buttons MERCEDES-BENZ S-Class 2008 W221 Comand Manual

554 Controls in detailUseful featuresIf you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:
Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been successful-
ly trained.

While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
button6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this se-
quence on the hand-held remote con-
trol until the frequency signal has been
learned. Upon successful training, indi-
cator lamp1 will flash slowly and then
rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete.Reprogramming a single signal trans-
mitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Switch on the ignition (
page 370).

Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.

Indicator lamp1 will begin to flash af-
ter 20 seconds. Without releasing the
signal transmitter button, proceed with
programming starting with step 3.Operation of integrated remote control

Switch on the ignition (
page 370).

Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing integrated remote control
memory

Switch on the ignition (
page 370).

Simultaneously press and hold outer
signal transmitter buttons2 and 4,
for approximately 20 seconds, until
indicator lamp1 flashes rapidly. Do
not hold for longer than 30 seconds.
The codes of all three channels are
erased.
i
Upon completion of programming the inte-
grated remote control, make sure you retain the
hand-held remote control that came with the ga-
rage door opener, gate operator or other device.
You may need it for use in other vehicles, for fu-
ture programming of an integrated remote con-
trol, or simply for continued use as a hand-held
remote control to operate the respective device
in other situations.
i
If you sell your vehicle, erase the codes of all
three channels.

778 IndexChildren in the vehicle 58
Air bags 58
Indicator lamp front passenger
front air bag off 51, 640
Infant and child restraint systems 59
LATCH-type child seat anchors 63
Override switch for rear passenger
compartment 64
Tether attachment points 62
Chrome-plated exhaust tip*,
Cleaning 625
Cigarette lighter 537
Cockpit 26
COMAND
Adjusting volume 98
Audio AUX 129
Components 87
Controller 90
Display 88
Display illumination 89
Function buttons 88
Main menus 98
Menu overview 92
Navigation system 188
Operating 92Operating safety 86
Operating seats 282
Phone book* 158
Radio, FM/AM 102
Selecting sound settings 99
SMS messages 183
Surround sound 100
Switching off/on the
audio source 101
Switching on or off 87
Swiveling display 89
System settings 259
Telephone keypad* 90
Telephone menu* 141
Vehicle menu 264
Voice Control settings 261
Combination switch 403
Corner-illuminating lamps 404
High beam flasher 403
Turn signals 420
Windshield wipers 408
Command list (Voice Control) 340
Address book commands 345
Audio commands 347
General commands 340Navigation commands 343
Telephone* commands 341
Control system instrument cluster 287
Multifunction display 287
Multifunction steering wheel 288
Control system instrument cluster menus
AMG 296
Assistance* 303
Audio 294
Navi 292
Service 304
Settings 305
Telephone* 299
Trip 291
Vehicle status message memory 304
Coolant 579
Adding 580
Anticorrosion/antifreeze mixing
ratio and quantity 771
Checking level 579
Messages in display 679
Temperature 569
Temperature gauge 29, 444
Coolant level
Checking 579
Corner-illuminating lamps 404