Oil MAZDA MX-5 1994 Workshop Manual

TRANSMISSION 1. Manual valve 12. Separator plate 2. Oil strainer 13. Orifice check valve 3. 3-2 control solenoid valve 14. Orifice check spring ................ ................ i/ Inspection page K- 42 Inspection page K-115 4. Oil strainer 15. Throttle relief ball 5. 1-2 shift solenoid valve 16. Throttle relief spring Inspection ................ page K- 42 Inspection ................ page K-115 6. Oil strainer 17. Valve body cover 7. 2-3 shift solenoid valve 18. Inner strainer Inspection ................ page K- 42 19. Separator plate 8. Oil strainer 20. Orifice check valve 9. 3-4 shift solenoid valve 21. Orifice shock spring ................ Inspection ................ page K- 42 Inspection page K-115 10. Oil strainer 22. Lower valve body 11. Upper valve body Disassembly / Inspection / ................ Disassembly / Inspection / Assembly page K-120 Assembly ............... page K-116 Disassembly procedure 1. Remove the 3-2 control solenoid valve. 2. Remove the oil strainer and O-ring. 3. Remove the 1-2 shift solenoid valve. 4. Remove the oil strainer and O-ring. I I 45UOKX425 5. Remove the 2-3 shift solenoid valve. 6. Remove the oil strainer and O-ring. i/ Gartner Banana

K TRANSMISSION 7. Remove the 34 shift solenoid valve. 8. Remove the oil strainer and O-ring. 9. Remove the bolts and nuts shown in the figure. 10. Hold the lower valve body and separator plate together with a large clip. 11. Remove the upper valve body. 12. Remove the clip. 13. Gently remove the separator plate. Note Tag the orifice check valves for proper reassembly. 14. Remove the orifice check valves, throttle relief ball, and springs. Gartner Banana

TRANSMISSION K r FREE LENGTH 1 -/i- WIRE DIAMETER 15. Gently remove the separator plate. Note Tag the orifice check valves for proper reassembly, 16. Remove the orifice check valves and springs. Inspection 1. Measure the spring specifications. 2. If not within specification, replace the spring(s). item Outer dia. Spring mm {in} Free length mm {in) 15.5 (0.61 0) 26.8 (1.055) Orifice check Throttle relief 5.0 (0.1 97) 6.5 I0.256) No. of coils 12.0 14.0 Wire dla. mm {in) 0.23 (0.009) 0.9 {0.035) Gartner Banana

TRANSMISSION 1. Bolts 16. 2-3 shift valve 2. Side plate 17. 2-3 shift spring 3. N-R reducing spring Inspection ................ page K-117 ................ w Inspection page K-117 18. Bolts 4. N-R reducing valve 19. Side plate 5. Pressure regulator sleeve 20. Vacuum throttle valve 6. Pressure regulator plug 21. 3-4 shift sleeve 7. Spring seat 22. 3-4 shift valve 8. Pressure regulator spring 23. 3-4 shift spring Inspection ................ page K-117 Inspection ................ page K-117 9. Pressure regulator valve 24. Backup control valve 10. Bolts 25. Backup control spring 11. Side plate Inspection ................ page K-117 12. Pressure modifier valve 26. Throttle backup spring ................ 13. Pressure modifier spring Inspection page K-117 Inspection ................ page K-117 27. Throttle backup valve 14. 1-2 shift valve 28. Manual valve 15. 1-2 shift spring 29. Upper valve body Inspection ................ page K-117 I t- FREE LENGTH 7 WIRE DIAMETER lnspection 1. Measure the spring specifications. 2. If not within specification, replace the spring(s). item Outer dia. mm (in) Pressure regulator 1-2 shift Free iength mm (in} 2-3 shift 3-4 shift 11.7 (0.461) 7.4 (0.291) Pressure modifier Throttle backup No. of coils 10.0 (0.394) 7.5 (0.295) I I I I Wire dia. mm (in} 43.0 (1.693) 26.4 (1.039) 9.2 (0.362) 9.0 (0.354) N-R reducing Backup control 50.0 (1 .969) 40.2 (1 583) 13.0 9.6 19.8 {0.780} 17.5 {0.689) 8.5 (0.335) 1.2 (0.047) 0.7 (0.028) 13.7 15.0 0.6 (0.024) 7.4 (0.291) 1 .O (0.039) 0.8 (0.031) 5.3 5.2 21.3 (0.639) 0.7 (0.028) 0.9 (0.035) 14.5 (0.571) 5.0 7.3 0.9 (0.035) Gartner Banana

TRANSMISSION K 1. Bolts 13. Side plate 2. Clip 14. N-R/2-3 accumulator piston 3. Side plate 15. N-R/2-3 accumulator spring ................ i/ 4. N-D accumulator piston Inspection page K-121 5. N-D accumulator spring 16. Seal ring Inspection ................ page K-121 17. 3-2 control spring 6. Seal ring Inspection ................ page K-121 7. Pin 18. 3-2 control valve 8. Stopper plug 19. 1-2 accumulator spring ................ 9. 1-2 reducing spring Inspection page K-121 Inspection ................ page K-121 20. 1-2 accumulator piston 10. 1-2 reducing valve 21. Seal ring 11. Bolts 22. Lower valve body 12. Clip i- FREE LENGTH 1 --k WIRE DIAMETER lnspection 1. Measure the spring specifications. 2. If not within specification, replace the spring(s). - 3-2 control Item Spring N-R/2-3 accumulator N-D accumulator 1-2 reducing Free length mm {in) 82.5 13.248) Outer dia. mm {in} 8.9 10.3501 9.3 {0.366) 9.4 10.370) 1-2 accumulator No. of coils 29.7 Wire dia. mm {in) 1.1 10.043) 43.4 {I .709) 19.5 {0.768) 11.2 I0.441) 22.0 5.0 62.0 (2.441) 1.4 I0.055) 0.8 {0.031) 21.3 1.2 (0.047) Gartner Banana

K TRANSMISSION 6. lnstall the separator plate. 7. lnstall the inner strainer in the valve body cover. 8. lnstall the valve body cover on the separator plate. 9. lnstall the bolts and nuts, referring to page K-124 for their correct sizes. Tighten the bolts and nuts to the spe- cified torque. Tightening torque: d Bolt: 6.5--7.8 N.m (66-80 kgfecm, 58-69 in-lbf) Nut: 10.8-14.7 Nem (11 0-150 kgf-cm, 95.5-1 30 in-lbf) 10. lnstall the O-rings onto each solenoid valve. 11. lnstall the oil strainer in the lower valve body. 12. lnstall the 3-2 control solenoid valve. 13. Tighten the installation bolt. Tightening torque: 2.5--3.4 N.m (25-35 kgf-cm, 22-30 in4bf) 14. lnstall the oil strainer in the lower valve body. 15. lnstall the 3-4 control solenoid valve. 16. Tighten the installation bolt. Tightening torque: 2.5--3.4 N-m (25--35 kgf-cm, 22-30 in-lbf) Gartner Banana

TRANSMISSION K 17. lnstall the oil strainer in the lower valve body. 18. lnstall the 2-3 control solenoid valve. 19. Tighten the installation bolt. Tightening torque: 2.5--3.4 N-m (2545 kgf-cm, 22--30 in4bf) 20. lnstall the oil strainer in the lower valve body. 21. lnstall the 1-2 control solenoid valve. 22. Tighten the installation bolt. Tightening torque: 2.54.4 N-m {25--35 kgf-cm, 22-30 inslbf) 23. Connect the ground terminals and install the bolts, refer- ring to page K-123 for the correct bolt sizes. 24. Tighten the bolt. Tightening torque: 6.5--7.8 N.m (66-80 kgf-cm, 58-69 in-lbf) 25. lnstall the oil strainer. 26. lnstall the bolts, referring to page K-123 for their correct sizes. Tightening torque: 6.5--7.8 N-m (66-80 kgf-cm, 58-69 in-lbf) 27. lnstall the manual valve. Gartner Banana

K TRANSMISSION On-vehicle Removal 1. Disconnect the negative battery cable. 2. On level ground, jack up the vehicle and support it evenly on safety stands. w 3. Remove the exhaust pipe. (Refer to page K-45.) Warning When the transmission and the ATF are hot, they can cause burns to the skin. Allow the transmis- sion and the ATF to cool before doing this proce- dure. 4. Loosen the oil pan installation bolts, and drain the ATF into a container. 5. Disconnect the vacuum hose. 6. Remove the vacuum diaphragm, O-rings, and vacuum diaphragm rod. 7. Remove the oil pan, and the gasket. 8. Disconnect the solenoid valve connector. 9. Remove the harness from the bracket. 10. Remove the control valve body assembly. Gartner Banana

TRANSMISSION K On-vehicle Installation 1. Set the valve body assembly in position, and align the manual plate and manual valve. Tightening torque: 10.8-1 4.7 N.m (11 0-150 kgf-m, 95.5--130 ftalbf) 2. Connect the solenoid valve connector. 3. Install the harness. , . 4. Install the oil pan along with a new gasket. MANUAL PLATE Tightening torque: 5.9-7.8 N.m (60-80 kgf-cm, 53-69 in4bf) 45UOKX-371 5. Install the bolts. Tightening torque: 5.9-7.8 Nsm (60--80 kgf-cm, 53--69 inalbf) 6. Apply ATF to a new O-ring and install it onto the vacuum diaphragm. 7. Apply ATF to a new O-ring and install it into the transmis- sion case. 8. Apply ATF to the vacuum diaphragm rod and vacuum di- aphragm, and install them into the transmission case. Tightening torque: 7.9-1 0.7 N-m (80-1 10 kgf-cm, 70-95.4 in-lbf) 9. Connect the vacuum hose. 10. Install the exhaust pipe. (Refer to page K-148.) 11. Add approximately 4.0 L (4.2 US qt, 3.5 Imp qt) ATF, and check the ATF level. (Refer to page K-35.) Gartner Banana

K TRANSMISSION VACUUM DIAPHRAGM Preparation SST Note Excessive shift shock and improper shifting often indicate a vacuum diaphragm malfunction. 49 GO32 355 Adjustment gauge Warning When the transmission and the ATF are hot, they can cause burns to the skin. Allow the trans- mission and the ATF to cool before doing this procedure. For adjustment of vacuum diaphragm rod On-vehicle Removal 1. On level ground, jack up the vehicle and support it evenly on safety stands. 2. Remove the exhaust pipe. (Refer to page K-45.) 3. Loosen the oil pan mounting bolts, and drain approx. 1.0 L (1.1 US qt, 0.9 Imp qt) of ATF. L' 4. Disconnect the vacuum hose. 5. Remove the vacuum diaphragm, O-rings, and vacuum diaphragm rod. Inspection 1. Check that the vacuum diaphragm rod moves when vac- uum is applied to the vacuum diaphragm. 2. If not correct, replace the vacuum diaphragm. Gartner Banana