ignition MAZDA MODEL RX 8 2004 (in English) Service Manual

5-40
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R65-EA-03C

ABS Warning Light
The warning light stays on for a few
seconds when the ignition switch is turned
to the ON position.
If the ABS warning light stays on while
you’re driving, the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function
normally as if the vehicle had no ABS.
Should this happen, consult an Authorized
Mazda Dealer as soon as possible.
Air Bag/Front Seat Belt
Pretensioner System Warning
Light
If the air bag/front seat belt pretensioner
system is OK, the warning light comes on
when the ignition switch is turned to the
ON position or after the engine is cranked.
After about 6 seconds it goes out.
A system malfunction is indicated when
the warning light constantly flashes, stays
on or doesn’t come on at all when the
ignition switch is turned to the ON
position. If any of these occur, consult an
Authorized Mazda Dealer as soon as
possible. The system may not work in an
accident.
ABS Warning Light and Brake
Warning Light on at the Same Time:
Driving when the brake system
warning light and ABS warning light
are on at the same time is dangerous.
When both lights are on, the rear
wheels could lock more quickly in an
emergency stop than under normal
circumstances.
Don’t drive with both lights on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
WARNING
NOTE
When the engine is jump-started to
charge the battery, uneven rpm occurs
and the ABS warning light comes on.
This is due to a weak battery, not a
malfunction.
Recharge the battery.
J60E_8R65-EA-03C_Edition2.book Page 40 Saturday, April 26, 2003 1:48 PM

5-41
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R65-EA-03C

Low Fuel Warning Light
This warning light in the fuel gauge
signals that the fuel tank will soon be
empty.
Refuel as soon as possible.

Seat Belt Warning Light
If the driver’s seat belt is not fastened
when the ignition switch is turned to the
ON position, the seat belt warning light
will remain on until the belt is fastened.
If the system does not operate correctly,
consult an Authorized Mazda Dealer.

Door-Ajar Warning Light
This warning light comes on when any
door isn’t securely closed.

Low Washer Fluid Level
Wa r n i n g L i g h t *
This warning light reveals that little
windshield washer fluid remains. Add
fluid (page 8-17).
Self-Servicing the Air Bag/
Pretensioner Systems:
Self-servicing or tampering with the
systems is dangerous. An air bag/
pretensioner could accidentally
activate or become disabled. This
could cause serious injuries. Never
tamper with the systems and always
have an Authorized Mazda Dealer
perform all servicing and repairs.
WARNING
Low fuel warning light
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 41 Saturday, April 26, 2003 1:48 PM

5-42
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R65-EA-03C

Automatic Transmission
Wa r n i n g L i g h t
This warning light stays on for a few
seconds when the ignition switch is turned
to the ON position.
The light illuminates when the
transmission has a problem.

Tire Pressure Monitoring System
Warning Light*
This warning light illuminates for a few
seconds when the ignition switch is turned
to the ON position.
Thereafter, the warning light illuminates
when tire pressure is too low or too high
in one or more tires, and flashes when
there is a system malfunction.Warning light illuminates/Warning
beep sounds
When the warning light illuminates, and
the warning beep sounds (about 3
seconds), tire pressure is too low or too
high in one or more tires.
Adjust the tire pressure to the correct tire
pressure at an Authorized Mazda Dealer
or the nearest service station. Refer to the
specification charts (page 10-7). If the automatic transmission warning
light illuminates, the transmission has
an electrical problem. Continuing to
drive your Mazda in this condition
could cause damage to your
transmission. Consult an Authorized
Mazda Dealer as soon as possible.
CAUTION
Vehicle Handling When Tire Pressure
Monitoring System Warning Light
Illuminates/Flashes:
When the tire pressure monitoring
system warning light illuminates or
flashes, or the tire pressure warning
beep sounds, it is dangerous to drive
the vehicle at high speeds, or perform
sudden maneuvering or braking.
Vehicle drivability could worsen and
result in an accident.
When the tire pressure monitoring
system warning light illuminates or
flashes, or the tire pressure warning
beep sounds, decrease vehicle speed
immediately and avoid sudden
maneuvering and braking. Have the
system and tires checked or perform
the appropriate repair as soon as
possible.
Ignoring the Warning Light:
Ignoring the warning light is
dangerous, even if you know why it is
illuminated. Have the problem taken
care of as soon as possible before it
develops into a more serious situation
that could lead to tire failure and a
dangerous accident.
WARNING
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 42 Saturday, April 26, 2003 1:48 PM

5-43
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R65-EA-03C
If the warning light illuminates again even
after the tire pressures are adjusted, there
may be a tire puncture.
Vehicles with Instant Mobility System
(IMS) emergency flat tire repair kit
If an emergency tire repair is needed,
repair the punctured tire with the
emergency flat tire repair kit (page 7-5).
Vehicles with optional temporary spare
tire
If you have bought the optional temporary
spare tire, replace the punctured tire with
the temporary spare tire . Refer to the
manufacturer’s instructions.
Warning light flashes
When the warning light flashes, there may
be a system malfunction. Consult an
Authorized Mazda Dealer.

Security Indicator Light
This indicator light starts flashing every
2 seconds when the ignition switch is
turned from the ON to the ACC position
and the immobilizer system is armed.
The light stops flashing when the ignition
switch is turned to the ON position with
the correct ignition key.
At this time, the immobilizer system is
disarmed and the light illuminates for
about 3 seconds and then goes out.
If the engine doesn’t start with the correct
ignition key, and the security indicator
light keeps illuminating or flashing, the
system may have a malfunction. Consult
an Authorized Mazda Dealer.

Headlight High-Beam Indicator
Light
This light indicates one of two things:
•The high-beam headlights are on.
•The turn signal lever is in the flash-to-
pass position. When replacing/repairing the tires or
wheels or both, have the work done by
an Authorized Mazda Dealer, or the
tire pressure sensors may be damaged.
Do not use non-genuine tire sealant. It
may damage the tire pressure sensor.
NOTE
A tire pressure sensor is not installed
to the temporary spare tire. The
warning light will flash continuously
while the temporary spare tire is being
used.
CAUTION
CAUTION
J60E_8R65-EA-03C_Edition2.book Page 43 Saturday, April 26, 2003 1:48 PM

5-44
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R65-EA-03C

Shift Position Indicator Light
(Automatic Transmission)
This indicates the selected shift position
when the ignition switch is in the ON
position.
In manual mode, the "M" of the shift
position indicator illuminates and the
numeral for the selected gear illuminates
in the gear position indicator.

TCS/DSC Indicator Light*
This indicator light stays on for a few
seconds when the ignition switch is turned
to the ON position. If the TCS or DSC is
operating, the indicator light flashes.
If the light stays on, the TCS or DSC may
have a malfunction and they may not
operate correctly. Take your vehicle to an
Authorized Mazda Dealer.

DSC OFF Indicator Light*
This indicator light stays on for a few
seconds when the ignition switch is turned
to the ON position.
It also comes on when the DSC OFF
switch is pressed and TCS/DSC is
switched off.
If the light stays on when the TCS/DSC is
not switched off, take your vehicle to an
Authorized Mazda Dealer. The dynamic
stability control may have a malfunction.
Gear position indicator
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 44 Saturday, April 26, 2003 1:48 PM

5-45
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R65-EA-03C

Cruise Main Indicator Light
This light comes on when the ON/OFF
switch is pressed and the cruise control
system is activated.

Cruise Set Indicator Light
This light comes on when a cruising speed
is set.

Light-On Indicator Light
This indicator light comes on when the
exterior lights are on.

Power Steering Malfunction
Indicator Light
This indicator light illuminates when the
ignition switch is turned to the ON
position and goes off when the engine is
started.
If this light illuminates while driving, it
indicates a malfunction of the power
steering system. Consult an Authorized
Mazda Dealer.
NOTE
If the battery is disconnected, the DSC
will be inoperable. In this case, the
DSC OFF indicator light flashes and
the TCS/DSC indicator light
illuminates.
To make the DSC operable, do the
following procedure.
1. Turn the ignition switch to the ON
position.
2. Turn the steering clockwise fully,
then turn it counterclockwise fully.
3. Make sure the DSC OFF indicator
goes off.
4. Turn the ignition switch to the OFF
position, then turn it to the ON
position again.
5. Make sure the TCS/DSC indicator
light goes off.
If the TCS/DSC indicator light and the
DSC OFF indicator light remain
illuminated even after turning the
ignition switch to the ON position,
consult an Authorized Mazda Dealer.
J60E_8R65-EA-03C_Edition2.book Page 45 Saturday, April 26, 2003 1:48 PM

5-46
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R65-EA-03C

Headlight Auto-Leveling
Malfunction Indicator Light*
This indicator light stays on far a few
seconds when the ignition switch is turned
to the ON position.
Thereafter, the indicator light will
illuminate when the headlight auto-
leveling system has a malfunction.
If the indicator light illuminates, contact
an Authorized Mazda Dealer.

Turn-Signal/Hazard Warning
Indicator Lights
When operating the turn-signal lights, the
left or right turn-signal indicator light
flashes to indicate which turn-signal light
is operating (page 5-50).
When operating the hazard warning
lights, both turn-signal indicator lights
flash (page 5-55).
NOTE
The power steering system is
inoperable when the malfunction
indicator light illuminates. Manual
steering is possible, but requires more
physical effort.
NOTE
If an indicator light remains
illuminated (does not flash) or if it
flashes abnormally, the turn signal bulb
may be burned out.
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 46 Saturday, April 26, 2003 1:48 PM

5-47
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R65-EA-03C

Seat Belt Warning Beep
If the driver’s seat belt is not fastened
when the ignition switch is turned to the
ON position, a beep will sound for about
6 seconds.

Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep will sound when the
driver’s door is opened.

Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when the driver’s door is opened.

Engine Overrev Warning Beep
The beep sounds to indicate engine
overrev when the tachometer needle
enters the striped zone (page 5-31).

Tire Inflation Pressure Warning
Beep*
The warning beep sounds for about 3
seconds when there is any abnormality in
tire inflation pressures.
(page 5-24)
Beeps
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 47 Saturday, April 26, 2003 1:48 PM

5-48
Driving Your Mazda
Form No. 8R65-EA-03C
Switches and Controls

Headlights
To turn on the lights, turn the headlight
switch on the end of the control lever.
Xenon fusion headlight bulbs*
The low-beam bulbs of the headlights
have xenon fusion bulbs that produce a
bright white beam over a wide area.

Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when the driver’s door is opened.

Headlight High-Low Beam
Push the lever forward for high beam.
Pull it back for low.
Lighting Control
Switch Position OFF
Headlights Off Off On
Taillights
Parking lights
License lights
Side-marker lightsOff On On
NOTE
To prevent discharging the battery,
don’t leave the lights on while the
engine is off.
Xenon Fusion Bulb Replacement:
Replacing the xenon fusion bulbs by
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Do not replace the xenon
fusion bulbs by yourself. Consult an
Authorized Mazda Dealer when the
replacement is necessary.
NOTE
If the headlights flash, or the
brightness weakens, the bulb-life may
be depleted and a replacement is
necessary. Consult an Authorized
Mazda Dealer.
WARNING
Low beamHigh beam
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 48 Saturday, April 26, 2003 1:48 PM

5-49
Driving Your Mazda
Switches and Controls
Form No. 8R65-EA-03C

Flashing the Headlights
To flash the headlights, pull the lever fully
toward you. The headlight switch need
not be on, and the lever will return to the
normal position when released.

Headlight Leveling*
The number of riders and weight of cargo
in the luggage compartment change the
angle of the headlights.
The angle of the headlights will be
automatically adjusted when turning on
the headlights.Headlight auto-leveling malfunction
indicator light
This indicator light stays on far a few
seconds when the ignition switch is turned
to the ON position.
Thereafter, the indicator light will
illuminate when the headlight auto-
leveling system has a malfunction.
If the indicator light illuminates, contact
an Authorized Mazda Dealer.

Daytime Running Lights
(Canada)
In Canada, vehicles must be driven with
the headlights on during daytime
operation.
For that reason, the daytime running lights
automatically turn on when the ignition
switch is turned to the ON position.
NOTE
The running lights go off when the
parking brake is applied.
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 49 Saturday, April 26, 2003 1:48 PM