steering MAZDA MODEL MX-30 EV 2022 Owner's Manual

Stopping the EV System
▼When Stopping the EV System
1. Shift the selector lever to the P
position.
2. Press the power switch. The READY
indication is not displayed in the
instrument cluster and the EV
system stops, and then the power
switch is switched OFF.
WARNING
Other than for an emergency
situation, do not attempt to stop the
EV system while driving the vehicle:
If the EV system is stopped while
driving the vehicle, loss of brake power
and power steering functions could
occur, making it di fficult to control the
vehicle which could result in an
accident.
CAUTION
Before leaving the vehicle, make sure
that the power switch is switched OFF
(READY indication is not displayed).
NOTE
Key battery
If the system detects that the key's
remaining battery power is low when
the power switch is switched from
ON to ACC or OFF, the KEY indicator
light (green) flashes in the instrument
cluster or the KEY warning indication
is displayed on the multi-information
display.
Refer to Starting the EV System When
the Key Battery is Dead on page 4-6.
Selector lever position
Because the AUTO P (parking lock)
function operates, the power
switch can be switched OFF even
with the selector lever in a position
other than P, however, for reasons
of safety, shift the selector lever to
the P position and then switch the
power switch OFF.
If you switch the power switch OFF
with the selector lever in a position
other than P, a warning sound and
a display indication notify you that
the selector lever position and the
shift position do not match.
Power switch position
If you leave or try to leave the vehicle
without switching the power switch
OFF, the KEY warning light (red) fl ashing , a display indication, and a
warning sound notify you that the
power switch is not switched OFF.
▼ Emergency EV System Stop
Pressing the power switch continuously
or pressing it quickly any number of
times even if the vehicle is not
stopped, will stop the EV system. The
power switch switches to ACC.
When Driving
Starting and Stopping the EV System
4-8
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

▼Warning Indication/Warning Lights
These lights turn on or
flash to notify the user of the system operation status or a
system malfunction.
Signal Warning Refer to
Brake System Warning Indication/Warning Light*17-21
ABS Warning Indication/Warning Light*1
Electronic
Brake Force
Distribution
System Warn- ing
7-22
ABS warning 7-26
Lead-acid Battery Charging System Warning Indication/Warning
Light*17-22
EV System Problem Warning Indication/Warning Light*17-22
High Voltage Battery Temperature Warning Indication 7-23
Remaining High Voltage Battery Power Warning Indication/Warning
Light*17-23
Charging System Warning Indication/Warning Light*17-24
Output Restriction Warning Indication/Warning Light*17-24
Power Steering Malfunction Indication/Indicator Light*17-25
Shift Control System Warning Indication/Warning light*17-25
Master Warning Indication7-26
Brake Control System Warning Indication/Warning Light*17-26
Brake Override Warning Indication7-26
When Driving
Instrument Cluster and Display
4-19
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Pa r k i n g t h e v e h i c l e
1. After completely stopping thevehicle, continue to depress the
brake pedal firmly.
2. Shift the selector lever to the P
position with the brake pedal
depressed.
3. Make sure that the shift position is in the P position using the shift
position indication in the
instrument cluster.
4. Apply the parking brake with the
brake pedal depressed.
5. Press the power switch to stop the
EV system.
CAUTION
Completely stop the vehicle before
shifting the selector lever to the P
position. If the selector lever is shifted
to the P position before the vehicle is
completely stopped, unnecessary force
will be applied to the EV transaxle
which could cause damage.
Other precautions
WARNING
Do not allow the vehicle to move in
reverse on an upslope while the
selector lever is in forward drive, or
move forward on an downslope while
the selector lever is in reverse drive:
Otherwise, the EV system could stop,
making the steering wheel difficult to
control, which could result in an
accident.
When Driving
Selector Lever Position Functions
4-34
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

to operate the windshield wiper
de-icer (page 4-45).
1. Indicator light
▼Mirror Defogger*
The mirror defoggers defrost the
outside mirrors.

The mirror defoggers operate in
conjunction with the rear window
defogger.
Press the rear window defogger switch
when the power switch is switched ON
to operate the mirror defoggers (page
4-45).
1. Indicator light
Horn
▼ Horn
To sound the horn, press the
mark on the steering wheel.
When Driving
Switches and Controls
4-46*Some models.
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

AUTOHOLD
▼AUTOHOLD
The AUTOHOLD function automatically holds the vehicle stopped, even if you take
your foot
off the brake pedal. This function can be best used while stopped in
traffic
or at a traffic light. The brakes are released when you start driving the vehicle.
WARNING
Do not rely completely on the AUTOHOLD function:
The AUTOHOLD function is only designed to assist the brake operation while the
vehicle is stopped. Neglecting to operate the brakes and relying only on the
AUTOHOLD system is dangerous and could result in an unexpected accident if the
vehicle were to suddenly move. Operate the brakes appropriately in accordance
with the road and surrounding conditions.
Do not release your foot from the brake pedal while the vehicle is stopped on a
steep grade:
Because there is a possibility of the vehicl
e not being held in the stopped position by
the AUTOHOLD function, the vehicle may move unexpectedly and result in an
accident.
Do not use the AUTOHOLD function on slippery roads such as icy or
snow-covered roads, or unpaved roads:
Even if the vehicle is held in the stopped position by the AUTOHOLD function, the
vehicle may move unexpectedly and result in an accident. Operate the accelerator
pedal, brakes, or steering wheel appropriately as necessary.
Immediately depress the brake pedal in the following cases:
Because the AUTOHOLD function is canceled forcibly, the vehicle may move
unexpectedly and result in an accident.
 “Depress Brake Pedal. Brake Hold Disabled” is displayed in the multi-information
display and the warning sound is activated at the same time.
Always apply the parking brake when parking the vehicle:
Not applying the parking brake when parking the vehicle is dangerous as the vehicle
may move unexpectedly and result in an accident. When parking the vehicle, shift
the selector lever to the P position and apply the parking brake.
When Driving
Brake
4-57
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Dynamic Stability Control(DSC)
▼Dynamic Stability Control (DSC)
The Dynamic Stability Control (DSC)
automatically controls braking and
motor torque in conjunction with
systems such as the ABS and TCS to
help control side slip when driving on
slippery surfaces, or during sudden or
evasive steering, which enhances
vehicle stability.

Refer to ABS (page 4-63) and TCS
(page 4-64).

DSC operation is possible at speeds
greater than 20 km/h (12 mph).

The warning light turns on when the
system has a malfunction.
Refer to TCS/DSC Indication/
Indicator Light (Turns on) on page
7-27.
WARNING
Do not rely on the Dynamic Stability
Control as a substitute for safe
driving:
The Dynamic Stability Control (DSC)
cannot compensate for unsafe and
reckless driving , excessive speed,
tailgating (following another vehicle
too closely), and hydroplaning
(reduced tire friction and road contact
because of water on the road surface).
You can still have an accident.
CAUTION

The DSC may not operate correctly
unless the following are observed:
 Use tires of the correct size
speci fied for your Mazda on all 4
wheels.
 Use tires of the same
manufacturer, brand and tread
pattern on all 4 wheels.
 Do not mix worn tires.
 The DSC may not operate correctly
when tire chains are used or a
temporary spare tire is installed
because the tire diameter changes.
NOTE
If there is a problem with the DSC, the
Hill Launch Assi st (HLA) may not
operate.
Refer to Hill Launch Assist (HLA) on
page 4-61.
▼ TCS/DSC Indicator Light
When the power switch is switched
ON, the TCS/DSC indicator light turns
on and then turns
off after a few
seconds. If the TCS or DSC is
operating , the indicator light flashes.

If the light stays on, the TCS, DSC or
the brake assist system may have a
malfunction and they may not operate
correctly. Take your vehicle to an
Authorized Mazda Dealer.
When Driving
ABS/TCS/DSC
4-66
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Power Steering
▼Power Steering
Power steering is operable when the
power switch is switched ON (EV
system on). The steering wheel can
still be operated even when the
power switch is switched to a
position other than ON (EV system
on), however, the operation may feel
heavy compared to normal.
If the steering feels sti
ffer than usual
during normal driving or the steering
vibrates, consult an Authorized
Mazda Dealer.
The malfunction indication/indicator
light notifies the driver of system
abnormalities and operation
conditions.
Refer to Power Steering Malfunction
Indication/Indicator Light on page
7-25.
When Driving
Power Steering
4-67
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Front Camera/Side
Cameras/Rear Camera
*
▼ Front Camera/Side Cameras/Rear
Camera
Your vehicle is equipped with a front
camera, side cameras, and a rear
camera.
1. Side cameras
2. Front camera
3. Rear camera

Each camera is used by the following
system.
360°View Monitor
The front camera, side cameras, and
rear camera shoot images of the area
surrounding the vehicle.
Driver Monitoring Camera
*
▼Driver Monitoring Camera
Your vehicle is equipped with a driver
monitoring camera.
1. Driver monitoring camera

The driver monitoring camera is used
by the following system.
Driver Monitoring (DM)
The driver monitoring camera detects
changes in the driver's facial features
and estimates the amount of
accumulated fatigue and sleepiness of
the driver.
NOTE
DM and the earlier collision warning
may not operate normally under the
following conditions.
The driver monitoring camera is
covered with something.
You are driving the vehicle while
leaning on the steering wheel.
You are wearing glasses or
sunglasses.
A cap or hat you are wearing
partially blocks the driver
monitoring camera's view of your
eyes, you have long bangs partially
covering your eyes, or a part of
your face is invisible due to a face
mask.
When Driving
i-ACTIVSENSE
*Some models.4-81
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

The lighting conditions changesigni ficantly (such as backlight,
light from the side, or direct light
from the setting sun, and the
headlights of on-coming vehicles).
You are driving the vehicle with
your head excessively tilted to one
side or the other.
You are moving around extensively.Your face or your eyes frequently
turn in direction other than straight
ahead (direction of travel).
Your line of sight moves or directly
after it has moved.
There is a large di fference between
your line of sight and the direction
your face is pointed.
You are driving the vehicle with
your head largely tilted to one side.
Free/open source software
information
This product includes free/open
sources. Information about the
licensing and source code is
available at the following URL.
http://
www.embedded-carmultimedia.jp
/RTOS/License/oss/DMS_0201/
Adaptive Front Lighting
System (AFS)
*
▼Adaptive Front Lighting System
(AFS)
The adaptive front lighting system
(AFS) automatically adjusts the
headlight beams to the left or right in
conjunction with the operation of the
steering wheel after the headlights
have been turned on and the vehicle
speed is about 2 km/h (2 mph) or
higher.
A system malfunction or operation
conditions are indicated by a warning.
Refer to Exterior Light Warning
Indication/Warning Light on page
7-29.
NOTE
The Adaptive Front Lighting System
(AFS) can be switched to on/o
ff using
the personalization function.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When Driving
i-ACTIVSENSE
4-82*Some models.
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

▼Manual Switching
Switching to low beams
Switch the headlight switch to the
position, or press the high beam
control switch.
The HBC indicator light (green) turns
o
ff.
1. High beam control switch

If the HBC is turned o ff using the high
beam control switch, press the high
beam control switch again to turn the
HBC back on.
Switching to high beams
Shift the lever to the high beam
position.
The HBC indicator light (green) turns
o ff and the headlight high-beam
indicator light is illuminated.
Lane Departure Warning
System (LDWS)
*
▼Lane Departure Warning System
(LDWS)
The LDWS noti
fies the driver that the
vehicle might be deviating from its
lane.
The LDWS detects white (yellow) lines
using the Forward Sensing Camera
(FSC). If your vehicle may be deviating
from its lane, the lane departure
warning noti fies the driver.

Use the LDWS when you drive the
vehicle on roads with white (yellow)
lines.
WARNING
Do not rely completely on the LDWS
and always drive carefully:
 The LDWS is not designed to
compensate for a driver’s lack of
caution and relying too much on the
system could lead to an accident.
 The functions of the LDWS have
limitations. Always stay on course
using the steering wheel.
When Driving
i-ACTIVSENSE
4-84*Some models.
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07