height MERCEDES-BENZ CLK63AMG 2008 C209 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2008, Model line: CLK63AMG, Model: MERCEDES-BENZ CLK63AMG 2008 C209Pages: 521
Page 43 of 521
42 Getting started
Adjusting
Seat adjustment
The seat adjustment switches are located
on the respective door.
1Head restraint height
2Seat height
3Seat cushion tilt
4Seat fore and aft adjustment
5Backrest tilt
Switch on the ignition (page 38).
or
Open the respective door.Seat fore and aft adjustment
Press switch forward or backward in
the direction of arrow4.
Seat height
Press switch up or down in the direc-
tion of arrow2.
Seat cushion tilt
Press switch up or down in the direc-
tion of arrow3 until your upper legs
are lightly supported.
Warning!G
According to accident statistics, children
are safer when properly restrained in the
rear seating positions than in the front seat-
ing position. Thus, we strongly recommend
that children be placed in the rear seats
whenever possible. Regardless of seating
position, children 12 years old and under
must be seated and properly secured in an
appropriate infant, or toddler restraint, or
booster seat recommended for the size and
weight of the child. For additional
information, see “Children in the vehicle”
(
page 83).
A child’s risk of serious or fatal injuries is
significantly increased if the child restraints
are not properly secured in the vehicle
and/or the child is not properly secured in
the child restraint.
iThe memory function (page 127) lets you
store the settings for the seat position together
with the settings for the steering wheel and the
exterior rear view mirrors.
!When moving the seats, make sure there are
no items in the footwell or behind the seats; oth-
erwise you could damage the seats.
Page 44 of 521
43 Getting started
Adjusting
Seat backrest tilt
Press switch forward or backward in
the direction of arrow5.
Head restraint height
Press switch up or down in the direc-
tion of arrow1.Head restraint adjusting
Manually adjust the head restraint.
Push or pull the head restraint cushion
to the desired position.
For more information, see “Seats”
(
page 120).Folding front seat backrests forward
1Release lever
Folding backrests forward
Pull release lever1 forward and fold
the backrest forward.
The head restraint will automatically
move down.
Warning!G
For your protection, drive only with properly
positioned head restraints.
Adjust the head restraint so that it is as
close to the head as possible and the center
of the head restraint supports the back of
the head at eye level. This will reduce the po-
tential for injury to the head and neck in the
event of an accident or similar situation.
Page 86 of 521
85 Safety and Security
Occupant safety
Your vehicle is equipped with air bag
technology designed to turn off the front
passenger front air bag in your vehicle
when the OCS senses the weight of a
typical 12-month-old child or less along
with the weight of a standard
appropriate child restraint on the front
passenger seat.
A child in a rear-facing child restraint on
the front passenger seat will be
seriously injured or even killed if the
front passenger front air bag inflates in
a collision which could occur under
some circumstances, even with the air
bag technology installed in your vehicle.
The only means to completely eliminate
this risk is to never place a child in a
rear-facing child restraint in the front
seat. We therefore strongly recommend
that you always place a child in a
rear-facing child restraint in the back
seat.
If you must install a rear-facing child
restraint on the front passenger seat
because circumstances require you to
do so, make sure the 56 indica-
tor lamp is illuminated, indicating that
the front passenger front air bag is deac-
tivated. Should the 56 indicator
lamp not illuminate or go out while the
restraint is installed, please check in-
stallation. Periodically check the
56 indicator lamp while driving
to make sure the 56indicator
lamp is illuminated. If the 56
indicator lamp goes out or remains out,
do not transport a child on the front pas-
senger seat until the system has been
repaired. A child in a rear-facing child re-
straint on the front passenger seat will
be seriously injured or even killed if the
front passenger front air bag inflates.
If you have to place a child in a
forward-facing child restraint on the
front passenger seat, move the seat as
far back as possible, use the proper
child restraint recommended for the
age, size and weight of the child, and
secure child restraint with the vehicle’s
seat belt according to the child seat
manufacturer’s instructions.
For children larger than the typical
12-month-old child, the front passenger
front air bag may or may not be activated
(
page 73).
Warning!G
Infants and small children should never
share a seat belt with another occupant.
During an accident, they could be crushed
between the occupant and seat belt.
A child’s risk of serious or fatal injuries is
significantly increased if the child restraints
are not properly secured in the vehicle
and/or the child is not properly secured in
the child restraint.
Children too big for a toddler restraint must
ride in seats using regular seat belts. Posi-
tion shoulder belt across chest and shoul-
der, not face or neck. A booster seat may be
necessary to achieve proper belt positioning
for children over 41 lbs until they reach a
height where a lap/shoulder belt fits
properly without a booster.
Page 88 of 521
87 Safety and Security
Occupant safety
Once the top tether anchorage hook is
attached, the child restraint itself can be
secured. Secure the child restraint and
tighten the top tether strap according to
the child restraint manufacturer’s instruc-
tions.
Child seat anchors – LATCH-type
The CLK coupe and cabriolet are equipped
with two LATCH- (L
ower Anchors and Teth-
ers for CH
ildren) type anchors (at each of
the rear seats) for the installation of a
LATCH-type child seat with matching
mounting fittings.LATCH-type anchors
The LATCH-type anchors are located be-
tween the seat cushion and the backrest.
1AnchorsInstall child seat according to the
manufacturer’s instructions.
Warning!G
Always lock backrest in its upright position
when rear seat bench is occupied by pas-
sengers, or the extended cargo area is not in
use. Check for secure locking by pushing
and pulling on the backrest.
Warning!G
Children too big for a toddler restraint must
ride in seats using regular seat belts.
Position shoulder belt across chest and
shoulder, not face or neck.
A booster seat may be necessary to achieve
proper belt positioning for children over
41 lbs until they reach a height where a
lap/shoulder belt fits properly without a
booster.
Install child seat according to manufactur-
er’s instructions.
T h e c h i l d s e a t m u s t b e f i r m l y a t t a c h e d t o t h e
right and left side anchor.
An incorrectly mounted child seat may come
loose during an accident which could result
in serious injury or death to the child.
Damaged or impact damaged child seats or
child seat anchor fittings must be replaced.
Do not leave children unattended in the
vehicle, even if the children are secured in a
child restraint system.
iNon-LATCH-type child seats may also be
used and can be installed using the vehicle’s
seat belt system (
page 83). Install child seat
according to the manufacturer’s instructions.
Page 104 of 521
103 Controls in detail
Locking and unlocking
The locking knobs in the doors
move up.
The anti-theft alarm system is dis-
armed.
Global locking
Press button‹.
With the trunk and both doors closed:
All turn signal lamps flash three
times.
An acoustic signal sounds three
times.
The locking knobs in the doors
move down.
The anti-theft alarm system is
armed.
Restoring to factory setting
Press and hold buttonsŒ and‹
simultaneously for about 5 seconds un-
til battery check lamp5 (
page 100)
flashes twice.Unlocking and opening the trunk
You can unlock and open the trunk
separately.
A minimum height clearance of 5.71 ft
(1.74 m) CLK coupe or 5.41 ft (1.65 m)
CLK cabriolet is required to open the
trunk lid.
Press and hold button Š until trunk
unlocks and begins to open.
The trunk can also be opened from its
inside in an emergency, see “Trunk emer-
gency release” (
page 117).
SmartKey with KEYLESS-GO*
Vehicles equipped with KEYLESS-GO come
with two SmartKeys with KEYLESS-GO,
each with remote control and a removable
mechanical key.
The KEYLESS-GO function is integrated
into the SmartKey. On these vehicles, the
validity of the SmartKey with KEYLESS-GO
is checked every time you pull an outside
door handle.
If the SmartKey with KEYLESS-GO is valid,
your vehicle unlocks
the doors
the trunk
the fuel filler flap
the glove box
!The trunk lid swings open upwards automat-
ically. Always make sure there is sufficient over-
head clearance.
Vehicles with trunk opening/closing system*: To
stop the opening procedure, press button Š.
The trunk lid stops moving.
iIf the trunk does not open, it is still locked
separately (
page 118).
Page 109 of 521
108 Controls in detail
Locking and unlocking
Global locking
Press the lock button on an outside
door handle.
With the trunk and both doors closed:
All turn signal lamps flash three
times.
An acoustic signal sounds three
times.
The locking knobs in the doors
move down.
The anti-theft alarm system is
armed.
Restoring to factory setting
Press and hold buttonsŒ and‹
simultaneously for about 5 seconds un-
til Battery check lamp5 (
page 104)
flashes twice.Unlocking and opening the trunk
You can unlock and open the trunk sepa-
rately.
A minimum height clearance of 5.71 ft
(1.74 m) CLK coupe or 5.41 ft (1.65 m)
CLK cabriolet is required to open the
trunk lid.
Press and hold button Š until trunk
unlocks and begins to open.
The trunk can also be opened from its in-
side in an emergency, see “Trunk emer-
gency release” (
page 117).Checking the batteries in the SmartKey
or SmartKey with KEYLESS-GO*
Press button‹orŒ.
Battery check lamp (
page 100) or
(
page 104) comes on briefly to indi-
cate that the SmartKey or SmartKey
with KEYLESS-GO batteries are in
order.
iVehicles with trunk opening/closing sys-
tem*, you can also lock the vehicle using the
KEYLESS-GO locking/closing switch
(
page 116) on the trunk lid.
!The trunk lid swings open upwards automat-
ically. Always make sure there is sufficient over-
head clearance.
Vehicles with trunk opening/closing system*: To
stop the opening procedure, press button Š.
The trunk lid stops moving.
iIf the trunk does not open, it is still locked
separately (
page 118).
!If battery check lamp does not come on
briefly during check, the SmartKey or SmartKey
with KEYLESS-GO batteries are discharged.
Replace the batteries (
page 441).
You can obtain the required batteries at any au-
thorized Mercedes-Benz Center.
iIf the batteries are checked within signal
range of the vehicle, pressing the‹orŒ
button will lock or unlock the vehicle
accordingly.
Page 111 of 521
110 Controls in detail
Locking and unlocking
Pull on door handle2.
If door was locked, locking knob1 will
move up.
Opening the trunk
You can open the trunk if the vehicle is sta-
tionary.
A minimum height clearance of 5.71 ft
(1.74 m) CLK coupe or 5.41 ft (1.65 m)
CLK cabriolet is required to open the
trunk lid.Opening the trunk from the outside
1Handle
Press and hold button Š on the
SmartKey or SmartKey with
KEYLESS-GO* until trunk unlocks and
begins to open.
or
Pull on handle1.
In vehicles without KEYLESS-GO*:
The vehicle must be unlocked.
The SmartKey with KEYLESS-GO* must be
inside the vehicle.
Pull an outside door handle.
The SmartKey with KEYLESS-GO* must be
within 3 ft (1 m) of the vehicle.
iIf you hear a warning signal you have
forgotten to switch off the low beam headlamps
or the parking lamps before opening the driver’s
door.
In addition the message
Switch Off Lights
appears in the multifunction display.
Switch off the low beam headlamps or the park-
ing lamps.
If the message
Switch Off Lights or Re-
move Key
appears in the multifunction display
remove the SmartKey from the starter switch or
switch off the automatic headlamp mode.
!Failure to switch off the exterior lamps when
leaving the vehicle may result in a discharged
battery.
Warning!G
Make sure the trunk is closed when the en-
gine is running and while driving. Among
other dangers, such as blocked visibility, ex-
haust fumes may enter the vehicle interior.
These fumes are damaging to your health.
!The trunk lid swings open upwards automat-
ically. Always make sure there is sufficient over-
head clearance.
iIf the trunk does not open, it is still locked
separately (
page 118).
Page 121 of 521
120 Controls in detail
Seats
For information on seat adjustment, see
“Adjusting” (
page 41).
Front seat active head restraints
You cannot remove the active head re-
straints on the driver’s and front passen-
ger’s seat.
For removal of the active head restraints
we recommend that you contact an
authorized Mercedes-Benz Center.
For information on head restraint adjust-
ment, see “Seats” (
page 41).For information on active head restraints,
see “Active head restraints” (
page 81).
Rear seat head restraints (CLK coupe)Head restraint height
1Release button
Warning!G
For your protection, drive only with properly
positioned head restraints.
Adjust the head restraint so that it is as
close to the head as possible and the center
of the head restraint supports the back of
the head at eye level. This will reduce the po-
tential for injury to the head and neck in the
event of an accident or similar situation.
Warning!G
For safety reasons, always drive with the
rear head restraints in the upright position
when the rear seats are occupied.
Keep the area around head restraints clear
of articles (e.g. clothing) to not obstruct the
folding operation of the head restraints.
iAdjust the head restraint in such a way that
it is as close to the head as possible.
Warning!G
For your protection, drive only with properly
positioned head restraints.
Adjust the head restraint so that it is as
close to the head as possible and the center
of the head restraint supports the back of
the head at eye level. This will reduce the po-
tential for injury to the head and neck in the
event of an accident or similar situation.
Page 122 of 521
121 Controls in detail
Seats
Raising
Manually adjust the height of the head
restraint by pulling it upward.
If the head restraint is fully retracted,
push release button1 and pull the
head restraint up.
Lowering
To lower the head restraint, push
release button1 and push down on
the head restraint.Folding head restraints back with re-
lease button
1Release button
Push release button1.
The head restraints will fold backward.Folding head restraints back with
switch in the center console
1Rear head restraints folding switchStart the engine (page 51).
Press switch1 to release the head re-
straints.
The head restraints will fold backward.
Do not drive the vehicle without the seat
head restraints. Head restraints are
intended to help reduce injuries during an
accident.
iAdjust the head restraint in such a way that
it is as close to the head as possible.
iYou can also fold the head restraints back
using the switch in the center console.
Page 125 of 521
124 Controls in detail
Seats
Multicontour seat*
The multicontour seat has a movable seat
cushion and inflatable air cushions built
into the backrest to provide additional
lumbar and side support.
The seat cushion movement, backrest
cushion height and curvature can be
continuously varied with switches on the
side of the seat after the ignition is
switched on (
page 40).1Seat cushion depth
2Backrest bottom
3Backrest center
4Side bolster adjustment
Switch on ignition (page 40).Seat cushion depth
Adjust the seat cushion depth to the
length of your upper leg using
switch1.
Backrest contour
Adjust the contour of the backrest to
the desired position using switches2
and3.
Backrest side bolsters
Adjust the backrest side bolsters so
that they provide good lateral support
using switch4.
iIf, after a period of time, the seat no longer
provides the desired contour, then repeat the ad-
justment procedure.