lights MAZDA MX-5 1994 Owner's Guide

LIGHTING SYSTEM TNS RELAY Step 4 1. Disconnect the negative battery cable. 2. Remove the knee protector. 3. Disconnect the combination switch connector. 4. Check for continuity between the following terminals of the combination switch. m: Continuity 5. If not as specified, replace the combination switch. 6. If correct, repair the wiring harness. (TNS relay - combination switch) Removal 1 Installation Remove and install as shown in the figures. raillights Parking lights 3ide marker lights License plate lights Gartner Banana

T LIGHTING SYSTEM DAYTIME RUNNING LIGHTS (DRL) (CANADA SPEC.) Circuit Diagram '-2 - CANADA DAYTIME RUNNING LIGHTS (DRL) MAIN FUSE BLOCK I) MAIN \ \ /I IX-021 [X-031 FUSE BLOCK OFF WIPER \ If \ &E-1 1 OAL CONTROL UNIT I - IGNITION SWITCH xz U I LU 12 am2 z -wc YYU maw

LIGHTING SYSTEM T Symptom: Daytime running lights (DRL) do not illuminate. (Turn signals function normally.) DRL operate with engine running and following switches are off: Headlight switch Turn signal switch (Selected turn signal light flashes, other light remains illumi- nated) Hazard warning switch Parking brake switch (Parking brake released) Step 1 1. Position the vehicle on a flat surface and block the wheels to prevent vehicle movement. 2. Turn the ignition switch to ON. 3. Measure the voltage at the following terminal wires of the DRL control unit. 4. If correct, replace the DRL control unit. B+: Battery positive voltage Step 2 1. Disconnect the parking brake switch connector. 2. Check for continuity between the terminal of the switch and a body ground. Terminal J (L) u Connected to WIPER 20A fuse I(B) B (R) C (WIR) Parking brake lever Pulled one notch Continuity Yes Released Test condition Constant GND Parking brake switch Headlight switch No I 3. If not as specified, adjust or replace the parking brake switch. 4. If correct, repair wiring harness. (DRL control unit - Parking brake switch) Specification B+ Constant Parking brake released Headlight switch off Action Repair wiring harness (WIPER 20A - DRL control unit) Other B+ Other Repair wiring harness (DRL control unit - GND) Go to Step 2 Go to Step 3 Gartner Banana

T LIGHTING SYSTEM Step 3 1. Remove the column cover and disconnect the connec- tors of the headlight switch. 2. Check for continuity between the terminals of the head- Q light switch connector. Position I Terminal I I I I Headlight High beam I I 3. If not as specified, replace the combination switch. 4. If correct, repair wiring harness. (Headlight switch - DRL control unit) I Symptom: Daytime running lights (DRL) function does not cancel. OSUOTX-161 Headlight Low beam Step 1 1. Turn the ignition switch ON. 2. Verify the symptom by operating the following switches; the DRL should cancel. Go to the specified Step. Headlight switch. Hazard warning switch. Turn signal switch. Parking brake switch (lever pulled one notch). 0 1 0 0---0 : Continuity Symptom: DRL function not canceled when Headlight switch ON I Parking brake switch ON Step 5 I 05UOTX-163 Next Step Step 2 Hazard warning switch ON Turn signal switch ON Step 4 Step 4 4. If not as specified, go to Step 3. 5. If correct, replace the DRL control unit. Step 2 1. Turn on the ignition switch. 2. Turn on the headlight switch. 3. Check the voltage at the terminal wire C (WIR) of the DRL control unit connector. B+: Battery positive voltage J Terminal Voltage C (WIR) B+ Gartner Banana

T LIGHTING SYSTEM r REAR COMBINATION LIGHT Disassembly 1. Use a hot air blower to soften the "hot melt" (bonding Turn signal switch (in combination switch) Front turn signal lights agent) around the lens. Step 6 1. Disconnect the parking brake switch connector. 2. Check for continuity between the terminal of the switch and ground. u T-19 T-64 2. Remove the lens from the light rear of the lens with a hammer I Parking brake lever Pulled one notch Released 45U0TX-153 4. If correct, repair wirring harness. (Parking brake switch - DRL control unit) Removal 1 Installation Refer to the following pages: housing by pushing the handle or round bar. Continuity Yes No Item Headlight switch (in combination switch) Hazard warning switch 3. Remove the old hot melt from the light housing. 3. If not as specified, adjust or replace the parking brake switch. Reference page T-19 T-21 Gartner Banana

nia (i' [-I PACL LIGHT '-6 1.4k HEATER CDNTRCL CONTROL X3 SWITCH SWITCH ILLMI1UATIONS 1 -a? .ILLUMINATION LIGHTS WARNING I CRUISE CCNTQOL ILLVMINATION -0l PANEL LIGHT CONTROL SWITCH (I1 I 1-02 HEATER CONTROL SWITCH ILLGMINA~IONS (11 11-03 ASHTRAY ILLUMINATION (I) H-06 AT SELECT ILLUMINATION(II I -07 HAZARD WAWING AND RETRACTOFi SWITCH ILLUMINATION(II I-oz CRUISE CONTROL MAIN snITcn ILLWINATION (11 E-10 FRONT FOG LIGHT ANO REAR WIMOW DEFROSTER SUITCH ILLUMINATION (I) I Gartner Banana

1 mw GRIVER-SIDE AIR BAG MOOULE :-2 SWITCH [a-. .BACK-UP LIGHTS .HORN .STOPLIGHTS .HIGH-MOUNT STOPLIGHT 1 REAR COHeINATION LIGHT '-05 HORN (F) S-03 DRIVEA-SIDE AIR BAG mlDlhE (F) :-06 PASSENGER-SIDE AIR BAG WDULE (F) j-04 PASSENGER-SIDE AIR BAG WOULE (F) Gartner Banana

T AUDIO FEATURES 1. Antitheft System To deter audio unit theft, the system is designed to accept a code number that makes the audio unit inop- erable if it is removed from the vehicle and then reconnected without inputting the correct code number. 4 If the antitheft system is activated, the unit will not operate and a code will flash on the display until the correct code is entered. 2. Headrest Speaker Headrest speakers are available. 3. Preset Memory A total of 18 broadcasting stations on AM, FM1, and FM2 bands can be quickly and easily set. 4. Automatic Memory By using the automatic memory function, which is independent from the preset memory, station selec- tions can be easily made in an area where the broadcasting station frequencies are not known. 5. Clock The clock display is incorporated within the audio display. 6. Metal Tape Automatic Detection The tape player automatically detects the use of metal tape and makes internal adjustments for metal tape playback. The word "METAL" is shown on the display. 7. Display Lights The unit's display lights can be switched on or off as desired. 8. Bodysonic System In order for sufficient bass reproduction to be possible in a car audio system, a large-diameter woofer must be equipped. However, these woofers are space consuming. With the bodysonic system, the "bass ,, sensation" can still be felt, ever without a woofer. 9. Auto Level Controller (ALC) If the optimum bodysonic level is set when the car is stopped, the level will feel insufficient due to vehicle vibration when the car is running. The autolevel controller automatically adjusts the bodysonic level to . . the appropriate amount at any speed. 45UOTX-221 Gartner Banana

TECHNICAL DATA 1 Charge I 1.4 Belt 1.4 r. BODY ELECTRICAL SYSTEM 1 Air bag I 2 1 Retractor 1.4 Item Wattage (Bulb trade number) Hold Anti lock Wamlng and indicator lights 1.4 1.4 Washer Rear window defroster Beam Turn (LH and RH) Illumination Malfanction indicator Brake 1.4 1.4 I Exterior lights 3.4 3.4 3.4 x 4 1.4 1.4 Headlights Front turn signawparking lights Front side marker lights License plate lights Rear turn signal lights Rear side marker lights Stop/taillights Back-UP linhts High-mount stoplight I 18.4 (921) ACS 1 1.4 Hazard switch 1.4 60140 2718 (1 157 NA) 3.8 (1 94) 7.5 27 (1 1 56) 3.8 (1 94) 2718 {I 157) 27 (1 1561 Interior llahts - I lllumination lights I Cruise control main switch I 1.4 I 5 Ash tray U. HEATER AND AIR CONDITIONING SYSTEM I Item I Specit lcations I 3.4 Heater control switch ane el I 1.4 STANDARD BOLT AND NUT TIGHTENING TORQUE Refrigerant amount S (04 Compressor oil amount rnl {cc, fl oz) Refrigerant normal pressure MPa (kgflcm2, psi) 600 {2 1.21 130-1 70 {I 30-1 70,3.9-5.1) Low pressure: 0.154.25 (1 .5-2.5,21-361 Hiah Pressure: 1 37-1.57 (1 4--16, 199--228) Gartner Banana

PANEL REPLACEMENT V INSTALLATION a Apply body sealer before installing new parts as shown in the illustration. \- a After temporary installation of new parts, check the fit with associating parts (door, trunk lid, rear combination lights, rear bumper, rear finisher etc.). L To plug weld 2 points indicated by (A), first spot weld point (B) and turn down the flange of the rear deck panel to the original position. Gartner Banana