engine MERCEDES-BENZ EQC SUV 2022 User Guide

#
Push handle 1ofthe bonnet catch upwards
and liT the bonnet until it opens automaticall y.
Closing t
Closing t he bonnet
he bonnet #
Lowe rth e bonnet toa height of around 20 cm
and then allow it tofall, applying a little force
as you let it go. #
Ifth e bonnet can still be liTed slightl y,open
th e bonnet again and close it with a little more
fo rc e until it engages cor rectl y. Chec
Chec
king t
king t he coolant lev
he coolant lev el
el &
W
WARNING
ARNING Risk of burns from hot compo-
nents in the engine compartment
Cer tain components in the engine compart-
ment can be very hot, e.g. the drive system
and the cooler. #
Allow the drive system tocool down and
to uch only the components described
belo w. &
W WARNI NG
ARNI NGRisk of scalding from hot cool-
ant
Yo u may scald yourself if you open the cap
when the drive system is at normal operating
te mp erature. #
Let theve hicle cool down before opening
th e cap. #
When opening the cap, wear pr otective
glo ves and saf ety glasses. #
Open the cap slo wlytorelease pressure. #
Park theve hicle on a le vel sur face. #
Check the coolant temp erature display on the
inst rument displa y.
The coolant temp erature must be below 40°C. Maintenance and care
307 307

#
Slowly turn cap 1anti-clockwise torelease
ove rpressure. #
Continue turning cap 1anti-clockwise and
re mo veit. #
Ifth e coolant le vel is below mar ker bar 2,
visit a quali/ed specialist workshop, such as a
Mercedes-Benz Se rvice Centre. Ha vethe
coolant checked or re/lled on lyat a quali/ed
specialist workshop. T
T
opping up t
opping up t he windscr
he windscreen w
een washer syst
asher syst em
em &
W
WARNING
ARNING Risk of burns from hot compo-
nents in the engine compartment
Cer tain components in the engine compart-
ment can be very hot, e.g. the drive system
and the cooler. #
Allow the drive system tocool down and
to uch only the components described
belo w. &
W
WARNI NG
ARNI NGRisk of /re and injury from
windscre enwasher concent rate
Wi ndsc reen washer concent rate is highly 0am-
mable. #
Avoid /re, naked 0ames, smoking and
th e creation of spar kswhen using wind-
screen washer concent rate. #
Remo vecap 1bytheta b. #
Top up thewa sher 0uid.
% Further information about the windscreen
wa sher 0uid (/ page 354) K
K
eeping t
eeping t he air/w
he air/w at
ater duct fr
er duct fr ee
ee #
Keep the area between the bonnet and the
windscreen free of deposits, e.g. ice, snow or
lea ves. Cleaning and care Cleaning and care
Inf
Inf
or
ormation on w
mation on w ashing t
ashing the v
he vehicle in a car w
ehicle in a car w ash
ash &
W
WARNING
ARNING Risk of an accident due to
re duced braking po wer aTer washing the
ve hicle
Braking e1ciency is reduced aTer washing the
ve hicle. #
ATer theve hicle has been washed, brake
carefully while paying attention tothe
tra1c conditions until braking po wer has
been fully restored. 308
308
Maintenance and ca
re

To
avo id damage toyour vehicle, obser vethefo l-
lowing when using a high-pressure cleaner:
R The key is at a minimum dis tance of 3 m away
from theve hicle. Otherwise theta ilgate could
open unintentionall y.
R Maintain a distance of at least 30 cm tothe
ve hicle.
R V
V ehicles wit
ehicles with decor h decorativ
ative f
e foil:
oil: Parts of your
ve hicle are co vered with a decorative foil.
Maintain a distance of at least 70 cm between
th efo il-co vered parts of theve hicle and the
nozzle of the high-pressure cleaner. Mo vethe
high-pressure cleaner nozzle around whilst
cleaning. The waterte mp erature of the high-
pressure cleaner must not exceed 60°C.
R Obser vethe information on the cor rect dis-
ta nce in the equipment manufacturer's opera-
to r manual.
R Do not direct the nozzle of the high-pressure
cleaner directly at sensitive parts such as
tyres, gaps, electrical component parts, bat-
te ries, illuminants and louvres. W W
ashing t
ashing t he v
he vehicle b
ehicle b y hand
y hand Obser
vethere leva nt legal requ irements (e.g. in
some countries, washing byhand is permitted
only in special lydesignated wash ba ys). #
Use a mild cleaning agent (e.g. car shampoo). #
Washtheve hicle with luk ewarm water using a
soT car sponge. When doing so, do not
ex pose theve hicle todirect sunlight. #
Carefully hose theve hicle o. with water and
dry using a chamois.
% Obser vethe no tes on the care of car parts
(/ page 312). N
No
ot
tes on paintw
es on paintw or
ork/matt
k/matt /nish
/nishpaintw
paintw or
ork care
k care To
avo id damaging the paintwork and inter fering
with the driving assistance systems, please
obser vethefo llowing no tes:
P
P aint
aint
R Insect remains: Soak with insect remo ver and
ri nse o. the treated areas aTer wards.
R Bird droppings: Soak with water and rinse o.
aTer wards. R
Tree resin, oils, fuels and greases: remo veby
ru bbing gently with a clo thsoaked in petro-
leum ether or lighter 0uid.
R Coolant and brake 0uid: remo vewith a damp
clo thand clean water.
R Tar stains: use tarre mo ver.
R Wax: use silicone remo ver.
R Do not attach sti ckers, /lms or similar materi-
als. Only ha ve/lm attached tothe bumper at
a quali/ed specialist workshop.
R Remo vedirt immediatel y,where possible.
Matt
Matt /nish
/nish
R Only use care products appr ovedfor
Mercedes-Benz.
R Do not attach stic kers, /lms or similar materi-
als. Only ha ve/lm attached tothe bumper at
a qu ali/ed specialist workshop.
R Do not polish theve hicle and light-alloy
wheels.
R Only use car washes that cor respond tothe
latest engineering standards. 310
310
Maintenance and care

#
Use only fuses appr ovedfo r Mercedes-
Benz with there specti vespeci/ed fuse
ra ting. Blown fuses must be
replaced with fuses of the
same rating, whi chyou can recognise bythe col-
our and the label. The fuse ratings and fur ther
information tobe obser ved can be found in the
fuse assignment dia gram.
F
F use assignment diagr
use assignment diagr am:
am:onthe fuse box in the
load compartment (/ page 331).
* NO
NO TE
TEDamage or malfunctions caused by
moisture Moisture may cause damage
tothe electrical
system or cause it tomalfunction. #
When the fuse box is open, make sure
th at no moisture can enter the fuse box. #
When closing the fuse box, make sure
th at the seal of the lid is positioned cor-
re ctly on the fuse box. If
th e ne wlyinser ted fuse also blo ws, ha vethe
cause traced and recti/ed at a quali/ed specialist
wo rkshop.
Ensure thefo llowing before replacing a fuse:
R The vehicle is secured against rolling away.
R All electrical consume rsare switched o..
R The vehicle is switched o..
The elect rical fuses are located in various fuse
bo xes:
R Fuse box in the engine compartment on the
driver's side (/ page 329)
R Fuse box on the driver's side of the cockpit
(/ page 330)
R Fuse box in the front passenger foot we ll
(/ page 330)
R Fuse box in the load compartment on the
ri ght-hand side of theve hicle, when vie wed in
th e direction of tr avel (/ page 331) Opening and closing t
Opening and closing t
he fuse bo
he fuse box in t
x in the engine
he engine
com
com par
partment
tment R R
eq eq uir
uir ements:
ements:
R A dry clo thand a scr ewdriver are available.
Obser vethe no tes on elect rical fuses
(/ page 328).
Opening
Opening &
W
WARNING
ARNING Risk of injury from using the
windscreen wipers when the bonnet is
open
If th e windscreen wipers start moving when
th e bonnet is open, you could be trapped by
th e wiper linkage. #
Always switch o. the windscreen wipers
and theve hicle /r stifyo u need toopen
th e bonnet. Breakdown assistance
329
329

N
N
o
ot
tes on t
es on t ec
echnical data
hnical data
The tech nical data was de term ined in accordance
with EU Directives. The data stated only applies to
ve hicles with standard equipment. You can obtain
fur ther information from a Mercedes-Benz Service
Centre.
Onl
Onl y f y for cert
or cert ain countr
ain countr ies:
ies:you can /n dvehicle-
speci/c vehicle data in theCO C documents (CER-
TIFIC ATE OF CONFORMITY). These documents
are supplied when theve hicle is deli vered. On-boar
On-boar
d electr
d electronics
onics N
No
ot
tes on t
es on t am
amper
per ing wit
ing wit h t
h the engine electr
he engine electr onics
onics*
N
NOOTE
TE Premature wearthro ugh improper
maintenance Improper maintenance may cause
vehicle
components towe ar more quickly and the
ve hicle's operating permit may be in validated. #
Always ha veworkon the engine elec-
tronics and related components car ried
out at a quali/ed specialist workshop. T
T
w
w o-wa
o-wa y r
y radios
adios N
No
ot
tes on
es on /tting
/tting tw
two-wa
o-wa y r
y radios
adios &
W
WARNING
ARNING Risk of accident due to
improper workon two-w ayradios
If two-w ayradios are manipulated or retro/t-
ted incor rectl y,the electromagnetic radiation
from the two-w ayradios can inter fere with the
ve hicle elect ronics and jeopardise the operat-
ing saf ety of theve hicle. #
You should ha veall workon electrical
and electronic components car ried out
at a quali/ed specialist workshop. &
W
WARNING
ARNING Risk of accident due to
improper operation of two-w ayradios
If yo u use two-w ayradios in theve hicle
improper ly,th eir electromagnetic radiation
can disrupt theve hicle's elect ronics. This is
th e case in thefo llowing situations, in particu-
lar: R
The two-w ayradio is not connected toan
ex terior aerial.
R The exterior aerial is /tted incor rectly or is
not a lo w-re0ection aerial.
This could jeopardise the operating saf ety of
th eve hicle. #
Have the lo w-re0ection exterior aerial /t-
ted at a quali/ed specialist workshop. #
When operating two-w ayradios in the
ve hicle, alw ays connect them tothe lo w-
re 0ection exterior aerial. *
N
NOOTE
TE Inva lidation of the operating permit
due tofailure tocomply with the inst ruc-
tions for installation and use The operating permit may be in
validated if the
inst ructions for installation and use of two-w ay
ra dios are not obser ved. #
Only use appr oved frequency bands. #
Obser vethe maximum permissible out-
put po wer in these frequency bands. #
Only use appr oved aerial positions. 348
348
Te
ch nical data

There are no
restrictions when positioning the
aerial on the outside of theve hicle forth efo llo w-
ing frequency bands:
R Terrestrial Trunked Radio (TETRA)
R 70 cm frequency band
R 2G/3G/4G R
R
egulat
egulat or
ory r
y r adio
adio identi/cation
identi/cation and not
and notes
es R
R
egulat
egulat or
ory r
y r adio
adio identi/cation
identi/cation of small com
of small compo-
po-
nents
nents Manufacturer information about
radio-based vehi-
cle components can be found using thekey
phrase "Regulatory radio identi/cation" in the Dig-
ital Owner's Manual in theve hicle, on the internet
and in the app. R
R
egulat
egulat or
ory r
y r adio
adio identi/cation
identi/cation – Indonesia and
– Indonesia and
Isr
Isr ael
ael Manufacturer information about
radio-based vehi-
cle components for Indonesia and Israel can be
fo und using theke y phrase "Regulatory radio iden-
ti/cation – Indonesia and Israel" in the Digital Owner's Manual in
theve hicle, on the internet
and in the app.
% These are not small components. Information
about small components can be found using
th eke y phrase "Regulatory radio identi/cation
of small components". F F
urt
urt her
her com
com ponent-speci/c
ponent-speci/c inf
infor
ormation
mation Fu
rther component-speci/c information can be
fo und using theke y phrase "fur ther component-
speci/c information" in the Digital Owner's Man-
ual in theve hicle, on the internet and in the app. V
V
ehicle
ehicle identi/cation
identi/cation plat
plate, VIN and engine num-
e, VIN and engine num-
ber ov
ber overerview
view
V
V ehicle
ehicle identi/cation
identi/cation plate
plate 350
350
Te
ch nical data

VIN belo
VIN belo
w t
w the fr
he fr ont r
ont r ight-hand seat
ight-hand seat 1
Imprinted VIN (vehicle identi/cation number)
2 Floor co vering VIN at t
VIN at t he low
he lower edg
er edge of t
e of the windscr
he windscr een
een 1
VIN (vehicle identi/cation number) as label
The VIN as a label at the lo wer edge of the wind-
screen is only available in some countries.
Engine number
Engine number
Fu rther information on mo tor numbers can be
obtained at a quali/ed specialist workshop. Oper Oper
ating
ating 0uids
0uids N
No
ot
tes on oper
es on oper ating
ating0uids
0uids &
W
WARNING
ARNING Risk of injury from operating
0uids harmful toyour health
Operating 0uids may be poisonous and harm-
ful toyour health. #
Obser vethete xt on the original contain-
ers when using, storing or disposing of
operating 0uids. #
Always store operating 0uids sealed in
th eir original containers. #
Alwayske ep children away from operat-
ing 0uids. +
ENVIR ENVIR
ONMENT
ONMENT AL NO
AL NOTE
TEPollution of the
environment due toirre sponsible disposal
of operating 0uids Incor
rect disposal of operating 0uids can
cause considerable damage tothe environ-
ment. 352 352
Te
ch nical data

#
Dispose of operating 0uids in an environ-
mentally responsible manner. Operating 0uids include
thefo llowing:
R lubricants
R coolant
R Brake 0uid
R windscreen washer 0uid
R climate cont rol system refrigerant
Only use products appro vedby Mercedes-Benz.
Damage caused bythe use of products that ha ve
not been app rove d is not co veredby the
Mercedes-Benz warranty or goodwill gestu res.
Yo u can identify operating 0uids appr ovedby
Mercedes-Benz bythefo llowing inscriptions on
th e container:
R MB-F reigabe (e.g. MB-F reigabe 229.51)
R MB-Appr oval (e.g. MB -Appr oval 229.51) Fu
rther information on appr oved operating 0uids
is available at thefo llowing locations:
R inthe Mercedes-Benz Speci/cations for Oper-
ating Fluids byentering the designation
- at https://be vo.mercedes-benz.com
- inthe Mercedes-Benz BeVo App
R Ataqu ali/ed specialist workshop N
No
ot
tes on br
es on br ak
ake
e0uid
0uid Obser
vethe no tes on operating 0uids
(/ page 352). &
W
WARNING
ARNING Risk of an accident due to
va pour poc kets form ing in the brake sys-
tem
The brake 0uid constantly absorbs moisture
from the air. This lo wersthe boiling point of
th e brake 0uid. If the boiling point is too lo w,
va pour poc kets may form inthe brake system
when the brakes are applied hard.
This impairs the braking e.ect. #
Have the brake 0uid rene we d at the
speci/ed inter vals. Ha
ve the brake 0uid regula rly re placed at a quali-
/ed specialist workshop.
Only use a brake 0uid appr ovedby Mercedes-
Benz according toMB-F reigabe or MB-Appr oval
331.0. Coolant
Coolant
N
No
ot
tes on coolant
es on coolant
Obser vethe no tes on operating 0uids
(/ page 352). &
W
WARNING
ARNING Risk of /re‑ and injury from
antif reeze
If antifreeze comes into contact with hot com-
ponent parts in the engine compartment, it
may ignite. #
Allow the drive system tocool down
before youto p up the antifreeze. #
Make sure that no antif reeze spills out
next tothe /ller opening. Te
ch nical data
353
353

#
Tho roughly clean the antifreeze from
component parts before starting the
ve hicle. *
N
NOOTE
TE Damage caused byincor rect cool-
ant #
Only use coolant that has been premixed
with there qu ired antifreeze pr otection.
Information on coolant is available at thefo l-
lowing locations:
R Inthe Mercedes-Benz Speci/cation for
Operating Fluids 320.1
- Athttps://be vo.mercedes-benz.com
- Inthe Mercedes-Benz BeVo App
R Ataqu ali/ed specialist workshop *
N
NOOTE
TE Overheating at high outside temp er-
atures If an inappropriate coolant is used,
the cooling
system is not su1ciently pr otected against
ov erheating and cor rosion at high outside
te mp eratures. #
Only use coolant appr ovedfor
Mercedes-Benz. #
Obser vethe inst ructions in the
Mercedes-Benz Speci/cations for Oper-
ating Fluids 320.1. Ha
ve the coolant regula rly re placed at a quali/ed
specialist workshop.
Proportion of antif reeze concentrate in the engine
cooling system:
R A minimum of 50% (antifreeze pr otection down
to about -37°C)
R A maximum of 55% (antif reeze pr otection
down to-45°C) N
No ot
tes on windscr
es on windscr een w
een washer
asher 0uid
0uid Obser
vethe no tes on operating 0uids
(/ page 352). &
W
WARNING
ARNING Risk of /re and injury from
windscreen washer concent rate
Wi ndsc reen washer concent rate is highly 0am-
mable. If it comes into contact with hot com-
ponents, it may ignite. #
Make sure that windscreen washer con-
cent rate is not spilled near tothe /ller
opening. *
N NOOTE
TE Damage totheex terior lighting due
to unsuitable windscreen washer 0uid Unsuitable windscreen
washer 0uids may
damage the plastic sur face of theex terior
lighting. #
Only use windscreen washer 0uids which
are also suitable for use on plastic sur fa-
ces, e.g. MB SummerFit or MB WinterFit. 354
354
Te
ch nical data

Displa
Displa
y messag
y messag es P
es Possible causes/conseq
ossible causes/consequences and uences andM
MSolutions
Solutions
Á
Key not detected (white dis-
play message) *T
hekey is cur rently unde tected. #
Change the location of theke y in theve hicle. #
Ifth eke y is still not recognised, place it in the slot for starting with theke y (/ page 154).
Á Key not detected (red dis-
play message) *T
hekey cann otbe de tected and may no longer be in theve hicle.
If th eke y is no lon ger in theve hicle and you switch o. theve hicle:
R You can no longer start theve hicle.
R You cannot centrally lock theve hicle. #
Ensu rethat theke y is in theve hicle.
If th eke y is in theve hicle and still not recognised: #
Stop theve hicle immediately in accordance with the tra1c conditions. #
Place theke y in the slot for starting the engine with theke y (/ page 154).
The key battery is weak or dischar ged. #
Check the battery using the indicator lamp (/ page 74). #
Replace theke y batter y,if necessary (/ page 76). Display message
s andwarning/indicator lamps
365
365