTE
The displays when using the audio
differ in clock mode and normal mode.
J16R_8S06-EA-03H_Edition1.book Page 25 Wednesday, July 9, 2003 4:19 PM

6-27
Interior Comfort
Au di o S ys t em
Form No. 8S06-EA-03H
Seek tuning
Pressing the seek tuning button
( , ) will cause the tuner to seek a
higher or lower frequency automatically.
Scan tuning
Press the scan button ( ) to
automatically sample strong stations.
Scanning stops at each station for about 5
seconds. To hold a station, merely press
the scan button ( ) again during this
interval.
Preset channel tuning
The 6 preset channels can be used to store
6 AM and 12 FM stations.
1. To set a channel first select AM, FM1,
or FM2. Tune to the station you want.
2. Depress a channel preset button for
about 2 seconds until a beep is heard.
The preset channel number and station
frequency will be displayed. The
station is now held in the memory.
3. Repeat this operation for the other
stations and bands you want to store.
To tune one in the memory, select AM,
FM1, or FM2 and then press its
channel preset button. The station
frequency and the channel number will
be displayed.Auto memory tuning
This is especially useful when driving in
an area where the local stations are not
known. Additional AM/FM stations can
be stored without disturbing the
previously set channels.
Press and hold the auto memory button
( ) for about 2 seconds until a beep
is heard; the system will automatically
scan and temporarily store up to 6 stations
with the strongest frequencies in each
selected band in that area.
After scanning is completed, the station
with the strongest frequency will be tuned
and its frequency displayed.
Press and release the auto memory button
( ) to recall stations from the auto-
stored stations. One stored station will be
selected each time; its frequency and
channel number will be displayed.
NOTE
If you continue to press and hold the
button, the frequency will continue
changing without stopping.
NOTE
When the clock is displayed, the preset
channel number will not be displayed.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the preset channels will be canceled.
NOTE
•When the clock is displayed, the
preset channel number will not be
displayed.
•If no stations can be tuned after
scanning operations, "A" will be
displayed.
J16R_8S06-EA-03H_Edition1.book Page 27 Wednesday, July 9, 2003 4:19 PM

6-30
Interior Comfort
Au di o S ys t em
Form No. 8S06-EA-03H

Operating the Mini Disc (MD) Player*
Inserting the MD
Insert the MD, label-side up with the
arrow pointed to the slot. The auto-
loading mechanism will set the MD and
begin play. There will be a short lapse
before play begins while the player reads
the digital signals on the MD.
The track number and the elapsed play
back time for the current track will be
displayed on the display.PlayingPress the MD play button ( ) to
start playing when a MD is in the unit.
Ejecting the MD
Press the MD eject button ( ) to eject the
MD.
Fast-forward/Reverse
Press and hold the fast-forward button
( ) to advance through a track at high
speed.
Press and hold the reverse button ( )
to reverse through a track at high speed.
Tr a c k s e a r c h
Press the track up button ( ) once to
skip forward to the beginning of the next
track.
Press the track down button ( ) once to
skip back to the beginning of the current
track.
MD play button
Random button Repeat buttonFast-forward button
Reverse
button Scan
button
Track up
button
Track down
button
MD slot
MD display
button
MD eject button
MD display
Main display
Display
button
Display
feed dial
NOTE
When the clock is displayed, the
elapsed play back time will not be
displayed. To display the elapsed play
back time, turn the audio control dial
to the right. Turn the dial to the left to
return to the previous display.
*Some models.
J16R_8S06-EA-03H_Edition1.book Page 30 Wednesday, July 9, 2003 4:19 PM

6-32
Interior Comfort
Au di o S ys t em
Form No. 8S06-EA-03H

Operating the Compact Disc (CD) Player*
Inserting the CD
Insert the CD into the slot, label-side up.
The auto-loading mechanism will set the
CD and begin play. There will be a short
lapse before play begins while the player
reads the digital signals on the CD.
The disc-in indicator will illuminate, and
the track number and the elapsed play
back time for the current track will be
displayed.PlayingPress the CD play button ( ) to start
playing when a CD is in the unit.
Ejecting the CD
Press the CD eject button ( ) to eject the
CD.
Fast-forward/Reverse
Press and hold the fast-forward button
( ) to advance through a track at high
speed.
Press and hold the reverse button ( )
to reverse through a track at high speed.
Display CD slotCD play button CD eject button
Random button
Repeat buttonFast-forward button
Reverse
button Scan
button
Track up
button
Track down
button
Disc-in indicator
NOTE
When the clock is displayed, the
elapsed play back time will not be
displayed. To display the elapsed play
back time, turn the audio control dial
to the right. Turn the dial to the left to
return to the previous display.
*Some models.
J16R_8S06-EA-03H_Edition1.book Page 32 Wednesday, July 9, 2003 4:19 PM