ESP MAZDA PROTEGE 1992 User Guide

F TROUBLESHOOTING GUIDE
8 ROUGH IDLE/ENGINE STALLS AT IDLE - ALWAYS
bESCRIP- l Engine starts normally but stalls or vibrates excessively at idle in every condition
‘ION TROUBLESHOOTING HINTS]
D Air/Fuel mixture too lean @ Incorrect idle speed
l Air leakage l Idle speed misadjustment l Fuel injection control malfunction l Idle speed control malfunction
*Low fuel line pressure @ One or more spark plugs not firing
3 One or more injectors clogged or not operating @ Low engine compression
3 Low intake air amount @ Airflow meter stuck INSPECTION
1
1
2
3
4
5
6
- Check if “00” is displayed on Self-Diagnosis
Checker with ignition switch ON w page F-82
SYSTEM2ELECT: 1
M v’SELECT SW: A TEST
Check if ECU terminal voltages are OK
MTX...Especially 2D, 20 and 2Q
ATX... Especially 2B, 2E and 3D CT page F-150
Disconnect high-tension lead at idle and check if
engine speed decreases equally at each cylinder
Check for injector operating sound at idle
Check if battery voltage exists at injector connec-
tor (W/R) wire
Check if strong blue spark is visible at discon-
nected high-tension lead
, Yes No Service Code No. displayed
Check for cause (Refer to specified
:heck sequence) “88” flashes
Check ECU terminal IF voltage CT page F-150
Specification: Battery voltage
(Ignition switch ON)
3 If OK, replace ECU w page F-149 3 If not OK, check wiring between
ECU and Self-Diaanosis Checker Yes
Go to next step No
Check for cause Yes
Go to Step 8 No
Go to next step
Go to Step 6
Go to Step 5 Yes
No
Yes
No
Yes
No I-
30 to next step w page F-83
0 page F-151
Check if injector resistance is OK c7 page F-131
Resistance: Approx. 12-l 852
c3 If OK, check wiring between ECU
and injector
c3 If not OK, replace injector w page F-131
Check wiring between ECU and injector
Go to next step
Check high-tension lead w page G-17
Q If OK, check distributor cap and
rotor w page G-22
c3 If not OK, replace high-tension lead
F-42

F TROUBLESHOOTING GUIDE
9
ROUGH IDLE/ENGINE STALLS AT IDLE - BEFORE WARM-UP
DESCRIP-
*Engine speed low or engine stalls or vibrates excessively at idle during warm-up
TION
[TROUBLESHOOTING HINTS]
@ Low intake air amount
@ Low fuel injection control
l Airflow meter stuck
*Fuel injection control malfunction
*Air cleaner element clogged
(Correction for coolant temperature)
*Air valve
@ Poor atomization
*Low RVP (summer) fuel used in cold weather
w page F-83
W: SELF TEST Check ECU terminal 1F voltage
w page F-150
Specification: Battery voltage
(Ignition switch ON)
c3 If OK, replace ECU c3 page F-149
* If not OK, check wiring between
ECU and Self-Diagnosis Checker
Vacuum: More than 450 mmHg (17.7 inHg)
AX.. Especially 2B, 2E and 30
w page F-150
NO Check for cause CT page F-181
5 Disconnect ISC valve connector and check if en-
Yes Go to next step
gine speed increases after warm-up
CT page F-l 18
No Replace ISC valve c3 page F-109
F-44

TROUBLESHOOTING GUIDE F
12 ROUGH IDLE/ENGINE STALLS JUST AFTER STARTING
DESCRIP-
*Engine starts normally but vibrates excessively or stalls just after starting (acceleration from idle) TION
*Idle conditions are normal in the other conditions [TROUBLESHOOTING HINTS]
@ Fuel injection control system or idle speed control sys-
@ Idle speed misadjustment
tern malfunction @ Ignition timing misadjustment
*Start signal not input to ECU iTEl
-s-- 3
4
5 INSPECTION
-T- ACTION
Check if “00” is displayed on Self-Diagnosis
Checker with ignition switch ON w page F-82
SYSTEM,SELECT: I
r -SELECT SW: A
Check if ECU terminal voltages are OK
MTX...Especially 1 N
ATX... Especially 1T w page F-150
Connect System Selector to diagnosis connector
and set Test Switch to “SELF TEST” and check
for correct ignition timing at idle after warm-up w page F-78
Ignition timing (BTDC)
l BP DOHC : 9”-11 o l BP SOHC : 4O--6O
l B8 : 60-80
Check continuity between throttle sensor termi-
nals IDL and E CT page F-159
MTX
Clearance between throttle
lever and stopper
MTX O.lmm (0.004 in)
1 .Omm (0.039 in)
ATX 0.1 mm (0.004 in)
0.6mm (0.024 in) Continuity
Yes
No
Yes
No
Try known good ECU and check if condition
mproves w page F-149 Yes
No
Yes
Go to next step No
Check for cause Yes
In same condition as Step 3 inspection
and apply parking brake
Check for correct idle speed w page F-80
Idle speed: 700-800 rpm
No
Adjust Yes
Go to next step No
Adjust Go to next step Service Code No. displayed
Check for cause (Refer to specified
check sequence) w page F-83
“88” flashes
Check ECU terminal IF voltage w page F-150
Specification: Battery voltage
(Ignition switch ON)
d If OK, replace ECU w page F-149
* If not OK, check wiring between
ECU and Self-Diagnosis Checker c7 page F-151
3 If OK, go to next step
3 If not OK, adjust idle speed w page F-80
w page F-79
w page F-159
F-49

TROUBLESHOOTING GUIDE F
iTEP INSPECTION ACTION
6 Connect System Selector to diagnosis connector Yes Go to next step
and set Test Switch to “SELF TEST” when en-
gine is cold
Check if engine speed decreases as engine
warms up
w page F-l 16
No Check air valve w page F-116
7
Disconnect ISC valve connector at idle and Yes Go to next step
check if idle speed increases
CT page F-l 16
No
Check ISC valve CT page F-l 16
8
Pinch PCV hose with pliers and check if engine Yes Check PCV valve
speed decreases w page F-136
Go to next step
9 Check if ECU terminal voltages are OK
Yes Try known good ECU and check if con-
MTX...Especially 20, 20 and 2Q
dition improves
ATX... Especially 28, 2E and 3D CT page F-149
CT page F-152 No Check for cause w page F-153
23UOFX-079
F-51

F TROUBLESHOOTING GUIDE
15
ENGINE STALLS ON DECELERATION
DESCRIP-
l Engine unexpectedly stops running while decelerating or after deceleration
TION l Idle condition normal
[TROUBLESHOOTING HINTS]
Engine speed drops too much when releasing accelerator or poor connector connection disconnected by deceleration
force
3 Idle speed control malfunction
3 Fuel cut control malfunction @ Idle speed misadjustment
TEP INSPECTION
ACTION
1
Check if idle condition is normal Yes
Go to next step
No Adjust or perform troubleshooting
Nos. 8-11 “ROUGH IDLE” v page F-42
F-48
--
2
Check if “00” is displayed on Self-Diagnosis Yes Go to next step
Checker with ignition switch ON
W page F-82 No
SYSTEM SELECT: 1 Service Code No. displayed
Check for cause (Refer to specified
check sequence) w page F-83
“88” flashes
Check ECU terminal IF voltage LIT= page F-150
Specification: Battery voltage
(Ignition switch ON)
W: SELF TEST + If OK, replace ECU w page F-149
Q If not OK, check wiring between
ECU and Self-Diagnosis Checker
3 Check switches for correct operation with Self-
Yes Go to next step
Diagnosis Checker Monitor Lamp with ignition
switch ON
w page F-105 No
Lamp not ON or OFF with specified
switch
Check for cause (Refer to specified
check sequence) CT page F-106
-,-y/
,’ Lamp always ON
Check wiring between ECU terminal 1 D
and Self-Diagnosis Checker
W: SELF
TEST
4 Check if ECU terminal voltages are OK
Yes Go to next step
MTX...Especially IV, 2D, 20, 2U, 2V and 2Q
ATX... Especially 28, 2E, 30, 3U, and 3V
w page F-150 No Check for cause w page F-151
5
Check for poor connection of following parts
Yes Repair or replace
. Ignition coil
l Igniter l Distributor
-- l High-tension lead
No l Injector Go to next step l Circuit opening relay l ECU
F-54

TROUBLESHOOTING GUIDE
16 ENGINE STALLS SUDDENLY (INTERMITTENT)
DESCRIP- l Engine intermittently stops running
TION l Before stalling, engine condition OK [TROUBLESHOOTING HINTS]
@ Intermittently no spark or no-fuel injection caused by ve-
hicle vibration, acceleration, or deceleration
*Poor connection in wire harness
3 INSPECTION
Check if “00” is displayed on Self-Diagnosis
Checker with ignition switch ON c7 page F-82
g
-%ELECT SW: A
Check for poor connection of following parts l ignition coil
l igniter l Distributor l High-tension lead l lniector
l Ci;cuit opening relay l ECU
Check if ECU terminal voltages are OK
MTX...Especially lB, 2A, 28 and 2C
ATX... Especially lB, 3A, 38 and 3C w page F-150
Note
l When checking voltages, tap, move, and
wiggle harness and connector to recreate
problem
Yes
No Service Code No. displayed
Check for cause (Refer to specified
check sequence) Note
l When checking wiring harness and
connectors, tap, move, and wiggle
suspect sensor and/or harness to
recreate problem
“88” flashes
Check ECU terminal IF voltage w page F-150
Specification: Battery voltage
(Ignition switch ON)
c3 If OK, replace ECU CT= page F-149
+ If not OK, check wiring between
ECU and Self-Diagnosis Checker
Yes
Repair or replace
No Go to next step
Yes
No
T ACTION
Go to next step w page F-83
Go to Troubleshooting No.2
‘CRANKS NORMALLY BUT WILL NOT
START (NO COMBUSTION)” CT- page F-30
Check for cause D page F-151
F-56

TROUBLESHOOTING GUIDE
17 HESITATES/STUMBLES ON ACCELERATION
bESCRIP-
*Flat spot occurs just after accelerator depressed or mild jerking occurs during acceleration
‘ION TROUBLESHOOTING HINTS]
0 Air/Fuel mixture becomes lean when depressing accelerator l Fuel injection control malfunction
(Correction for accelerating condition)
*Air leakage
l Fuel line pressure decreases l Spark advance control malfunction TEP INSPECTION ACTION
1 Check if “00” is displayed on Self-Diagnosis Yes Go to next step
Checker with ignition switch ON W page F-82 ’ No
Service Code No. displayed
SYSTEM SELECT: 1 Check for cause (Refer to specified
check sequence) w page F-83
“88” flashes
W: SELF TEST Check ECU terminal IF voltage CT= page F-150
Specification: Battery voltage
(Ignition switch ON) c3 If OK, replace ECU c? page F-149 * If not OK, check wiring between
ECU and Self-Diagnosis Checker Vacuum: More than 450 mmHg (17.7 InHg)
tern components
Replace air cleaner element 4
Check if ECU terminal voltages are OK
Yes Go to next step
MTX...Especiaily 2L
ATX... Especially lT, 2F, and 21 w page F-150
No Check for cause cp page F-151
5
Check if throttle linkage is correctly installed and
Yes Go to next step
operates freely w page F-l 14 ~~
Correct, clean, or replace as required
any binding or damaged linkage and
adjust cable deflection at throttle body w page F-l 14
6
Check continuity between throttle sensor termi- Yes Go to next step
nals IDL and E w page F-189
MTX
A-I-X 1
J E
IDL
Clearance between throttle
lever and stopper Continuity
MTX 0.1 mm (0.004 in) Yes
1 .Omm (0.039 in) No
ATX 0.1 mm (0.004 in)
Yes
0.6mm (0.024 in) No
No Adjust w page F-189
F-57

TROUBLESHOOTING GUIDE F
21 RUNS ROUGH ON DECELERATION/BACKFIRE
IESCRIP.
*Engine runs rough while decelerating and abnormal combustion occurs in exhaust system
MON l Transaxle in normal condition TROUBLESHOOTING HINTS]
1) Arr/Fuel mixture too rich
l Arr cleaner element clogged
l Fuel injection control malfunctron
(Fuel cut control)
l Injector fuel leakage
*Throttle sensor (IDL terminal) malfunction
l Dashpot malfunctron
er with ignition switch ON
Check ECU terminal 1F voltage w page F-150
Specification: Battery voltage
(Ignition switch ON)
+ If OK, replace ECU w page F-149 6 If not OK, check wiring between
ECU and Self-Diagnosis Checker
----~
Check for cause (Refer to specified
check sequence) w page F-106
SELECT SW: A Vacuum: More than 450 mmHg (17.7 inHg)
tern components
4 Check if air cleaner element is clean Yes
Go to next step w page F-79
No
Replace air cleaner element
5 Check if ECU terminal voltages are OK
Yes Go to next step
MTX...Especially lN, 2A, 2U and 2V
ATX... Especially lT, 3A, 3U and 3V CT page F-150
No Check for cause c=i‘ page F-151
F-69

EVAPORATIVE EMISSION CONTROL SYSTEM t
EVAPORATIVE EMISSION CONTROL SYSTEM
DESCRIPTION
/ /
ENGINE ENGINE
CONTROL CONTROL - INPUT - INPUT
UNIT UNIT
- -
SOLENOID VALVE SOLENOID VALVE k k / /
CHECK VALVE CHECK VALVE
(TWO-WAY) (TWO-WAY)
CHARCOAL CHARCOAL
CANISTER CANISTER
CHECK-AND-CUTC CHECK-AND-CUTC
VALVE VALVE
SEPARATOR SEPARATOR TO ENGINE TO ENGINE SIGNALS
The evaporative emission control system consists of the separator, the check-and-cut valve, the two-way
check valve, the charcoal canister, the purge control solenoid valve, the engine control unit (ECU), and the
input devices. The amount of evaporative fumes introduced into the engine and burned is controlled by the
solenoid valve to correspond to the engine’s operating conditions. To maintain best engine performance,
the solenoid valve is controlled by the ECU.
Operation
.._ The solenoid valve (purge control) is controlled by duty signals from the ECU to perform purging of the char-
coal canister. Purging is done when these conditions are met:
(1) After warm-up
(2) Driving in gear
(3) Accelerator pedal depressed (idle switch OFF)
(4) Oxygen sensor functioning normally
F-l 39

N
STEERING SYSTEM
INDEX ......................................................
MANUAL STEERING ............................... ;I g
ENGINE SPEED SENSING POWER
STEERING (ESPS) ................................. N- 3
OUTLINE ..................................................
SPECIFICATIONS .................................... ;I ::
MANUAL STEERING ..................................
PREPARATION ....................................... ;I ;
TROUBLESHOOTING GUIDE.. .................. N- 5
BOOT ................................................... N- 6
STEERING WHEEL AND COLUMN.. .......... N- 6
STEERING GEAR AND LINKAGE .............. N-13
ENGINE SPEED SENSING POWER
STEERING .............................................. N-23
PREPARATION ....................................... N-23
TROUBLESHOOTING GUIDE.. .................. N-25
AIR BLEEDING ....................................... N-26
STEERING WHEEL AND COLUMN.. .......... N-26
POWER STEERING FLUID.. ...................... N-27
STEERING GEAR AND LINKAGE .............. N-30
POWER STEERING OIL PUMP.. ................ N-37
DRIVE BELT ........................................... N-41
23UONX-001