height adjustment MAZDA MODEL RX 8 2009 Owners Manual (in English)

Black plate (16,1)
(Dial type)
To change the seatback angle, lean
forward slightly while rotating the dial to
the desired position.
(Lever type)
To change the seatback angle, lean
forward slightly while raising the lever.
Then lean back to the desired position and
release the lever.
Make sure the lever returns to its original
position and the seatback is locked in
place by attempting to push it forward and
backward.
CAUTION
When returning a rear-reclined
seatback to its upright position,
make sure you hold onto the
seatback with your other hand while
operating the lever or dial. If the
seatback is not supported, it will flip
forward suddenly and could cause
injury.
qHeight Adjustment (Driver's Seat)
By moving the seat lever up or down, the
seat bottom height can be adjusted.
Up
Down
2-4
Essential Safety Equipment
Seats
RX-8_8Z09-EA-08C_Edition3 Page16
Thursday, July 3 2008 2:22 PM
Form No.8Z09-EA-08C

Black plate (20,1)
qSeat Recline
WARNING
Do not drive with the seats reclined:
Sitting in a reclined position while the
vehicle is moving is dangerous
because you don't get the full
protection from seat belts. During
sudden braking or a collision, you
can slide under the lap belt and
suffer serious internal injuries. For
maximum protection, sit well back
and upright.
Always sit in a front passenger seat
properly with the seatback upright and
feet on the floor: If your vehicle is equipped with front
passenger seat weight sensors,
sitting in the front passenger seat
improperly out of position or with the
seatback reclined too far while the
vehicle is moving is dangerous as it
can take off weight from the seat
bottom and affect the weight
determination of the front passenger
sensing system. As a result the front
passenger will not have the
supplementary protection of the air
bag and seat belt pretensioner, which
could cause result in serious injury.
Always sit upright against your
seatback, with your feet on the floor. Change the seatback angle by pressing the
front or rear side of the reclining switch.
Release the switch at the desired position.
q
Height Adjustment
The seat height can be adjusted by
moving the switch up or down.
2-8
Essential Safety Equipment
Seats
RX-8_8Z09-EA-08C_Edition3 Page20
Thursday, July 3 2008 2:22 PM
Form No.8Z09-EA-08C

Black plate (21,1)
qSeat Position Memory
One-touch seat position programming and
a call up function are available on the
driver's seat.
CAUTION
When calling up the seat position, do
not place your hands or fingers
around the seat bottom. The seat
moves to the desired position
automatically, and if your hands or
fingers are placed around the seat
bottom, it could cause injury.
Set button
Programming of the driver's seat positions
is possible using the following functions:
lProgramming buttons―and the
set button. Programmed seat positions can also be
called up using the following functions:
lProgramming buttons―.
Operation using the seat-side buttons
Programming
Seat position programming is possible
when the vehicle is parked.
1. Adjust the seat to the desired position.
For each seat position adjustment
method refer to the following pages:
Seat Slide (page 2-7)
Seat Recline (page 2-8)
Height Adjustment (page 2-8)
2. Press the desired programming button
―while pressing the set button
until a beep sound is heard.
NOTE
Vehicle maintenance or other reasons
requiring the vehicle battery to be
disconnected will result in the seat position
memory being erased.
In this case, re-program the seat positions.
Seat position call up
While the vehicle is stopped, press and
hold a programming button
―for
the desired seat position.
When the seat is in the programmed
position, a beep sound is heard.
NOTE
If any of the following occurs, the seat position
call up function cancels:
lA seat adjustment switch other than a
lumbar support switch is operated.
lThe vehicle moves or starts to move.lThe selected programming button―
or the set button is pressed again.lThe set button is operated.
Essential Safety Equipment
Seats
2-9
RX-8_8Z09-EA-08C_Edition3 Page21
Thursday, July 3 2008 2:22 PM
Form No.8Z09-EA-08C