sbc MERCEDES-BENZ E320 2003 W211 User Guide

296 Practical hintsWhat to do if …Display
Possible cause
Suggested solution
ABS
defective!
Visit workshop!
The ABS has detected a malfunction and
has switched off. The ESP and the BAS are
also deactivated. The SBC brake system is
still functioning normally but without the
ABS available.

Continue driving with added caution.
Wheels will lock during hard braking,
reducing steering capability.

Have the system checked at an au-
thorized Mercedes-Benz Center as
soon as possible.
Failure to follow these instructions in-
creases the risk of accident.
Display defective
Visit workshop!
The ABS or the ABS display is malfunction-
ing.

Continue driving with added caution.

Visit an authorized
Mercedes-Benz Center as soon as
possible.
Failure to follow these instructions in-
creases the risk of accident.

297 Practical hints
What to do if …
ABS
Braking system
not working!
The charging voltage has fallen below
10 volts and the ABS has switched off.
The brake system is still functioning nor-
mally but without the ABS available.

When the voltage is above this value
again, the ABS is operational again.

Continue driving with added caution.
Wheels will lock during hard braking,
reducing steering capability.

Have the system checked at an au-
thorized Mercedes-Benz Center as
soon as possible.
Failure to follow these instructions in-
creases the risk of accident.
BAS
defective!
Visit workshop!
The BAS has detected a malfunction and
switched off. The SBC brake system is still
functioning normally but without the BAS
available.

Continue driving with added caution.

Visit an authorized Mercedes-Benz
Center as soon as possible.
Failure to follow these instructions in-
creases the risk of accident.
BAS
Display malfunction
Visit workshop!
The BAS or the BAS display is malfunction-
ing.

Continue driving with added caution.

Visit an authorized Mercedes-Benz
Center as soon as possible.
Failure to follow these instructions in-
creases the risk of accident.
Display
Possible cause
Suggested solution

298 Practical hintsWhat to do if …BAS
not available!
See operator’s manual
The charging voltage has fallen below
10 volts and the BAS has switched off.
The brake system is still functioning nor-
mally but without the BAS available.

When the voltage is above this value
again, the BAS is operational again.

Have the system checked at an au-
thorized Mercedes-Benz Center if
you see the warning message for a
longer period of time.
Failure to follow these instructions in-
creases the risk of accident.
ESP
Malfunction!
Visit workshop!
The ESP is deactivated because of a mal-
function or interrupted power supply. The
SBC brake system is still functioning nor-
mally. The ABS may still be operational.

With the vehicle stationary, turn the
steering wheel completely to the left
and then to the right to synchronize
the ESP.
If the ESP message does not go out:

Continue driving with added caution.

Visit an authorized
Mercedes-Benz Center as soon as
possible.
Failure to follow these instructions in-
creases the risk of accident.
Display
Possible cause
Suggested solution

299 Practical hints
What to do if …
ESP
Display defective
Visit workshop!
The BAS or the BAS display is malfunction-
ing.

Continue driving with added caution.

Visit an authorized Mercedes-Benz
Center as soon as possible.
Failure to follow these instructions in-
creases the risk of accident.
ESP
not available!
See operator‘s manual
The ESP is deactivated because of a mal-
function or interrupted power supply. The
SBC brake system is still functioning nor-
mally. The ABS may still be operational.

With the vehicle stationary, turn the
steering wheel completely to the left
and then to the right to synchronize
the ESP.
If the ESP message does not go out:

Continue driving with added caution.

Visit an authorized
Mercedes-Benz Center as soon as
possible.
Failure to follow these instructions in-
creases the risk of accident.
:
Engine oil leve
l
Stop, engine off!
There is no oil in the engine. There is a dan-
ger of engine damage.

Carefully bring the vehicle to a halt
as soon as possible.

Turn off the engine.

Add engine oil.
Display
Possible cause
Suggested solution

303 Practical hints
What to do if …
G
Display defective
The instrument cluster display is malfunc-
tioning.

Continue driving with added caution.

Visit an authorized Mercedes-Benz
Center as soon as possible.
G

Display defective
Visit workshop!
The displays for several systems have mal-
functioned. Some systems themselves may
also have malfunctioned.

Have the electronic systems
checked by an authorized
Mercedes-Benz Center.
L
Visit workshop!
One or more main functions of the Tele Aid
system are malfunctioning.

Have the Tele Aid system checked by
an authorized Mercedes-Benz Cen-
ter.
#
Malfunction
Electrical consumers
switched off
The consumer battery has insufficient volt-
age and can no longer supply the conve-
nience functions such as seat ventilation*.
The electrical consumers will come back
online as soon as on-board voltage is
sufficient.
#
Battery/Alternator
Stop vehicle!
The battery is malfunctioning.
The SBC brake system requires electrical
energy and therefore has only limited oper-
ation. Considerably greater brake pedal
force is required and the stopping distance
is increased.

Stop the vehicle as soon as it is safe
to do so. Adjust driving to be consis-
tent with reduced braking respon-
siveness.

Notify an authorized Mercedes-Benz
Center.
#
Undervoltage
Charge battery
The battery has insufficient voltage.

Start the engine (
page 43).
Display
Possible cause
Suggested solution

305 Practical hints
What to do if …
2
Brake wear
Visit workshop!
The brake pads have reached their wear
limit.

Brake pad thickness must be visually
inspected at the intervals specified in
the Service Booklet.

Have the brake pads replaced as
soon as possible.
T
Brake malfunction
Stop vehicle
The SBC brake system is in the limp-home
(emergency operation) mode. Consider-
ably greater brake pedal force is required
and the stopping distance is increased.
Do not exceed a speed of 55 mph
(90 km/h).

Do not drive any further.

Significantly greater force must be
applied to the brake pedal.

Call for roadside assistance.
Except Canada:;Canada only:3
Reduced braking effect
Start engine!
Increased braking dis-
tance
Start engine!
The battery has insufficient voltage and
cannot supply sufficient power to the SBC
brake system.

Start the engine.
The message disappears when suffi-
cient voltage is available
Display
Possible cause
Suggested solution

306 Practical hintsWhat to do if …Except Canada:;Canada only:3
Reduced braking effect
Visit workshop!
Increased braking dis-
tance
Visit workshop!
The SBC brake system is in the limp-home
(emergency operation) mode. Consider-
able brake pedal force is required and the
stopping distance is increased.

Continue driving with added caution.

Adjust driving to be consistent with
reduced braking responsiveness.
Brake fluid
Visit workshop!
There is insufficient brake fluid in the reser-
voir.

Risk of accident! Stop the vehicle
and notify an authorized
Mercedes-Benz Center. Do not add
brake fluid! This will not solve the
problem.
Except Canada:;Canada only:3
Service brake
Visit workshop!
There are malfunctions, but the SBC brake
system is operating normally.

Visit an authorized Mercedes-Benz
Center as soon as possible.
Display
Possible cause
Suggested solution

307 Practical hints
What to do if …
Except Canada:;Canada only:3
Brakes overheated!
Drive carefully!
The brake system is overheated due to an
excessive load on the brakes.

Relieve the load on the brake sys-
tem.

Drive more smoothly and think
ahead to avoid unnecessary braking.

When driving down slopes, shift into
a lower gear to use the engine’s brak-
ing power (
page 153).

Cautiously continue driving so that
the air stream will cool down the
brakes.
Display
Possible cause
Suggested solution
Warning!
G
Driving while these messages are displayed
can result in an accident. Have your brake
system checked immediately.
If there is a malfunction in the SBC brake
system, we recommend that the vehicle be
transported with all wheels off the ground
using flatbed or appropriate wheel lift/dolly
equipment. A tow bar must be used if cir-
cumstances do not permit the use of the
recommended towing methods and the ve-
hicle requires towing with all four wheels on
the ground. Towing the vehicle with all four
wheels on the ground is only permissible for
distances up to 30 miles (50 km) and at a
speed not to exceed 30 mph (50 km/h). For
more information, refer to "Towing the vehi-
cle" (
page 348).
If the SBC brake system enters its
limp-home (emergency operation) mode,
the driver must apply significantly greater
brake pedal pressure and depress the pedal
much further than normal to obtain braking
effect. If necessary, apply full pressure to
the brake pedal. Brakes are only applied to
the front wheels. Stopping distance is in-
creased!
Low brake fluid in the reservoir may cause
the braking system to fail!
Don’t add brake fluid before checking the
brake system. Overfilling the brake fluid

349 Practical hints
Towing the vehicle
Warning!
G
If circumstances require towing the vehicle
with all wheels on the ground, always tow
with a tow bar if:

the engine will not run


there is a malfunction in the SBC brake
system


there is a malfunction in the power sup-
ply or in the vehicle’s electrical system
as that will be necessary to adequately con-
trol the towed vehicle.
Prior to towing the vehicle with all wheels on
the ground, make certain that the key is in
starter switch position2.
If the key is left in the starter switch
position0 for an extended period of time, it
can no longer be turned in the switch. In this
case, the steering is locked. To unlock, re-
move key from starter switch and reinsert.
iTo signal turns while being towed with
the hazard warning flasher in use, turn
key in starter switch to position2 and
activate the combination switch for the
left or right turn signal in the usual
manner – only the selected turn signal
will operate.
Upon canceling the turn signal, the haz-
ard warning flasher will operate again.
Warning!
G
The brake system requires electrical power
to operate.
A malfunction in the vehicle’s power supply
or electrical system may impair brake sys-
tem operation and switch it into its
limp-home (emergency operation) mode. To
brake, the driver must then apply signifi-
cantly greater brake pedal pressure and de-
press the pedal much further to obtain the
expected braking effect. If necessary, apply
full pressure to the brake pedal. Brakes are
only applied to the front wheels. Stopping
distance is increased! Adapt your driving
style accordingly. SBC brake system
(page 77).
With the engine not running, there is no
power assistance for the steering system. In
this case, it is important to keep in mind that
a considerably higher degree of effort is nec-
essary to steer the vehicle. Adapt your driv-
ing accordingly.

379 Technical terms
Restraint systems
Seat belts, belt tensioners, airbags and
child restraint systems. As indepen-
dent systems, their protective func-
tions complement one another.
RON
(R
esearch O
ctane N
umber)
The Research Octane Number for gaso-
line as determined by a standardized
method. It is an indication of a gaso-
line's ability to resist undesired detona-
tion (knocking). The average of both
the ->MON (Motor Octane Number)
and RON (Research Octane Number) is
posted at the pump, also known as
ANTI-KNOCK INDEX.
SBC
(S
ensotronic B
rake C
ontrol)
Electronically controlled hydraulic
braking system for increased braking
safety and comfort.Shift lock
When the vehicle is parked, this lock
prevents the transmission selector le-
ver from being moved out of positionP
without key turned and brake pedal de-
pressed.
SRS
(S
upplemental R
estraint S
ystem)
Seat belts, emergency tensioning de-
vice and airbags. Though independent
systems, they are closely interfaced to
provide effective occupant protection.
Tele Aid System
(T
elematic A
larm I
dentification on D
e-
mand)
The Tele Aid system consists of three
types of response: automatic and man-
ual emergency, roadside assistance
and information. Tele Aid is initially ac-
tivated by completing a subscriber
agreement and placing an acquain-
tance call.The Tele Aid system is operational pro-
viding that the vehicle’s battery is
charged, properly connected, not dam-
aged and cellular and GPS coverage is
available.
Telematics*
A combination of the terms "telecom-
munications" and "informatics".
Tightening torque
Force times lever arm (e.g. a lug
wrench) with which threaded fasteners
such as wheel bolts are tightened.
Tire speed rating
Part of a tire designation; indicates the
speed range for which a tire is ap-
proved.
Traction
Force exerted by the vehicle on the
road via the tires.