start stop button MERCEDES-BENZ C WAGON 2005 S203 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2005, Model line: C WAGON, Model: MERCEDES-BENZ C WAGON 2005 S203Pages: 426, PDF Size: 4.38 MB
Page 187 of 426
185 Controls in detail
Audio system
Manual tuning
Select desired waveband.
Press S or Tbutton for approx.
three seconds.
Press button repeatedly until desired
frequency has been reached.
Step-by-step station tuning takes place
in ascending or descending order. Each
time the button is pressed, the radio
tunes further by 0.2 MHz. During
manual tuning, the radio is muted.Automatic seek tuning
Select desired waveband.
Press S or T button briefly.
The radio will tune to the next highest
or next lowest receivable frequency.Scan search
Starting scan search
Select desired waveband.
Press
SC soft key.
SC will appear in the display. The
radio briefly tunes in all receivable
stations on the waveband selected.
iYou can only enter frequencies within
the respective waveband.
If a button is not pressed within
four seconds, the radio will return to
the last station tuned.
iIf no station is received after two
consecutive scans of the complete
frequency range, then the scan stops
at the frequency from which it began.
Page 189 of 426
187 Controls in detail
Audio system
Calling up stations
Press desired station button1
to R.
Leaving the Autostore memory level
Press
FM or
AM
soft key briefly.
Interrupting radio mode
The radio mode is interrupted by an
incoming call on the telephone*
(
page 205).
Mute on
Press U button.
The radio mode is interrupted and MUTED
appears in the display.
Mute off
Press U button.
The radio mode is again active.
Weather band
Press
WB soft key.
The weather band station last received
is tuned in.Selecting a weather band station
directly
Select desired weather band station
with buttons 1 to 7.
If a station cannot be tuned in, a search
is automatically started.
Search
Press S or T button to tune in
the next receivable weather band
station.iIf no weather band station is received
after three consecutive scans of the
complete frequency range, then the
scan stops at the channel with which it
began and
NO WB FOUND
appears in the
display.
If this happens, switch back to
standard radio mode.
Page 194 of 426
192 Controls in detailAudio systemTuning via scan search
Scan search is characterized as follows:
Scan search plays a channel for
approx. eight seconds and then skips
to the next channel within the current
category.
Scan search can be terminated
manually.
Press
SC soft key.
The search starts. SC appears in the
display.
Press
SC soft key again.
The search stops.Obtaining additional text information
Additional text information (artist, title)
related to the current channel can be
displayed.
Press
INF
soft key.
The title being played is displayed.
Press
INF
soft key again.
The name of the artist performing the
title being played is displayed.Storing stations
Tune in desired station.
Press and hold desired station
button1 to R until a brief signal
tone is heard.
The frequency is stored on the selected
station button.
The radio saves the current station at
the memory preset selected. The
memory preset selected appears in the
status line, e.g. S3.
iIf a button is not pressed within
four seconds, the radio will return to
the standard display.
iThere are ten presets available.
An existing entry is overwritten in the
memory list when a new entry is given.
Page 217 of 426
215 Controls in detail
Power windows
Power windows
Opening and closing the windows
The side windows can be opened and
closed electrically. The switches for all the
side windows are on the driver’s door. The
switches for the respective windows are
on the front passenger door and the rear
doors.
1Left front window
2Right front window
3Right rear window
4Left rear window
5Rear window override switch
(
page 77)
Warning!
G
When closing the windows, make sure there
is no danger of anyone being harmed by the
closing procedure.
The closing of the door windows can be im-
mediately halted by releasing the switch or,
if switch was pulled past the resistance
point and released, by either pressing or
pulling the respective switch.
If the window encounters an obstruction
that blocks its path in a circumstance where
you pulled the switch past the resistance
point and released it to close the window,
the automatic reversal function will stop the
window and open it slightly.
If the window encounters an obstruction
that blocks its path in a circumstance where
you are closing the window by pulling and
holding the switch, or by pressing and hold-
ing button‹ on the SmartKey, the auto-
matic reversal function will not operate.
When leaving the vehicle, always remove the
SmartKey from starter switch, take it with
you, and lock your vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. Unsuper-
vised use of vehicle equipment can cause an
accident and/or serious personal injury.
Page 328 of 426
326 Practical hintsUnlocking/locking in an emergencyUnlocking the vehicle
If you are unable to unlock the vehicle with
the SmartKey, open the driver’s door using
the mechanical key and the tailgate using
the emergency release.
Removing the mechanical key
1Mechanical key locking tab
2Mechanical key
Move locking tab1 in direction of
arrow.
Slide mechanical key2 out of the
housing.Unlocking the driver’s door
1Unlocking
Insert the mechanical key into the
driver’s door lock until it stops.
Turn the mechanical key counterclock-
wise to position1.
The driver’s door is unlocked.Unlocking and opening the tailgate
A minimum height clearance of 6.40 ft
(1.95 m) is required to open the tailgate.
The emergency release is located on the
inside of the tailgate.
1Release lever
2CoveriUnlocking the driver’s door with the
mechanical key will trigger the
anti-theft alarm system*.
To cancel the alarm, do one of the
following:
Press buttonŒ or‹ on the
SmartKey
Insert the SmartKey in the starter
switch
Page 329 of 426
327 Practical hints
Unlocking/locking in an emergency
Remove cover2 from the trim on the
tailgate.
Push release lever1 all the way to the
right.
Lift the tailgate.
Locking the vehicle
If you are unable to lock the vehicle with
the SmartKey, do the following:
Close the passenger doors and the
tailgate.
Press the central locking switch in the
center console (
page 96).
Check to see whether the locking
knobs on the passenger doors have
moved down.
If necessary push them down manually.
Except for the driver’s door, the vehicle
should now be locked.1Locking
Insert the mechanical key into the
driver’s door lock until it stops.
Turn the mechanical key clockwise to
position1.
The driver’s door is locked.
!Always make sure there is sufficient
overhead clearance.iIf the vehicle has previously been
locked from the outside using the
SmartKey, opening the tailgate from
the inside will trigger the anti-theft
alarm system*.
To cancel the alarm, do one of the
following:
Press buttonŒ or‹ on the
SmartKey
Insert the SmartKey in the starter
switch
Page 417 of 426
415 Index
Spare wheel bolts
For Minispare wheel 325
Speed
Setting current 224
Speed settings
Cruise control 225
Speedometer 25
Settings units 133
Speedometer display mode
Selecting 133
Split rear bench seat 230
SRS 68, 388
Indicator lamp 25, 299
Message in display 305
Standing lamps, front
Replacing bulbs 333
Standing lamps, rear
Replacing bulbs 333
Standing water
Driving instructions 263Starter switch 23, 33
Positions 33
Starting difficulties 47
Starting position 33
Starting the engine 46
Station (satellite radio)
selecting 190
Steering column
Height adjustment, electrical* 41
Height adjustment, manual 40
Length adjustment, electrical* 41
Length adjustment, manual 40
Steering gear oil
Message in display 319
Steering wheel
Adjusting 39
Buttons 26
Cleaning 291
Electrical adjustment* 40
Manual adjustment 40Stolen vehicle
Recovery services 249
Stopping
Tilt/sliding sunroof* 221
Windows 217
Storage compartments
Cargo compartment 227
Glove box 234
Storage spaces
Cup holder in rear seat armrest 237
Cup holders in front of
seat armrest 236
Storing
station (satellite radio) 192
Storing (Memory function*)
Positions into memory 106
Submenus
Convenience 144
For settings 121
In control system 123
Instrument cluster 133, 135