ignition MERCEDES-BENZ C-CLASS COUPE 2015 Workshop Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2015, Model line: C-CLASS COUPE, Model: MERCEDES-BENZ C-CLASS COUPE 2015Pages: 385, PDF Size: 13.12 MB
Page 156 of 385
Problems with the engine
Problem
Possible causes/consequences and
M
MSolutions The engine does not
start. The HOLD function or DISTRONIC PLUS is activated.
X Deactivat ethe HOLD function (Y page 192) or DISTRONIC PLUS
(Y page 184).
X Try to start the engine again (Y page 147).The engine does not
start. The starter motor
can be heard. R
There is amalfunction in the engine electronics.
R There is amalfunction in the fuel supply.
Before attempting to start the engine again:
X Turn the key back to position 0in the ignition lock.
or X Press the Start/Stop button repeatedly until all indicator lamps in
the instrumen tcluster go out.
X Try to start the engine again (Y page 147). Avoid excessively long
and frequent attemptstos tart the engine, as this will drain the
battery.
If the engine does not start after several attempts:
X Consult aqualified specialist workshop. The engine does not
start. The starter motor
can be heard. The
reserve fuel warning
lamp is lit and the fuel
gauge display is at the
reserve level. The fuel tank is empty.
X Refuel the vehicle. The engine does not
start. You cannot hear
the starter motor. The on-board voltage is too low because the battery is too weak or
discharged.
X Jump-start the vehicle (Y page 345).
If the engine does not start despite attemptstoj ump-start it:
X Consult aqualified specialist workshop. The starter motor was exposed to
athermal load that was too high.
X Try to start the engine again (Y page 147).
If the engine still does not start:
X Consult aqualified specialist workshop. Vehicles with
apetrol
engine:
The engine is not running
smoothly and is misfir-
ing. There is
amalfunction in the engine electronics or in amechanical
componen tofthe engine management system.
X Only depress the accelerator pedal slightly.
Otherwise, non-combusted fuel may get into the catalytic converter
and damage it.
X Have the cause rectified immediately at aqualified specialist work-
shop. Driving
153Driving and parking Z
Page 157 of 385
Problem
Possible causes/consequences and
M
MSolutions The coolant temperature
display is showing more
than 120 †. Adisplay
message may also
appear in the multifunc-
tion display and awarn-
ing tone may sound. The coolant level is too low. The coolant is too hot and the engine is no
longer being cooled sufficiently.
X Stop as soon as possible and allow the engine and the coolant to
cool down.
X Check the coolant level (Y page 324). Observe the warning notes
as you do so and top up the coolant if necessary. If the coolant level is correct,t
he engine radiator fan may be faulty. The
coolant is too hot and the engine is no longer being cooled sufficiently.
X If the coolant temperature is below 120 †, you can continue driving
to the nearest qualified specialist workshop.
X Avoid heavy loads on the engine as you do so, e.g. driving in moun-
tainous terrain and stop-start traffic. DYNAMIC SELECTs
witchAll vehicles(
except Mercedes-AMG
vehicles)
Use the DYNAMIC SELECT switch to change the
drive program. Depending on the drive program
selected, the following vehicle characteristics
will change:
R the drive (engine and transmission manage-
ment)
R the suspension
R the steering
R the availability of the ECO start/stop function
R the climate control
- the climate control settings
- the rear window heating operation period
- the performance of the seat heating
If the ignition is switched off for less than four
hours, the previously selected drive program is
activated when the engine is next started. If the ignition is switched off for more than four hours,
drive program Cis activated when the engine is
next started. :
DYNAMIC SELECT switch (example)
X Push DYNAMIC SELECT switch :forward or
back until the desired drive program is selec- ted.
The status icon of the selected drive program
is shown in the multifunction display.
In addition, the current drive program settings are displayed briefly in the display of the mul-
timedia system.
i In
af ew countries, the ECO start/stop func-
tion is deactivated at the factory due to the
quality of the available fuel. In this case, the
ECO start/stop function is not available in any
drive program, regardless of the display in the
multimedia system display.
Available drive programs: I
Individual Individual settings
S+
Sport Plus Particularly sporty driving
characteristics S
Sport Sporty driving characteris-
tics154
DYNAMIC SELECT switchDriving and parking
Page 158 of 385
C
Comfort Comfortable and economi-
cal driving characteristics
E
Economy Particularly economical
driving characteristics Additional informatio
nfor driv eprogram sfor:
R vehicle swithm anual transmission
(Y page 157)
R vehicle switha utomatic transmission
(Y page 161)
Vehicles with automatic transmission: you
can also chang egear yourself usin gthe steering
wheel gearshif tpaddles. Further informatio non
th em anual driv eprogram (Y page 163). Mercedes-AM
Gvehicles
General notes Select th
edrivep rogram usin gthe DYNAMIC
SELECT switch.
Availabl edrive programs: RACE
(S‑MODEL)
Drivin
gcharacteristic ssuit-
able for th eracetrack S+
Sport Plus Particularly sporty driving
characteristics
S
Sport Sport
ydriving characteris-
tics C
Comfort Comfortable and economi-
cal driving characteristics
I
Individual Individual settings
Dependin
gonthedriv eprogram selected, the
followin gvehicle characteristic swill change:
R thed rive( engin emanagement)
R thet ransmission management
R ESP ®
R thes uspension
R thep ositio noftheexhaust flap
R thes teering
R thea vailabilit yoftheECO start/sto pfunction
R thed river assistance systems
R thea vailabilit yofglidingmode
Further informatio nfor automatic driv eprogram
characteristic s(Ypage 161). Additionally, in driv
eprogram Iyou can config-
ure th erespectiv evehicle characteristic susing
th em ultimedia system. You can fin dinforma-
tio na bout this in th eDigital Owner' sManual.
If th eignition is switched off for less than four
hours, th epreviously selected driv eprogram is
activated when th eengineisn exts tarted. If the
ignition is switched off for mor ethanfour hours,
driv eprogram Cis activated when th eengineis
next started.
Selecting th edrive program X
Press DYNAMIC SELECT switch :forwards
or backwards until th edesired driv eprogram
is selected.
The status ico noftheselected driv eprogram
is shown in th emultifunction display.
In addition ,the curren tdriv ep rogram settings
are displayed briefly in th edisplay of th emul-
timedia system.
You can also chang egear yourself usin gthe
steering wheel gearshif tpaddles. Further infor-
mation on th emanual driv eprogram
(Y page 163). DYNAMIC SELECT switch
155Driving and parking Z
Page 162 of 385
Children could also set th
evehicle in motion,
for example by:
R releasin gthe parking brake
R shiftin gthe automatic transmission out of
park position P
R starting th eengine.
Ther eisar iskofana ccidentand injury.
When leaving th evehicle ,always tak ethe key
wit hyou and loc kthe vehicle .Never leave
children unattende dinthevehicle .Always
keep th ekeyout of reac hofchildren.
X If th etransmission is in position Dor R:p ush
th eD IRECT SELECT leve rupordown to the
first poin tofresistance.
X If th etransmission is in position P:depress
th eb rak epedal and push th eDIRECT SELECT
leve rupord own to th efirst poin tofresist-
ance.
If you switch th eengineo ff wit hthe transmis-
sion in position Ror D,t heautomatic transmis-
sion shifts to Nautomatically.
Wit hthe key: if you then open th edriver' sdoor
or th efront-pa ssenger door or remove th ekey
from th eignition ,the automatic transmission
shifts to Pautomatically.
Wit hthe Start/Stop button: if you then open
th ed river' sdoor or th efront-pa ssenger door,
th ea utomatic transmission shifts to Pautomat-
ically.
If you want th eautomatic transmission to
remain in neutral N,e.g.w hen having th evehicle
cleane dinana utomatic car wash wit hatowing
system:
X Vehicles with th
eStart-Sto pbutton:
remove th eStart-Sto pbutto nfromt heigni-
tio nlock.
X Inser tthe keyintot he ignition lock.
X All vehicles: switch theignition on.
X Depress th ebrak epedal and keep it
depressed.
X Shift to neutral N.
X Release th ebrak epedal.
X Release th eelectric parking brake.
X Switch off th eignition and leave th ekeyin the
ignition lock. Engaging drive position D X
If th etransmission is in position Ror N:p ush
th eD IRECT SELECT leve rdown past th efirst
poin tofr esistance.
X If th etransmission is in position P:depress
th eb rak epedal and push th eDIRECT SELECT
leve rdown past th efirst poin tofresistance. Transmission position and drive pro-
gram display
The curren ttransmission positio nand driv epro-
gram appear in th emultifunction display. :
Status icon, driv eprogram
; Transmissio nposition
= Gear
The arrows in th etransmission positio ndisplay
sho whow and int owhichtransmission positions
you can shif tusin gthe DIRECT SELECT lever.
If th etransmission positio ndisplay in th emul-
tifunctio ndisplay is no tworking ,you should pull
away carefull ytoc heck whether th edesired
transmission positio nisengaged .For this pur-
pose ,wer ecommen dselecting transmission
position Dand driv eprogram E(drive program C
in Mercedes-AM Gvehicles) or S. Automatic transmission
159Driving and parking Z
Page 170 of 385
If you mix dieself
uel with petrol, the flash
point of this fuel mixture is lowert han that of
pure dieself uel. When the engine is running,
components in the exhaust system may over-
heat unnoticed. There is arisk of fire.
Never refuel with petrol. Never add petrol to
dieself uel.
! Do not use dieseltor
efuel vehicleswith a
petrol engine. Do not switch on the ignition if you accidentally refuel with the wrong fuel.
Otherwise ,the fuel wille nter the fuel system.
Even small amounts of the wrong fuel can
resultind amage to the fuel system and the
engine. Notify aqualifieds pecialist workshop
and have the fuel tank and fuel lines drained
completely.
! Do not use petrol to refuel vehicle
swith a
diesele ngine. Do not switch on the ignition if
you accidentally refuel with the wrong fuel.
Otherwise ,fuel can enter the fuel system.
Even small amounts of the wrong fuel could
resultind amage to the fuel system and the
engine. The repairc osts are high. Notify a
qualifieds pecialist workshop and have the
fuel tank and fuel lines drained completely.
! Overfilling the fuel tank could damage the
fuel system.
! Take care not to spilla
ny fuel on painted
surfaces .You could otherwise damage the
paintwork.
! Use
afilter when adding fuel from afuel can.
The fuel lines and/or the fuel injection system could otherwise be blocked by particle sfrom
the fuel can.
If you overfill the fuel tank, some fuel may spray
out when you remove the fuel pump nozzle.
Further information on fuel and fuel quality
(Y page 371). Refuelling
General notes Observe the important safety notes
(Y
page 166).
If you unlock/lock the vehicle from the outside,
the fuel fillerf lap also unlocks/locks. The positio
nofthe8 fuel fillerc ap is dis-
played in the instrument cluster. The arrow next to the filling pump indicates the side of the vehi-
cle.
Openin gthe fuel fillerf lap :
To open the fuel fillerf lap
; To insert the fuel fillerc ap
= Tyre pressure table
? Instruction label on the fuel type to be refu-
elled
X Switch off the engine.
X Remove the key from the ignition lock.
or, on vehicle swith KEYLESS-GO start function
or KEYLESS‑GO:
X Open the driver's door.
The on-board electronics now have status 0.
This is the same as the key having been
removed.
X Press the fuel fillerf lap in the direction of
arrow :.
The fuel fillerf lap swings up.
X Turn the fuel fillerc ap anti-clockwise and
remove it.
X Insert the fuel fillerc ap into the holderont he
inside of fuel fillerf lap;.
X Completely insert the fillern eck of the fuel
pump nozzle into the tank, hook in place and refuel.
X Only fill the tank until the pump nozzle
switches off.
Do not add any more fuel after the pump stops
filling for the first time. Otherwise ,fuel may leak
out.
Vehicle swithadiese lengine: the fillern eck is
designed for refuelling at dieself illing pumps. Refuelling
167Driving and parking Z
Page 172 of 385
Problems with the fuel and fuel tank
Problem
Possible causes/consequences and
M
MSolutions Fuel is leaking from the
vehicle.
G
WARNING
The fuel line or the fuel tank is faulty.
There is arisk of fire or explosion.
X Apply the electric parking brake.
X Switch off the engine.
X Remove the key from the ignition lock.
or, on vehicles with KEYLESS-GO start function or KEYLESS ‑GO:
X Open the driver's door.
The on-board electronics now have status 0.This is the same as the
key having been removed.
X Do not restart the engine under any circumstances.
X Consult aqualified specialist workshop. The engine does not
start. The fuel tank of
avehicle with adiesel engine has been run completely
dry.
X Refuel the vehicle with at least 5litres of diesel.
X Turn the ignition on for approximately ten seconds (Y page 145).
X Start the engine continuously for amaximum of ten seconds until it
runs smoothly.
If the engine does not start: X Turn the ignition on again for amaximum of ten seconds
(Y page 145).
X Start the engine again continuously for amaximum of ten seconds
until it runs smoothly.
If the engine does not start after three attempts:
X Consult aqualified specialist workshop. The fuel filler flap cannot
be opened. The fuel filler flap is not unlocked.
X Unlock the vehicle (Y page 81). The key battery is discharged or nearly discharged.
X Unlock the vehicle using the emergency key element (Y page 82).The fuel filler flap is unlocked, but the opening mechanism is jammed.
X Consult aqualified specialist workshop. AdBlue
®
(BlueTEC vehicleso nly)
General notes To function properly, BlueTEC exhaust gas after-
treatmen tmust be operated with the reducing
agent AdBlue ®
. On vehicles with an 8.5
lAdBlue ®
tank ,topping
up AdBlue ®
is not part of the maintenanc ework.
Under normal operatin gconditions, afull tank of
AdBlue ®
should last until the nex tservic edue
date.
When the supply of AdBlue ®
is down to approx-
imately 3.0 litres, the Refill AdBlue See Refill AdBlue See Refuelling
169Driving and parking Z
Page 173 of 385
Owner’s Manual
Owner’s Manual
message is shown in the mul-
tifunction display.
If you drive the vehicle faster than 15 km/h after
topping up, the Refill RefillAdBlue
AdBlueSee
SeeOwner’s
Owner’s
Manual
Manual message goes out after approximately
one minute.
When the AdBlue ®
supplyd rops toaminimum,
the Refill AdBlue No start in ... mi
Refill AdBlue No start in ... mi
message is shown in the multifunction display.
When the Refill
Refill AdBlue AdBlueNo
Nostart
start in
in...
...
mi
mi message is shown in the multifunction dis-
play,y ou can still drive the vehicle over the dis-
tance shown. If the AdBlue ®
is not topped up,
you will subsequently be unable to start the
engine.Ift heRefill AdBlue Start not
Refill AdBlue Start not
possible
possible message appears in the multifunction
displaya nd the engine does not start, you must
top up AdBlue ®
.
X Add at least 3.5 lofAdBlue ®
.
X Switch on the ignition for at least 60 seconds.
X Start the engine.
i You can also have the AdBlue ®
tank refilled
at aq ualified specialist workshop.
Before driving your vehicle outside Europe, have
the AdBlue ®
supplyc hecked at aqualified spe-
cialist workshop.
Further information aboutB lueTEC exhaust gas
aftertreatmenta nd aboutAdBlue®
can
be obtained from any Mercedes-Benz Service
Centre.
Important safety notes AdBlue
®
is aw ater-solublef luid for the exhaust
gas aftertreatmentofd iesel engines. It is:
R non-toxic
R colourless and odourless
R non-flammable
If you open the AdBlue ®
tank, small amounts of
ammonia vapour may be released.
Ammonia vapours have apungent odour and are
particularlyi rritating to the skin, to mucous
membranes and to the eyes. You may experi-
ence aburning sensation in your eyes, nose and
throat. You may also experience coughing and
watery eyes.
Do not inhale any ammonia vapours that may be
released.O nly fill the AdBlue ®
tank in well-ven-
tilated areas. Do not swallow AdBlue
®
or let it come into con-
tact with skin, eyes or clothing. Keep AdBlue ®
awayf rom children.
If you or others come into contact with AdBlue ®
,
observe the following:
R immediately rinse AdBlue ®
off your skin with
soap and water.
R if AdBlue ®
comes into contact with your eyes,
immediately rinse them thoroughly with clean water. Seek medical attention immediately.
R if AdBlue ®
is swallowed, immediately rinse
your mouth out thoroughly. Drink plenty of
water. Seek medical attention immediately.
R change immediately out of clothing that has
come into contact with AdBlue ®
.
! Only use AdBlue ®
in accordance with
ISO 22241. Do not mix any additives with
AdBlue ®
,a nd do not dilute AdBlue ®
with
water. This may destroy the BlueTEC exhaust
gas aftertreatments ystem.
! In order to fill the AdBlue ®
tank, the vehicle
must be parked on alevel surface. The
AdBlue ®
tank can only be filled as intended
with the vehicle parked on alevel surface.
Fluctuations in capacity will thus be avoided.
Filling avehicle standing on an uneven sur-
face is not permitted. There is adanger of
overfilling, which can cause damage to Blue-
TEC exhaust gas aftertreatmentc omponents.
! Surfaces which have come into contact with
AdBlue ®
while refilling should be rinsed
immediately with water, or remove AdBlue ®
with amoist cloth and cold water. If AdBlue ®
has already crystallised,u seasponge and
cold water to clean the area. AdBlue ®
residue
crystallises after acertain amount of time and
soils the affected surfaces.
! AdBlue ®
is not afuel additive and must not
be added to the fuel tank. If AdBlue ®
is added
to the fuel tank, this can lead to engine dam-
age.
Have the AdBlue ®
tank refilled at aqualified
specialist workshop. However, you can also top
up the AdBlue ®
tank:
R at afilling station with an AdBlue ®
filling pump
R with AdBlue ®
refill bottles
R with an AdBlue ®
refill canister 170
RefuellingDriving and parking
Page 174 of 385
When the pump nozzle switches off automati-
cally during filling at afilling pump, the AdBlue ®
tank has been completely filled. Do not fill the
AdBlue ®
tank any further .AdBlue ®
may leak
out.
To avoid transportin galready opened refill con-
tainers in the vehicle, completely empty refill
bottles or canisters when filling the AdBlue ®
tank ,ifpossible.
Further information on AdBlue ®
(Y page 374).
Opening/closing the AdBlue ®
filler cap X
To open: switch the ignition off.
X Press the fuel filler flap in the direction of
arrow :.
The fuel filler flap swings up.
X Turn blue AdBlue ®
fuel filler cap ;anti-clock-
wise and remove it.
AdBlue ®
filler cap ;is secured with aplastic
strip.
X To close: fit AdBlue®
filler cap ;ontot he
filler neck and turn it clockwise.
X To close the fuel filler flap, press it in the
direction of arrow :.
X Drive faster than 15 km/h.
The Refill AdBlue See Owner’s Manual Refill AdBlue See Owner’s Manual
message goes out after approximately one
minute.
If the Refill AdBlue See Owner’s Manual
Refill AdBlue See Owner’s Manual
message continues to be shown in the multi-
function display, you must top up with more
AdBlue ®
.
i The fuel filler flap is unlocked or locked
automatically when you unlock or lock the
vehicle. AdBlue
®
refill canisters !
Do not fasten the disposable hose too
tightly. Otherwise, the disposable hose could
be damaged and AdBlue ®
could leak out. X
Unscrew the cap from the opening on top of
AdBlue ®
refill canister ;.
X Place disposable hose :on the opening of
AdBlue ®
refill canister ;and screw it on
clockwise until hand-tight.
Disposable hose :remains closed until you
fasten disposable hose :to the AdBlue ®
filler neck of the vehicle. X
Place disposable hose :on the filler neck on
the vehicle and screw it on clockwise until
hand-tight. When you feel resistance, dispos- able hose :is sufficiently secured.
X Lift up and tip AdBlue ®
refill canister ;.
Filling stops when the AdBlue ®
tank is com-
pletely filled. Do not fill the AdBlue ®
tank any
further .AdBlue ®
refill canister ;can be
removed when it has been only partially emp-
tied.
X Turn disposable hose :on the filler neck of
the vehicle anti-clockwise and remove it. Refuelling
171Driving and parking Z
Page 176 of 385
To ensure that the vehicle is safeguarded
against rolling away unintentionally:
R the electric parking brake must be applied
R on vehicles with manual transmission, engage
1st gear or reverse gear
R on vehicles with automatic transmission, the
transmission must be in position Pand the
key must be removed from the ignition lock
R the front wheels must be turned towards the
kerb on steep uphill or downhill gradients
R the empty vehicle must be secured at the
front axle with awheel chock or similar
object ,for example, on uphill or downhill gra-
dients
R al aden vehicle must also be secured at the
rear axle with awheel chock or similar object,
for example, on uphill or downhill gradients Switching off the engine
Important safety notes G
WARNING
The automatic transmission switches to neu-
tral position Nwhen you switch off the engine.
The vehicle may roll away.T here isarisk of an
accident.
After switching off the engine, alway sswitch
to parking position P.Prevent the parked vehi-
cle from rolling away by applying the parking
brake.
Vehicles with manual transmission X
Shift to either 1st gear or reverse gear R.
X Turn the key to position 0in the ignition lock
and remove it.
The immobiliser is activated.
X Apply the electric parking brake.
Vehicles with automatic transmission X
Apply the electric parking brake.
X Shift the transmission to position P.X
With the key: turn the key to position 0in the
ignition lock and remove it.
The immobiliser is activated.
X With the Start/Stop button: press the
Start/Stop button (Y page 145).
The engine stops and all the indicator lamps in the instrument cluster go out.
When the driver's door is closed, this corre-
sponds to key position 1.When the driver's
door is open, this corresponds to key position
0:" key removed".
If you switch the engine off with the transmis-
sion in position Ror D,t he automatic transmis-
sion shifts to Nautomatically.
With the key: if you then open the driver's door
or the front-passenger door or remove the key
from the ignition, the automatic transmission
shifts to Pautomatically.
With the Start/Stop button: if you then open
the driver's door or the front-passenger door,
the automatic transmission shifts to Pautomat-
ically.
If you want the automatic transmission to
remain in neutral N,e.g. when having the vehicle
cleaned in an automatic car wash with atowing
system:
X Vehicles with the Start-Stop button:
remove the Start-Stop button from the igni-
tion lock.
X Insert the key into the ignition lock.
X All vehicles: switch the ignition on.
X Depress the brake pedal and keep it
depressed.
X Shift to neutral N.
X Release the brake pedal.
X Release the electric parking brake.
X Switch off the ignition and leave the key in the
ignition lock.
The engine can be switched off while the vehicle is in motion by pressing and holding the Start/
Stop button for about three seconds. This func- tion operates independently of the ECO start/
stop automatic engine switch-off function. Parking
173Driving and parking Z
Page 177 of 385
Electric parking brake
General notes G
WARNING
If you leave childre nunattende dinthevehi-
cle ,the ym ay be able to set th evehicle in
motion if, for example, they:
R release th eparking brake
R shif tthe automatic transmission out of park
position Por shif tmanual transmission into
neutral
R start th eengine
In addition ,the ym ay operate vehicle equip-
men tand become trapped. Ther eisarisk of
an acciden tand injury.
When leavin gthe vehicle ,always tak ethe key
with you and loc kthe vehicle .Never leave
childre nunattende dinthevehicle.
The function of th eelectric parking brak eis
dependen tontheon-board voltage. If th eon-
boar dvoltage is low or if there is amalfunction
in th esystem, it may no tbepossible to apply the
released parking brake.
X If this is th ecase, only park th evehicle on
leve lground and secure it to prevent it from
rolling away.
X Vehicles with automatic transmission:
shif tthe automatic transmission to position
P .
X Vehicles with manua
ltra nsmission:
engage first gear.
It may no tbepossible to release an applied
parking brak eiftheon-board voltage is low or if
there is amalfunctio ninthesystem. Contac ta
qualified specialist workshop.
The electric parking brak ecarries out afunction
check at regular intervals when th eengine is
switched off .Noises that occur are normal. Applying or releasin
gmanually X
To apply: push handle :.
When th eelectric parking brak eisapplied,
th er ed ! indicator lamp light supinthe
instrumen tcluster.
The electric parking brak ecan also be applied
when th ekeyis removed.
X To release: pull handle:.
The red !indicator lamp in th einstrument
cluste rgoes out.
The electric parking brak ecan only be released:
R when th ekeyis in position 1or 2in th eigni-
tio nlock( Ypage 145) or
R if th eignition was switched on usin gthe
Start/Sto pbutton
Applying automatically (vehicles with
automatic transmission) The electric parking brak
eisautomatically
applied when th etransmission is in position P
and:
R thee ngine is switched off or
R thed river is no twearin gaseat belt and the
driver' sdoor is opened
To prevent th eelectric parking brak efromb eing
automaticall yapplied ,pull handle :.
The electric parking brak eisalso applied auto-
maticall yif:
R DISTRONIC PLU Sbrings th evehicle to a
standstil lor
R theH OLDf unction is keepin gthe vehicle sta-
tionary
R Activ eParking Assist is keepin gthe vehicle
stationary 174
ParkingDriving and parking