button MERCEDES-BENZ C-Class 2005 W203 Comand Manual

73 Telephone*
Important notes

The message
Telephone being ac-
tivated, please wait
appears.
COMAND prepares the telephone for
use. Select other system functions, e.g.
radio, by pressing the corresponding
button or wait until the telephone is ac-
tive.

The message
Phone
not inserted

appears.

Please connect the mobile phone.

The message
Phone not available

appears.

Please contact an authorized
Mercedes-Benz Center.GSM mobile phone

If the message
Please insert SIM
card (Emergency Call 911 only
possible with phone)
appears:

Insert the SIM card into the mobile
phone (Telephone Operating
Manual).

The message
Call failed
may
appear if you place an outgoing call
(
page 81).

Try again later.

89 Telephone*
Telephone operation
You can select the following functions:
Changing the phone book display at
the COMAND

Selecting a phone book entry and
dialing the number (
page 89)
Changing the phone book display

Open the phone book (
page 88).

Press the
123
soft key.
The display changes to numbers. The
status bar displays the name of the
marked entry.
or

Press the
ABC
soft key.
The display changes to names. The
status bar displays the number of the
marked entry.Selecting a phone book entry and dia-
ling the number

Open the phone book (
page 88).
The list of phone book entries with
names starting with a certain letter is
displayed.
Changing the initial letters

Push the joystick to H or h one or
several times.
With every push of the button the
display changes to the next possible
letter. At the end of the letter list
follows the category
Others
.Category
Others
:
Here, all entries without names or with
names starting with a special character
(e.g. * or #) are put together.
Selecting an entry

Change the initial letter if required.

Push the joystick to G or g to
select a list entry.

Press the
Detail
soft key to see all
information about the entry.
iIf you hold one of the buttons, scrolling
is accelerated.

92 NavigationImportant notes

Important notesWarning
G
For safety reasons, you should only enter a
destination when the vehicle is stationary.
When the vehicle is in motion, a passenger
should enter the destination. Study manual
and select route before driving.
Do not watch display screen or operate but-
tons while the vehicle is in motion - let voice
instructions guide you. Stop at a safe locati-
on before using buttons or making correc-
tions.
Traffic regulations always have priority over
any route recommendations given.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your car is co-
vering a distance of 44 feet (approximately
14 m) every second.
The route calculated by COMAND is a re-
commendation on how to best reach your
selected destination.
During route guidance, you will not receive
any information on
Traffic lights

Stop and yield signs

Parking or stopping zones

One-way streets

Narrow bridges

Similar traffic regulation data
You should therefore always strictly observe
traffic regulations while driving. Drive care-
fully and always obey traffic laws and road
signs even if they contradict COMAND in-
structions.
Warning
G
The Navigation DVD module contains a
Class 1 laser product. There is a danger of
invisible laser radiation if the cover is ope-
ned or damaged.
Do not remove the cover. The Navigation
DVD module does not contain any parts ser-
viceable by the user. For safety reasons,
have any necessary service work performed
by qualified personnel.
The display unit can cause injury if contac-
ted when open. Return the display unit after
inserting a Navigation DVD to its closed
position (
page 147).

93 Navigation
Important notes
COMAND calculates the route with the
help of data that is stored on the navigati-
on DVD.
Only use Mercedes-Benz navigation DVDs.
Using other navigation DVDs or CDs will
cause malfunctions and/or damage.
Because of changes in local traffic patterns
(e.g. road works) and/or incomplete data,
errors in calculation may occur.
As a result, the recommended route may
deviate from the ideal route. The data
stored on the DVD only reflects local con-
ditions at the time of DVD production. DVD
maps do not cover all areas nor all routes
within an area. Loading/ejecting a DVD
DVDs are loaded and ejected at the DVD
Navigation slot. The DVD Navigation slot is
located behind the display unit.

Open the display unit to get access to
the DVD Navigation slot as described in
“Starting an update” (
page 148).
Navigation DVD
!GPS (G
lobal P
ositioning S
ystem) sig-
nals received make it possible to deter-
mine the current vehicle position.
Deviations from the actual position
may occur

if the reception of GPS signals is
disturbed e.g. in parking garages
and tunnels

if road conditions are bad

depending on the vehicle’s conditi-
on
iThere are two l buttons. One is on
the display unit. The other is located
left of the DVD NAVIGATION slot
behind the display (
page 147).

99 Navigation
Navigation main menu

Press c.
The full view of the map appears. You
will see the vehicle’s current position.

Press any soft key.
The soft key displays will appear.

Press the
Memory
soft key.
The system saves the current position
as a destination in the
Last
destinations
memory
(
page 134).
Saving current locationiIf route guidance is not active and the
Navigation main menu was displayed
last, you need to press the button
twice.
iSuch destinations are marked in
the
Last destinations
memory
with _.
For permanent storage you can save
the destination in the regular
Destination memory (
page 135).

112 NavigationDestination input
Push the joystick to H, h, g, G
to move the cross-hairs.

Push the joystick to F or f to move
the cross-hairs diagonally.This allows you to select your destination.

Release the button.
If the system is able to assign a street
name to the selected location, it is
displayed on the status bar.

Press E.
The system uses the point at the center
of the cross-hairs as destination.
The Start route guidance menu will
appear (
page 115).
iIf you press the
Back
soft key, your
selection will be discarded. The system
then uses the data of the previous
destination.
iIf a POI is close to the center of the
cross-hairs, a selection list will appear.
You can now select between a POI and
the address destination.

119 Navigation
Route guidance
Altering the map scale
The current map scale is indicated on the
left side of the status bar.
Press the + or ) soft key.
The map section is zoomed in or
zoomed out. A bar indicating the map
scale appears on the status bar.
Selecting map orientation
A symbol is shown on the bottom left side
of the status bar.

Heading Up
<:
Dynamic map alignment, map is
displayed facing driving direction
pointing up
or

North Up
Y:
Map is displayed facing northYou can select the map orientation
(
page 130).
Changing the map display
While route guidance is active, you can
switch between split view and full view.

Split view:
The map is shown on the left side and
information on the next maneuver on
the right.
or

Full view:
Full view of the map.

Press c.
The display changes with every push of
the button.When you reach the destination, you will
see the destination flag. Route guidance
ends.
iIf GPS display (
page 130) is active,
information on your current position is
shown on the status bar.
Arriving at destination

131 Navigation
During route guidance

In the Settings menu (
page 128),
press the
GPS
soft key.
The options On
and
Off
are displayed.
The symbol _ indicates the present
setting.

Use the joystick to g or G to select
the option with the symbol -.

Press button E.
Depending on the previous setting, the
GPS is switched on or off.

Press the
Back
soft key to confirm and
return to the map.
Automatic map toggling
You can set the change from map to split
view.

In the Settings menu (
page 128),
press the
Automap
soft key.
The available options are displayed.
You can select the following options:

AutomaticThe system automatically switches to
split view whenever it announces a
driving maneuver.
When the driving maneuver is
completed, the system reverts to the
full view.
i
Map
Shows the full screen as a map.

Split screen
Uses the right hand part of the
screen to show maneuver icons
and/or intersection zooms.

132 NavigationDuring route guidance
ManualIf you choose this option, the system
only switches to split screen by
pressing c.
The symbol _ indicates the present
setting.

Move the E joystick in g or G
direction to select the option with the
symbol -.

Press button E.
The option is changed.

Press the
Back
soft key to confirm and
return to the map.Trail settings
With this function is active, the COMAND
records a trail every time the vehicle is in
an OFF ROAD area (more than 0.25 miles
away from a digitized road).
The system places trail dots on the screen
until it matches to a digitized road again.

In the Settings menu (
page 128),
press the
Trail
soft key.
The options
On
and
Off
are displayed.
1Percentage of used memoryThe symbol _ indicates the present
setting.

Move the E joystick in g or G
direction to select the option with the
symbol -.

Press E.
Depending on the previous setting, the
Trail is switched on or off.

Press the
Back
s o f t k e y t o c o n f i rm a nd
return to the map.
Delete a trail
If there is a trail in memory, you can delete
it.

Press the
Clear
soft key.
The message
Are you sure you
want to clear all trails?
will
appear in a window.

136 NavigationLast destinations and destination memoryCreate a new name
Push the joystick to h, H, g or
G to select the characters. After each
selection, press E.

Push the joystick to F or f to
select characters diagonally.

Press E to confirm the entry.
The message
The address has
been saved as
will appear.
After that, the Start route guidance
menu, the
Last destinations

memory or the Today’s plan memory
reappear.Activating the destination memory

Activate the Navigation main menu
(page 96).

Push the joystick to g or G to
select menu item
Destination
memory
.

Press E.
The destination memory will appear.
The destination memory is sorted in
alphabetical order.Selecting a destination from the
destination memory
Activating the listing for the desired letter

Activate the destination memory.

Push the joystick to H or h until the
listing for the desired letter appears.
With every push of the joystick the
display changes to the next possible
letter.
or

Press 2 to 9 of the 12-button
keypad. Press a key once or several
times in quick succession until the
listing for the desired letter appears.iE.g.: Key 5
Press 1 x = access to listing for letter J
Press 2 x = access to listing for letter K
Press 3 x = access to listing for letter L