seat MERCEDES-BENZ GL550 2008 X164 Workshop Manual

118 Controls in detail
Locking and unlocking

If the SmartKey with KEYLESS-GO is
removed from the vehicle (e.g. if a
passenger exits the vehicle with the
SmartKey with KEYLESS-GO)

when pressing the KEYLESS-GO
start/stop button or trying to lock
the vehicle with the look button on
an outside door handle the mes-
sage
Key Not Detected appears in
the multifunction display

with the engine running, the mes-
sage
Key Not Detected appears in
the multifunction display while
driving off.
Find the SmartKey with KEYLESS-GO or
change its present location immediate-
ly (e.g. place it on the front passenger
seat or insert it in shirt pocket).

Remember that the engine can be
started by anyone with a SmartKey
with KEYLESS-GO that is left inside the
vehicle.
Possibility 1 (One SmartKey with
KEYLESS-GO in the vehicle, one
SmartKey with KEYLESS-GO outside
the vehicle):
If you leave the SmartKey with
KEYLESS-GO behind when exiting and
locking the vehicle, no message
appears in the multifunction display.
Possibility 2 (One SmartKey with
KEYLESS-GO in the vehicle, no
SmartKey with KEYLESS-GO outside
the vehicle):
When exiting and trying to lock the
vehicle, the message
Key Detected In
Vehicle
will appear in the multifunction
display. The vehicle will not be locked.Factory setting
Global unlocking
Grasp an outside door handle.
All turn signal lamps flash once. The
locking knobs in the doors move up.
The anti-theft alarm system is dis-
armed.
The vehicle will lock again automatically
and rearm the anti-theft alarm system
within approximately 40 seconds of
unlocking if

neither a door nor the tailgate is
opened

the central locking switch is not
activated
iThe vehicle could be inadvertently unlocked
if the SmartKey with KEYLESS-GO is within 3 ft
(1 m) of the vehicle and

an outside door handle is splashed with
water
or

you attempt to clean an outside door handle
164.boo Seite 118 Freitag, 30. März 2007 12:54 12

122 Controls in detail
Locking and unlocking
Tailgate
Opening the tailgate from the outside
The handle is located above the rear
license plate recess.
Pull on the handle.
The tailgate opens slightly.
Pull tailgate upwards to open.Opening the tailgate from the inside
You can unlock the tailgate from the
third-row seats and then open it manually.
The handle is located on the right of the
tailgate’s window trim.
1Handle
2Push
3Lift
Push handle1 in direction of
arrow2 and hold it there.
Lift handle1 in direction of arrow3.
The tailgate is released and can be
opened manually.
iVehicles without KEYLESS-GO*:
The vehicle must be unlocked (
page 40).iIf you do not open the tailgate within a few
seconds, the tailgate lock will automatically
engage again. Additionally, the tailgate will
relock automatically, if the vehicle was locked
when the tailgate was released from the inside.
If the tailgate lock does not engage automatically
and, if applicable, the tailgate does not relock
after a few seconds, you have to close the tail-
gate manually (
page 123).
164.boo Seite 122 Freitag, 30. März 2007 12:54 12

124 Controls in detail
Locking and unlocking
Opening the tailgate from the outside
You can unlock and open the tailgate
simultaneously from the outside when the
vehicle is at a standstill.
Press and hold buttonŠ on the
SmartKey or SmartKey with
KEYLESS-GO* until the tailgate unlocks
and opens.
While the tailgate is opening, an
acoustic signal sounds.
or
Vehicles with KEYLESS-GO*:
Pull on the handle (
page 122).
The tailgate is unlocked and opens.
While the tailgate is opening, an acous-
tic signal sounds.Opening the tailgate from the inside
You can unlock and open the tailgate si-
multaneously from the driver’s seat when
the vehicle is at a standstill.The switch is located in the driver’s door.
1Remote tailgate switch
Pull remote tailgate switch1 until
tailgate begins to open.
The tailgate opens. While the tailgate is
opening, an acoustic signal sounds.
Warning!G
Maintain sight of the area around the rear of
the vehicle while operating the tailgate with
the door-mounted remote tailgate switch or
with the Šbutton on the SmartKey or
SmartKey with KEYLESS-GO*. Monitor the
opening procedure carefully to make sure
no one is in danger of being injured.
To interrupt the opening procedure, press or
pull the door-mounted remote tailgate
switch or press the Šbutton on the
SmartKey or SmartKey with KEYLESS-GO*.
164.boo Seite 124 Freitag, 30. März 2007 12:54 12

130 Controls in detail
Seats
For information on seat adjustment, see
the “Getting started” section (
page 45).
For more information on seats, see “Load-
ing” (
page 295).
Easy-entry/exit feature for third-row
seats
This feature allows for easier access to and
exit from the vehicle’s third-row seats.Easy-entry feature for third-row seats
The lever for the easy-entry feature is lo-
cated on the rear of the seat base of the
passenger side second-row seat.
1Easy-entry lever
Pull and hold easy-entry lever1 in di-
rection of arrow at resistance point.
The seat backrest folds forward.1Easy-entry lever
Pull and hold easy-entry lever1 once
again in direction of arrow at resistance
point.
Lift up the right second-row seat until it
folds forward.
You should now have sufficient space
to access the vehicle’s third-row seat.
Warning!G
To help avoid personal injury, the
second-row seat backrests must be properly
locked either in the upright position or,
when using the expanded cargo compart-
ment, in the fully folded position while the
vehicle is in motion.
!Make sure that the head restraint is pushed
all the way down (
page 135).
iVehicles with memory function*:
The front passenger seat moved slightly forward.
164.boo Seite 130 Freitag, 30. März 2007 12:54 12

131 Controls in detail
Seats
Easy-entry/exit position
While the easy-entry feature is activated,
you will see, for example, the following
message in the multifunction display:
2nd Row Of Seats – Right
Not Locked
Return seat into its original position
(
page 132).
The message in the multifunction dis-
play disappears.For setting the front passenger seat back
into the stored position, see “Recalling po-
sitions from memory” (
page 142).
For information on how to fold down the
second-row seats completely, see “Folding
second-row seats” (
page 306).
Easy-exit feature for third-row seats
The easy-exit strap is located on the right
rear of the second-row seat base.
1Easy-exit strap
To exit the vehicle when seated on a
third-row seat, pull up and hold
easy-exit strap1.
The right second-row seat backrest
folds forward.
Pull and hold once easy-entry strap1.
Lift up the right second-row seat until it
folds forward.
You should now have sufficient space
to exit the vehicle’s third-row seat.
While the easy-entry feature is activated,
you will see, for example, the following
message in the multifunction display:
2nd Row Of Seats – Right
Not Locked
iVehicles with memory function*:
The front passenger seat moved slightly forward.

164.boo Seite 131 Freitag, 30. März 2007 12:54 12

132 Controls in detail
Seats
Return seat into its original position
(
page 132).
The message in the multifunction dis-
play disappears.
For setting the front passenger seat back
into the stored position, see “Recalling po-
sitions from memory” (
page 142).
For information on how to fold down the
second-row seats completely, see “Folding
second-row seats” (
page 306).
Returning second-row seats to their
original positionFold seat (page 131) back until it au-
dibly engages.
Fold seat backrest (page 130) back
into original position until it engages.
To make sure the seat backrest has en-
gaged, lean firmly against the backrest.Emergency exit for third-row seats
1Emergency release
2Seat backrest
Warning!G
When occupants have entered or exited the
vehicle using the easy-entry/exit feature,
before driving off make sure

the seats are properly locked

the seat backrests are in an upright po-
sition and are properly locked
If a seat and seat backrest are not properly
locked, the seat could move forward and the
seat backrest could fold. You could slide un-
der the seat belt during braking, vehicle ma-
neuvers, or in an accident. If you slide under
it, the belt would apply force at the abdomen
or neck. That could cause serious or even fa-
tal injuries.
iIf, due to an accident or other situation, it is
not possible for you to exit the vehicle on the
side of the easy-entry seat (
page 130), you
can fold the left side of the seat backrest in the
second row of seats down in order to open the
left rear door.
!Make sure that the head restraint is pushed
all the way down (
page 135).

164.boo Seite 132 Freitag, 30. März 2007 12:54 12

133 Controls in detail
Seats
Pull emergency release1 in the
direction of arrow.
Push seat backrest2 forwards.
Open the left door.
Exit the vehicle.
Front seat active head restraints
You cannot remove the active head
restraints on the driver’s and front
passenger’s seat.
For removal of the active head restraints
we recommend that you contact an
authorized Mercedes-Benz Light Truck
Center.
For information on head restraint adjust-
ment, see “Seats” (
page 45).
For information on active head restraints,
see “Active head restraint” (
page 90).
Rear seats
Warning!G
To help avoid personal injury when folding
the seat backrest forward, make sure that
you move both feet and legs all the way back
and out of the way to avoid them contacting
the seat as it pivots forward.
In order to prevent an accident or any other
potentially dangerous situations when open-
ing the rear door and exiting the vehicle,
make sure that you are aware of the traffic
situation at all times.
Warning!G
For your protection, drive only with properly
positioned head restraints.
Adjust the head restraint so that it is close
to the head as possible and the center of the
head restraint supports the back of the head
at eye level. This will reduce the potential for
injury to the head and neck in the event of
an accident or similar situation.
Warning!G
According to accident statistics, children
are safer when properly restrained in the
rear seating positions than in the front seat-
ing position. Thus, we strongly recommend
that children be placed in the rear seats.
Regardless of seating position, children
12 years old and under must be seated and
properly secured in an appropriately sized
infant restraint, toddler restraint, or booster
seat recommended for the size and weight
of the child. For additional information, see
“Children in the vehicle” (
page 91).
A child’s risk of serious or fatal injuries is
significantly increased if the child restraints
are not properly secured in the vehicle
and/or the child is not properly secured in
the child restraint.
164.boo Seite 133 Freitag, 30. März 2007 12:54 12

134 Controls in detail
Seats
Rear seat adjustment
Seat backrest tilt (second-row seats)The seat backrest tilt can be set to five
different positions.
The handles for adjusting the seats are
located on the rear of each seat base.
1Adjustment handle
While seated, pull handle1 in direc-
tion of arrow to resistance point and
hold it there.
To move seat backrest back, lean light-
ly against backrest.
Warning!G
Never ride in a moving vehicle with the seat
backrest in an excessively reclined position
as this can be dangerous. You could slide
under the seat belt in a collision. If you slide
under it, the belt would apply force at the ab-
domen or neck. That could cause serious or
fatal injuries. The seat backrest and seat
belts provide the best restraint when the
wearer is in a nearly upright position and
belts are properly positioned on the body.
Your seat must be adjusted so that you can
correctly fasten your seat belt (
page 53).
Never place hands under the seat or near
any moving parts while a seat is being
adjusted.
After adjusting rear seats, make sure

the seats are properly locked

the seat backrests are in an upright po-
sition and are properly locked
Check for secure locking by pushing and
pulling on the seat backrests. If a seat and
seat backrest are not properly locked, the
seat could move forward and the seat back-
rest could fold. The child seat would no long-
er be properly supported or positioned to
provide its intended benefit.
Warning!G
The seat belt only offers its intended protec-
tion when the seat backrest is in a nearly
vertical position and the occupant is sitting
upright. Avoid sitting in positions that pre-
vent the seat belt from being properly posi-
tioned against the body (
page 53). You
should therefore adjust the backrest to a po-
sition as upright as possible.
164.boo Seite 134 Freitag, 30. März 2007 12:54 12

135 Controls in detail
Seats
To move seat backrest forward, lean
forward with handle1 pulled and held
at resistance point.
The seat backrest will move forward
against your back.
Release handle1 when the seat back-
rest has reached the desired position.
To make sure the seat backrest has en-
gaged, lean firmly against the backrest.
Head restraint height
Second-row seat head restraint
1Head restraint
2Release buttonRaising:
Manually adjust the height of head
restraint1 by pulling it upward to the
desired position.
Lowering:
To lower head restraint1, push
release button2 and press down on
head restraint1.
Warning!G
With a rear seat occupied, make sure to
move the respective head restraint up from
the lowest non-use position and have the oc-
cupant adjust the head restraint properly.
For your protection, drive only with properly
positioned head restraints.
Adjust the head restraint in such a way that
it is as close to the head as possible and the
center of the head restraint supports the
back of the head at eye level. This will re-
duce the potential for injury to the head and
neck in the event of an accident or similar
situation.
iThe third-row seat head restraints are ad-
justed in the same manner.
164.boo Seite 135 Freitag, 30. März 2007 12:54 12

136 Controls in detail
Seats
Head restraint fore and aft adjustment
The angle of the head restraint for the out-
er second-row seats or the third-row seats
can be adjusted manually.
While seated, reach behind you with
both hands and find lower edge of the
head restraint.
Adjust the head restraint to the desired
position by pushing or pulling on the
lower edge of the head restraint cush-
ion.Head restraints
Second-row seat head restraint
1Head restraint
2Release button
Removing
Second-row seat:
Fold the seat backrest forward
(
page 134).
Third-row seat:
Fold the seat backrest forward
(
page 305).
Pull head restraint1 to its uppermost
position.
Warning!G
Do not drive the vehicle without the seat
head restraints installed when the rear seats
are occupied. Head restraints are intended
to help reduce injuries during an accident.
With a rear seat occupied, make sure to
move the respective head restraint up from
the lowest non-use position and have the oc-
cupant adjust the head restraint properly.
For your protection, drive only with properly
positioned head restraints.
Adjust the head restraint in such a way that
it is as close to the head as possible and the
center of the head restraint supports the
back of the head at eye level. This will re-
duce the potential for injury to the head and
neck in the event of an accident or similar
situation.
164.boo Seite 136 Freitag, 30. März 2007 12:54 12