driver seat adjustment MERCEDES-BENZ CLA 2014 Owners Manual

XAdjust the seat and move the backrest to
an almostvertical position (Ypage 90).
XPull the seat belt smoothly through belt
sash guide.
XWithout twisting it, guide the shoulder
section of the seat belt across the middle
of your shoulder and the lap section across
your pelvis.
XEngage belt tonguein buckle".
XIf necessary, adjust the seat belt to the
appropriate height (Ypage 52).
XIf necessary, pull upwards on the shoulder
section of the seat belt to tighten the belt
across your body.
All seat belts in the vehicle with the exception
of the driver's seat belt are equipped with a
special seat belt retractor, with which a child
restraint system can be secured. For further
information on special seat belt retractors,
see (Ypage 57).
Information on releasing the seat belt with
release button!(Ypage 52).
Belt height adjustment
You can adjust the seat belt height on the
frontseats. Adjust the belt to a height that
allows the upper part of the seat belt to be
routed across the center of your shoulder.
XTo raise:slide the belt sash guide upwards.
The belt sash guide engages in various
positions.
XTo lower:press and hold belt sash guide
release.
XSlide the belt sash guide downwards.
XRelease belt sash guide releaseand
make sure that the belt sash guide has
engaged.
Releasing seat belts
!Make sure that the seat belt is fully rolled
up. Otherwise, the seat belt or belt tongue
will be trapped in the door or in the seat
mechanism. This could damage the door,
the door trim panel and the seat belt.
Damaged seat belts can no longer fulfill
their protective function and must be
replaced. Visit a qualified specialist
workshop.
XPress release button!on belt buckle".
XGuide belt tongueback to belt sash
guide.
Belt warning for the driver and front
passenger
Every time the engine is started, the
seat belt warning lamp lights up for six
seconds. It lights up regardless of whether
the driver's and front-passenger seat belts
have already been fastened. If the driver's
and front-passenger seat belts have already
been fastened, theseat belt warning
lamp then goes out.
52Occupant safety
Safety

in the installation instructions that are
included with the child restraint system.
Always read and follow the manufacturer's
instructions when using an infant or child
restraint system or booster seat.
Observe the warning labels in the vehicle
interior or on the infant or child restraint.
Special seat belt retractor
GWARNING
If you release the seat belt when driving, the
special seat belt retractor is deactivated.
The released seat belt cannot be engaged
again while driving, because the inertia reel
pulls in the seat belt a small distance. The
child restraint system is no longer properly
secured. There is an increased risk of serious
injury or even fatal injury.
Always keep the seat belt of the activated
special seat belt retractor engaged when
driving.
All seat belts except the driver's seat belt are
equipped with a special seat belt retractor.
When activated, the special seat belt
retractor ensures that the seat belt will not
slacken once the child restraint system has
been secured.
Installing a child restraint system:
XAlways comply with the manufacturer's
installation instructions.
XPull the seat belt smoothly fromthe seat
belt retractor.
XEngage the seat belt tongue in the belt
buckle.
Activating the special seat belt retractor:
XPull the seat belt out fully and let the seat
belt retractor retract it again.
While the seat belt is retracting, you should
hear a ratcheting sound. The special seat
belt retractor is activated.
XPush down on the child restraint system to
take up any slack.
Removing a child restraint system/
deactivating the special seat belt retractor:
XAlways comply with the manufacturer's
installation instructions.
XPress the seat belt release button and
guide the belt tongue to the belt outlet.
The special seat belt retractor is
deactivated.
Child restraint system on the front-
passenger seat
GWARNING
If the front-passenger front air bag is not
deactivated:
Ra child secured in a child restraint system
on the front-passenger seat could be
seriously or even fatally injured by the front-
passenger air bag deploying. This is
especially a risk if the child is in the
immediate vicinity of the front-passenger
air bag when it deploys.
Rnever secure a child on the front-passenger
seat in a rearward-facing child restraint
system. Only secure a rearward-facing
child restraint system on a suitable rear
seat.
Rand you secure a forward-facing child
restraint system to the front-passenger
seat, you must move the front-passenger
seat as far back as possible. When doing
so, ensure that the shoulder belt strap from
the belt outlet on the vehicle is routed
towards the front to the shoulder belt guide
on the child restraint system. Set the belt
height adjustment so that the belt strap is
routed towards the front along the bottom.
The front-passenger air bag is not
deactivated:
Ron vehicles without an air bag deactivation
system on the front-passenger seat.
Ron vehicles with an air bag deactivation
system on the front-passenger seat, unless
a child restraint system with transponders
Children in the vehicle57
Safety
Z

Useful information
iThis Operator's Manual describes all
models and all standard and optional
equipment of your vehicle available at the
time of publication of the Operator's
Manual. Country-specific differences are
possible. Please note that your vehicle may
not be equipped with all features
described. This also applies to safety-
related systems and functions.
iRead the information on qualified
specialist workshops: (Ypage 25).
Correct driver's seat position
GWARNING
You could lose control of your vehicle if you
do the following while driving:
Radjust the driver's seat, head restraint,
steering wheel or mirrors
Rfastenthe seat belt
There is a risk of an accident.
Adjust the driver's seat, head restraint,
steering wheel and mirror and fasten your
seat belt before starting the engine.
Observe the safety guidelines on seat
adjustment (Ypage 91).
XMake sure that seat"is adjusted
properly.
Manual seat adjustment (Ypage 92)
Electrical seat adjustment (Ypage 93)
When adjusting the seat, make sure that:
Ryou are as far away from the driver's air
bag as possible.
Ryou are sitting in a normal upright
position.
Ryou can fasten the seat belt properly.
Ryou have moved the backrest to an
almost vertical position.
Ryou have set the seat cushion angle so
that your thighs are gently supported.
Ryou can depress the pedals properly.
XCheck whether the head restraint is
adjusted properly (Ypage 93).
When doing so, make sure that you have
adjusted the head restraint so that the back
of your head is supported at eye level by
the center of the head restraint.
Observe the safety guidelines on steering
wheel adjustment (Ypage 96).
XMake sure that steering wheelis
adjusted properly.
Adjusting the steering wheel
(Ypage 97)
When adjusting the steering wheel, make
sure that:
Ryou can hold the steering wheel with your
arms slightly bent.
Ryou can move your legs freely.
Ryou can see all the displays in the
instrumentclusterclearly.
Observe the safety guidelines for seat belts
(Ypage 50).
XCheck whether you have fastened seat
beltproperly (Ypage 51).
90Correct driver's seat position
Seats, steering wheel and mirrors

The seat belt should:
Rfit snugly across your body
Rbe routed across the middle of your
shoulder
Rbe routed in your pelvic area across the
hip joints
XBefore starting off, adjust the rear-view
mirror and the exterior mirrors
(Ypage 97) in such a way that you have
a good view of road and traffic conditions.
XVehicles with a memory function:save
the seat and exterior mirror settings
(Ypage 100).
Seats
Important safety notes
GWARNING
Children could become trapped if they adjust
the seats, particularly when unattended.
There is a risk of injury.
When leaving the vehicle, always take the
SmartKey with you and lock the vehicle. Never
leave children unsupervised in the vehicle.
GWARNING
You could lose control of your vehicle if you
do the following while driving:
Radjust the driver's seat, head restraint,
steering wheel or mirrors
Rfasten the seat belt
There is a risk of an accident.
Adjust the driver's seat, head restraint,
steering wheel and mirror and fasten your
seat belt before starting the engine.
GWARNING
If you adjust the seat height carelessly, you or
other vehicle occupants could be trapped and
thereby injured. Children in particular could
accidentally press the electrical seat
adjustmentbuttons and become trapped.
There is a riskofinjury.
While moving the seats, make sure thatyour
hands or other body parts do not get under
the lever assembly of the seat adjustment
system.
GWARNING
When you adjust a seat, you or other vehicle
occupants could become trapped, e.g. on the
seat guide rail. There isarisk of injury.
Make sure when adjustingaseat that no one
has any body parts in the sweep of the seat.
GWARNING
The seat belt does not offer the intended level
of protection if the backrest is not in the
upright position.When braking or in the event
of an accident, you could slide underneath the
seat belt and sustain abdomen or neck
injuries, for example. This poses an increased
risk of injury or even fatal injury.
Adjust the seat properly before beginning
your journey. Always make sure that the seat
is in the upright position.
GWARNING
If head restraints are not installed and
adjusted correctly, they cannot provide
protection as intended. There is an increased
risk of injury in the head and neck area, e.g.
in the event of an accident or when braking.
Always drive with the head restraints
installed. Before driving off, make sure for
every vehicle occupant that the center of the
head restraint supports the back of the head
at about eye level.
GWARNING
According to accident statistics, children are
safer when properly restrained on the rear
seats than on the front-passenger seat. Thus,
we strongly recommend that children be
placed in the rear seat whenever possible.
Regardless of seating position, children 12
years old and under must be seated and
properly secured in an appropriately sized
child restraint system or booster seat
Seats91
Seats, steering wheel and mirrors
Z

Adjusting the seats electrically
Head restraintheight2
Seat cushion angle
"Seat height
!Seat fore-and-aft adjustment
Backrest angle
iYou can store the seat settings using the
memory function (Ypage 100).
Adjusting the head restraints
GWARNING
You could lose control of your vehicle if you
do the following while driving:
Radjust the driver's seat, head restraint,
steering wheel or mirrors
Rfasten the seat belt
There is a risk of an accident.
Adjust the driver's seat, head restraint,
steering wheel and mirror and fasten your
seat belt before starting the engine.
GWARNING
If head restraints are not installed and
adjusted correctly, they cannot provide
protection as intended. There is an increased
risk of injury in the head and neck area, e.g.
in the event of an accident or when braking.
Always drive with the head restraints
installed. Before driving off, make sure for
every vehicle occupant that the center of the
head restraint supports the back of the head
at about eye level.
General notes
For vehicles with sports seats, you cannot
adjust the head restraints or remove and
install the rear head restraints.
Adjusting the head restraints manually
Adjusting the head restraint height
XTo raise:pull the head restraint up to the
desired position.
XTo lower:press release catchin the
direction of the arrow and push the head
restraint down to the desired position.
Adjusting the fore/aft position of the
head restraint
2Not available on vehicles with sports seats.
Seats93
Seats, steering wheel and mirrors
Z

XTurn the SmartKey to position1or2in the
ignition lock (Ypage 137).
XPress buttonfor the left-hand exterior
mirror or buttonfor the right-hand
exterior mirror.
The indicator lamp in the corresponding
button lights up in red.
The indicator lamp goes out again after
some time. You can adjust the selected
mirror using adjustment button"as long
as the indicator lamp is lit.
XPress adjustmentbutton"up, down, or
to the left or right until you have adjusted
the exterior mirror to the correct position.
You should have a good overview of traffic
conditions.
The convex exteriormirrors provide a larger
field of vision.
The exterior mirrors are automatically heated
after starting the vehicle if the rear window
defroster is switched on and the outside
temperature is low. Heating takes a maximum
of 10 minutes.
iYou can also heat up the exterior mirrors
manually by switching on the rear window
defroster.
Folding the exterior mirrors in or out
electrically
XTurn the SmartKey to position1or2in the
ignition lock (Ypage 137).
XBriefly press button.
Both exterior mirrors fold in or out.
iMake sure that the exterior mirrors are
always folded out fully while driving. They
could otherwise vibrate.
iIf you are driving faster than 30 mph
(47 km/h), you can no longer fold in the
exterior mirrors.
Setting the exterior mirrors
If the battery has been disconnected or
completely discharged, the exterior mirrors
must be reset.The exterior mirrors will
otherwise not fold in when you select the
"Fold in mirrors when locking" function in the
on-board computer (Ypage 209).
XTurn the SmartKey to position1in the
ignition lock (Ypage 137).
XBriefly press button.
Folding the exterior mirrors in or out
automatically
If the "Fold in mirrors when locking" function
is activated in the on-board computer
(Ypage 209):
Rthe exterior mirrors fold in automatically as
soon as you lock the vehicle from the
outside.
Rthe exterior mirrors fold out again
automatically as soon as you unlock the
vehicle and then open the driver's or front-
passenger door.
iIf the exterior mirrors have been folded in
manually, they do not fold out.
Exterior mirror pushed out of position
If an exterior mirror has been pushed out of
position, proceed as follows:
XVehicles without electrically folding
exterior mirrors:move the exterior mirror
into the correct position manually.
XVehicles with electrically folding
exterior mirrors:press and hold mirror-
folding button (Ypage 98) until you hear a
98Mirrors
Seats, steering wheel and mirrors

click and then the mirrors engage in
position.
The mirror housing is engaged againand
you can adjustthe exterior mirrors as usual
(Ypage 97).
Automatic anti-glare mirrors
The "Automatic anti-glare mirrors" function is
only available if the vehicle is equipped with
the "Mirrors package".
The rear-view mirror and the exterior mirror
on the driver's side automatically go into anti-
glare mode if:
Rthe ignition is switched on and
Rincident light from headlamps strikes the
sensor in the rear-view mirror.
The mirrors do not go into anti-glare mode if
reverse gear is engaged or the interior lighting
is switched on.
Parking position for the exterior
mirror on the front-passenger side
General notes
The "Parking position of the exterior mirror on
the front-passenger side" function is only
available if the vehicle is equipped with the
"Mirrors package".
Setting and storing the parking position
Using reverse gear
You can position the front-passenger side
exterior mirror in such a way that you can see
the rear wheel on that side as soon as you
engage reverse gear. You can store this
position.
XMake sure that the vehicle is stationary.
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XPress buttonfor the exterior mirror on
the front-passenger side.
XEngage reverse gear.
The exterior mirror on the front-passenger
side moves to the preset parking position.
XUse adjustment button"to adjust the
exterior mirror. You should see the rear
wheel and the curb in the exterior mirror.
The parking position is stored.
iIf you shift the transmission to another
position, the exterior mirror on the front-
passenger side returns to the driving
position.
Using the memory button
You can position the front-passenger side
exterior mirror in such a way that you can see
the rear wheel on that side as soon as you
engage reverse gear. You can store this
position. This setting can be stored using
memory buttonM!.
XMake sure that the vehicle is stationary.
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XPress buttonfor the exterior mirror on
the front-passenger side.
XUse adjustment button"to adjust the
exterior mirror. You should see the rear
wheel and the curb in the exterior mirror.
Mirrors99
Seats, steering wheel and mirrors
Z

XPress memory buttonM!and one of the
arrows on adjustment button"within
three seconds.
The parking position is stored if the exterior
mirror does not move.
XIf the mirror moves out of position, repeat
the steps.
Calling up a stored parking position
setting
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XAdjust the exterior mirror on the front-
passenger side with the corresponding
button (Ypage 97).
XEngage reverse gear.
The exterior mirror on the front-passenger
side moves to the stored parking position.
The exterior mirror on the front-passenger
side moves back to its original position:
Ras soon as you exceed a speed of9mph
(15 km/h)
Rabout ten seconds after you have
disengaged reverse gear
Rif you press buttonfor the exterior
mirror on the driver's side
Memory functions
Storing settings
GWARNING
If you use the memoryfunctiononthe driver's
side while driving, you could lose control of
the vehicle as a result of the adjustments
being made. There is a risk of an accident.
Only use the memory function on the driver's
side when the vehicle is stationary.
GWARNING
When the memory function adjusts the seat,
you and other vehicle occupants–particularly
children–could become trapped. There is a
risk of injury.
While the memory function is making
adjustments, make sure that no one has any
body parts in the sweep of the seat. If
somebody becomes trapped, immediately
release the memory function position button.
The adjustmentprocess is stopped.
GWARNING
Children could become trapped if they
activate the memory function, particularly
when unattended.There isarisk of injury.
When leaving the vehicle, always take the
SmartKey with you and lock the vehicle. Never
leave children unsupervised in the vehicle.
With the memory function, you can store up
to three different settings, e.g. for three
differentpeople.
The following settings are stored as a single
memory preset:
Rposition of the seat, backrest and head
restraint
Rdriver's side: position of the exterior
mirrors on the driver's and front-passenger
sides
XAdjust the seat (Ypage 93).
XAdjust the exterior mirror on the driver's
side (Ypage 97).
XBriefly press theMmemory button and
then press storage position button1,2or
3within three seconds.
The settings are stored in the selected
preset position.Atone sounds when the
settings have been completed.
100Memory functions
Seats, steering wheel and mirrors