ev system MAZDA MODEL MX-30 EV 2022 Owners Manual

▼Seat Belt Warning Light (Rear seat)
(Red)
If the rear seat belts are not fastened
while the power switch is switched
ON , the driver and the passenger are
alerted by the warning light.
The warning light operates even if there
is no passenger on the rear seat.
NOTE
If a rear seat belt is not fastened by a
certain period of time after the EV
system has been started, the warning
light turns o
ff.
Action to be taken
Fasten the seat belts.
▼ Low Washer Fluid Level Warning
Indication/Warning Light*
This warning light indicates that little
washer
fluid remains.
Action to be taken
Add washer fluid (page 6-13).
▼ Door-Ajar/Liftgate-Ajar Warning
Indication/Warning Light
The light turns on if any door/liftgate is
not closed securely.
Action to be taken
Close the door/liftgate securely.
▼ Tire Pressure Monitoring System
(TPMS) Warning Indication/
Warning Light (Turns on)
If a tire pressure decreases below the
speci
fied air pressure, the TPMS
warning light turns on.
At the same time, a message and the
tire pressure of each tire are displayed
on the multi-information display
alternately. In addition, the tire (s) with
low air pressure is displayed in yellow.
WARNING
Do not drive the vehicle at high
speeds if the TPMS warning light turns
on or flashes:
Driving the vehicle at high speeds
while the TPMS warning light is turned
on or flashing is dangerous because
the brake performance and the
steering wheel operability will be
reduced. If the vehicle is driven at high
speeds or the brakes are suddenly
applied, it could lead to an accident.
Gradually apply the brakes to lower the
vehicle's speed.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-30*Some models.
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Do not ignore the TPMS warning light
when it is turned on or flashing:
Continuing to drive the vehicle while
ignoring the illumination/ flashing of
the TPMS warning light is dangerous
because a tire may burst which could
lead to an accident. Take appropriate
measures as soon as possible.
NOTE
While the TPMS is learning the tire
positions, such as immediately after a
tire position has been changed, the tire
pressure at the tire position prior to it
being changed is displayed until the
system completes the learning. For this
reason, the tire pressures displayed for
the tire positions may be di fferent from
the actual tire pressures at the tire
positions.
Action to be taken
Adjust the tire pressures to the
appropriate pressures.
Refer to Tire In flation Pressure on page
6-23.
CAUTION
 Adjust the tire pressures while the
tires are cool. Because the air
pressure in the tires fluctuates
depending on the temperature,
before adjusting the tire pressures,
let the vehicle sit for an hour or drive
it only within a 1.6 km (1 mile)
distance. If the tire pressures are
adjusted while the tires are warm,
the tire pressures may decrease
below the specified air pressure after
cooling down which could turn on
the warning light. In addition,
because the air pressure in the tires
decreases when the ambient
temperature is low, if the ambient
temperature increases, an
illuminated TPMS warning light may
turn o ff. Under any circumstances,
always adjust the tire pressures while
the tires are cool.
 After adjusting the tire pressures, the
TPMS warning light turns o ff. If the
TPMS warning light does not turn off,
drive the vehicle at a speed of about
25 km (16 mph) or faster for 3
minutes or longer and make sure the
warning light turns off.
If the TPMS warning light remains on
even after adjusting the tire pressures,
one of the tires may have a puncture.
▼ KEY Indicator Light (Green)
(Flashing)
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-31
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Message Indicated on Multi-information Display
▼Message Indicated on Multi-information Display
If there is a noti
fication from the vehicle, a message is displayed on the
multi-information display. Check the information and take the necessary action.

1. Multi-information display

If the warning light turns on/flashes simultaneously or a symbol is indicated on the
display, check the information regarding the warning light or symbol.
Refer to If a Warning Light Turn s On or Flashes on page 7-21.
Display*1*2Content Action to be taken
Depress Brake Pedal.
Brake Hold Disabled This message is indicated when there
is a problem with the brake related
system while the vehicle is being held
in a stop position by the AUTOHOLD
function. Depress the brake pedal. Cancel the
AUTOHOLD function and have your
vehicle inspected at an Authorized
Mazda Dealer.
Steep Slope. Continue
Pressing Brake Pedal to
Hold Stopped Position This message indicates the possibility
of the vehicle not being held in the
stopped position by the AUTOHOLD
function, such as on steep slopes.
Depress and hold your foot on the
brake pedal.
Depress Brake Pedal and
Operate Switch to Re-
lease Elec. Parking Brake This message is indicated when the
Electric Parking Brake (EPB) switch is
operated without depressing the
brake pedal. Operate the Electric Parking Brake
(EPB) switch while depressing the
brake pedal.
Depress Brake Pedal and
Operate Switch to Re-
lease This message is indicated when the
cancel operation is done without de-
pressing the brake pedal while the
vehicle is being held in the stopped
position by the AUTOHOLD function. Cancel the AUTOHOLD function stop
hold control while depressing the
brake pedal.
Mazda Radar Cruise
Control Canceled. Drive
Safely This message is indicated when the
Mazda Radar Cruise Control with
Stop & Go function (MRCC with Stop
& Go function) have been canceled
other than by the driver.
Have your vehicle inspected by an
Authorized Mazda Dealer.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-33
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Display*1*2ContentAction to be taken
Tra ffic Jam Assist Opera-
tion Canceled Drive
Safely This message is indicated when the
Tra
ffic Jam Assist (TJA) have been can-
celed other than by the driver. Have your vehicle inspected by an
Authorized Mazda Dealer.
Distance & Speed Alert
Operation Canceled
Drive Safely This message is indicated when the
Distance & Speed Alert (DSA) have
been canceled other than by the driv-
er.
Have your vehicle inspected by an
Authorized Mazda Dealer.
Cruise Control Opera-
tion Canceled. Drive
Safely This message is indicated when the
Cruise Control have been canceled
other than by the driver.
Have your vehicle inspected by an
Authorized Mazda Dealer.
Emergency Braking Acti-
vated. Depress Brake
Pedal to Hold Stop This message is indicated after the
Smart Brake Support (SBS) brakes op-
erate and when the SBS is canceled.
Depress the brake pedal.
Touch Key Fob to Push
Button Start Switch This message is indicated when the
key battery is weak (battery dead or
damaged key). Touch the key against power switch
to start the EV system.
Refer to Starting the EV System When
the Key Battery is Dead on page 4-6.
Depress Brake Pedal to
Start Vehicle This message is displayed when the
power switch is pressed without de-
pressing the brake pedal. To start the EV system, press the pow-
er switch with the brake pedal de-
pressed.
Check Shift Selector Lev-
er Position Displays in the following cases:
Selector lever is shifted to R posi-
tion while driving forward.
Selector lever is shifted to P posi-
tion while driving.
Selector lever is shifted to D posi-
tion while reversing.
Check the selector lever position.
Close Door and Fasten
Seat Belt This message is indicated when the
AUTOHOLD switch is pressed with
the driver’s seat belt unfastened or
the driver’s door open. Fasten the driver's seat belt and press
the AUTOHOLD switch with the driv-
er’s door closed.
Wiper Blades Must Be
on Windshield Before
Operating This message is indicated when the
power switch is switched ON with
the wiper arms at the service posi-
tions.
Return the wiper arms to the initial
positions.
Windshield Wiper Range
of Motion Reduced. Re-
move Obstruction(s) This message is indicated when there
is snow or dirt accumulation on the
windshield and the wiper operation
range is narrowed.
Remove foreign matter from the
windshield.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-34
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Display*1*2ContentAction to be taken
Anti Roll Away Engaged.
Move Gear Selector Lev-
er into Park This message is indicated when the
AUTO P (parking lock) function oper-
ates.
Shift the selector lever to the P posi-
tion.
Move Gear Selector Lev-
er into Park to Start Ve-
hicle This message is indicated when the
power switch is switched ON while
the shift position is diff
erent from the
selector lever position. Shift the selector lever to the P posi-
tion.
Vehicle Will Not Shift
While Accelerator Pedal
Is Depressed This message is indicated when the
accelerator pedal is depressed with
the selector lever in the N position.
Release your foot from the accelera-
tor pedal.
Selector Position Ignor-
ed. Depress Brake Pedal
for Shift Selection This message is indicated when the
selector lever is shifted from the N
position to the D or R position with
the brake pedal not depressed.
Depress the brake pedal.
Ve h i c l e i n N e u t ra l This message is displayed when in
neutral hold mode (automatic car
wash mode). The vehicle is in neutral hold mode
(automatic car wash mode). If neces-
sary, cancel neutral hold mode (auto-
matic car wash mode).
Refer to Selector Lever Operation on
page 4-28.
Vehicle in Neutral. Move
Gear Selector Lever into
Neutral This message is indicated if the selec-
tor lever is shifted to the D or R posi-
tion while neutral hold mode (auto-
matic car wash mode) is operating.
Shift the selector lever to the N posi-
tion.
Disconnect Charger to
Start Vehicle This message is indicated when the
EV system is started while the charge
connector is connected. When starting the EV system, discon-
nect the charge connector.
EV Charger Connected.
Vehicle Cannot Be Driv-
en This message is indicated when the
charge connector is connected while
the EV system is operating.
When charging , switch the power
switch OFF.
Battery Heater Will Re-
duce High Voltage Bat-
tery Level Connect to EV
Charger To Avoid High
Voltage Battery Drain This message is indicated when the
EV system is started after the battery
heater has operated while the charge
connector is not connected.
Check the remaining distance-to-full
discharge. Perform charging if neces-
sary.
Battery Heating Incom-
plete Due to High Volt-
age Battery Level Con-
nect to EV Charger To
Avoid High Voltage Bat-
tery Drain This message is displayed when the
EV system is started after the battery
heater stops automatically.
If the battery heater operates while
the vehicle is parked, connect the
charge connector.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-35
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Display*1*2ContentAction to be taken
Battery Heating Can-
celed Due to Five Days
of Vehicle Inactivity Turn
Battery Heater O ff If Ve-
hicle Will Not Be Driven This message is displayed when the
EV system is started after the battery
heater has operated for a long time
and stopped automatically.
If the vehicle is not used for long pe-
riods, set the battery heater to o
ff.
High Voltage Battery
Charging Interrupted This message is displayed when the
charging is interrupted. Check the connection status of the
charge connector.
Rising EV System Temp.
Acceleration May Be
Limited Avoid Moving at
Very Low Speeds. De-
press Brake When Not
Moving This message is indicated when the
vehicle is held in the stopped posi-
tion with the accelerator pedal oper-
ated, such as on an upslope, and the
motor reaches a high temperature.
Depress the brake pedal.
Regenerative Braking Is
Limited This message is indicated when the
regenerative braking is restricted. Drive the vehicle carefully because
the regenerative braking force de-
creases.
Shift Into Park Before Ex-
iting Vehicle This message is indicated when the
driver’s door is opened with the se-
lector lever in a position other than
the P position. Close the driver’s door or shift the se-
lector lever to the P position.
Low Battery Risk. Start
Vehicle to Charge 12V
Battery This message is indicated when the
lead-acid battery charge is low.
To charge the lead-acid battery, start
the EV system and operate it for 5 mi-
nutes or longer.
*1 A pop-up is displayed when a warning occurs.*2 One screen displays four rows. If the entire message cannot be displayed on the screen, it switches to
another screen.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-36
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Warning Sound isActivated
▼Lights-On Reminder
The lights-on reminder is operable
when the time setting*1 of the auto
headlight o ff function is o ff.
If the power switch is switched OFF
with the exterior li ghts turned on and
the driver’s door is opened, a sound is
activated.
Operate the headlight switch to turn
o ff the exterior lights.
*1 If the light switch is left on, the
auto headlight o ff function
automatically turns off the lights
about 30 seconds after switching
the EV system off. The time setting
can be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
NOTE
When the power switch is switched
to ACC, the “Power Switch Not
Switched OFF (STOP) Warning Beep”
(page 7-37) overrides the lights-on
reminder.
A personalized function is available
to change the sound volume for the
lights-on reminder.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼ Seat Belt Warning Beep
Front seat
If the driver's seat belt is not fastened
when the power switch is switched
ON, a beep sound will be heard for
about 6 seconds. If the driver or the
front passenger's seat belt is not
fastened and if the vehicle is driven at
about 20 km/h (12 mph) or faster, or
about 10 km/h (6 mph) or faster for a
continuous 30 seconds, with the seat
belt unfastened, a sound is activated
continuously for a certain period.
Until a seat belt is fastened or a given
period of time has elapsed, the beep
sound will not stop even if the vehicle
speed falls below 20 km/h (12 mph).
NOTE
To allow the front passenger
occupant classi
fication sensor to
function properly, do not place and
sit on an additional seat cushion on
the front passenger's seat. The
sensor may not function properly
because the additional seat cushion
could cause sensor interference.
If a small child is seated on the front
passenger's seat, the warning beep
may not operate.
Rear seat
The warning beep only sounds if a seat
belt is unfastened after being fastened.
▼ Power Switch Not Switched OFF
(STOP) Warning Beep
If the driver's door is opened with the
power switch switched to ACC, a beep
will be heard continuously in the cabin
to notify the driver that the power
switch has not been switched OFF
(STOP). Under this condition, the
keyless entry system will not operate,
the vehicle cannot be locked, and the
battery voltage will be depleted.
▼Key Removed from Vehicle
Warning Beep
Vehicles with advanced keyless
function
If the key is taken out of the vehicle
while the power switch is switched to
ACC or ON, and all the doors are
closed, a sound is activated 6 times
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-37
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

▼Brake System Warning Beep
A warning beep is activated if a
problem with the brake system occurs
and the brakes may not work as
intended. Decelerate the vehicle while
checking the safety of the surrounding
area, and park the vehicle in a safe
place. After stopping the vehicle,
contact an Authorized Mazda Dealer.
▼Brake Override Warning Beep
A warning beep is activated when the
accelerator pedal and brake pedal are
depressed at the same time while
driving. Only depress the brake pedal.
▼Shift Position Warning Beep
A warning sound is activated when the
selector lever position and the shift
position of the vehicle do not match.
Check the selector lever position.
▼Selector Lever Not In P or N
Reminder Warning Beep
A warning sound is activated if the
following operations are performed
while the selector lever is in a position
other than P.
The power switch is switched OFF
while the EV system is operating.
The driver’s seat belt is unfastened
and the driver’s door is opened.
Check the selector lever position.
▼ Electric Parking Brake (EPB)
War n in g Be ep
The warning buzzer is activated under
the following conditions:
The vehicle is driven with the parking
brake applied.
The Electric Parking Brake (EPB)
switch is pulled while the vehicle is
driven.
You attempt to start driving the
vehicle while the conditions for
releasing the Electric Parking Brake
(EPB) automatically have not been
met.
▼
AUTOHOLD Warning Beep
Message is displayed and beep sound
is activated simultaneously for about 5
seconds when using AUTOHOLD
function or when AUTOHOLD switch
is operated.
Because a problem with AUTOHOLD
function has occurred, AUTOHOLD
function does not operate even if
AUTOHOLD switch is operated.

If the message is displayed and the
beep sound is activated
simultaneously, have your vehicle
inspected at an Authorized Mazda
Dealer.
▼Vehicle Problem Warning Beep
If any of the following problems occur,
a warning beep is activated. Check the
information regarding the warning
indication in the instrument cluster or
on the center display.
Brake
fluid amount decreaseElectric Parking Brake (EPB) problemShift control system problemEV System problemCharging system problemApproaching vehicle audible system
problem
▼Reverse Position Warning Beep
The warning beep is activated when
the power switch is switched ON and
the selector lever is in the R position.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-39
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

▼Blind Spot Monitoring (BSM)
System Warning Beep*
The Blind Spot Monitoring (BSM)
warning beep operates when the turn
signal lever is operated to the side
where the Blind Spot Monitoring
(BSM) warning light is illuminated.
▼Front Cross Tra
ffic Alert (FCTA)
Warning Beep*
The Front Cross Tra ffic Alert (FCTA)
warning beep is activated if there is a
possibility of collision with a vehicle
approaching from the front on the left
and right sides of the vehicle.
▼ Rear Cross
Traffic Alert (RCTA)
Warning Beep*
The Rear Cross Tra ffic Alert (RCTA)
warning beep is activated if there is a
possibility of collision with a vehicle
approaching from the rear on the left
and right sides of the vehicle.
▼ Lane/Road Departure Warning
Beep*
The warning beep is activated when
the system determines that the vehicle
may depart from the lane or the road.
Check whether the vehicle has not
deviated from the driving lane/road.
▼Mazda Radar Cruise Control with
Stop & Go function (MRCC with
Stop & Go function) System
Warnings
*
The Mazda Radar Cruise Control with
Stop & Go function (MRCC with Stop
& Go function) system warnings notify
the driver of system malfunctions and
cautions on use when required.
Check based on the beep sound.
Warning beep type Noti
fication content
The beep sounds 1
time while the Mazda
Radar Cruise Control
with Stop & Go func-
tion (MRCC with Stop
& Go function) is op-
erating. If a malfunction occurs
in the system, make
sure that the Mazda
Radar Cruise Control
with Stop & Go func-
tion (MRCC with Stop
& Go function) has
been canceled.
The beep sounds in-
termittently while the
Mazda Radar Cruise
Control with Stop &
Go function (MRCC
with Stop & Go func-
tion) is operating. The distance between
your vehicle and the
vehicle ahead is too
close. Check the safety
of the surrounding
area and reduce vehi-
cle speed.
▼
Excessive Speed Warning*
If the vehicle speed exceeds the speed
limit sign displayed in
the active driving
display/instrument cluster, the area
around the speed limit sign flashes in
amber and the warning sound is
activated at the same time. If the
vehicle speed continues to exceed the
displayed speed limit sign, the
indication stops flashing and remains
on.
▼ Collision warning*
If there is a possibility of a collision
with a vehicle ahead, a warning sound
is activated at the same time as the
warning indications are displayed in
the instrument cluster or active driving
display.
▼Door-ajar Warning Beep
A warning beep is activated if the
vehicle is driven with any door or
liftgate ajar. Drive the vehicle after
closing the doors and liftgate.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-40*Some models.
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

▼Low Lead-acid Battery Charge
Warning Sound
The warning sound is activated when
the lead-acid battery charge is low.
To charge the lead-acid battery, start
the EV system and operate it for 5
minutes or longer.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-41
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07