warning MERCEDES-BENZ SLC 2017 Owners Manual

X
Pull the tire sealant bottle out of the tire infla-
tion compressor.
The filler hose remains attached to the tire
sealant bottle. X
Drive to the nearest qualified specialist work-
shop and have the tire changed there. X
Have the tire sealant bottle and the filler hose
replaced as soon as possible at aq ualified
specialist workshop. X
Have the tire sealant bottle replaced every
four years at aq ualified specialist workshop.
Battery (vehicle)
Important safety notes Special tools and expert knowledge are required
when working on the battery, e.g. removal and
installation .Y ou should therefore have all work
involvin gt he battery carried out at aq ualified
specialist workshop.
G WARNING
Work carried out incorrectly on the battery
can lead, for example, to as hort circuit and
thus damage the vehicle electronics. This can
lead to function restriction sa pplying to
safety-relevant systems, e.g the lighting sys-
tem, the ABS (anti-loc kb raking system) or the
ESP ®
(Electronic Stability Program). The oper-
ating safety of your vehicle may be restricted.
You could lose control of the vehicle, for
example: R
when braking R
in the event of abrupt steerin gm aneuvers
and/or when the vehicle's speed is not
adapted to the road conditions
There is ar isk of an accident.
In the event of as hort circuit or as imilar inci-
dent, contact aq ualified specialist workshop
immediately. Do not drive any further .Y ou
should have all work involvin gt he battery car-
ried out at aq ualified specialist workshop.
For further information about ABS and ESP ®
,
see ( Y
page 55) and ( Y
page 58). G WARNING
Electrostatic build-up can lead to the creation
of sparks, which could ignite the highly explo-
sive gases of ab attery. There is ar isk of an
explosion.
Before handling the battery, touch the vehicle
body to remove any existin ge lectrostatic
build-up.
The highly flammable gas mixture forms when
charging the battery as well as when jump-start-
ing.
Always make sure that neither you nor the bat-
tery is electrostatically charged. Ab uild-up of
electrostatic charge can be caused, for exam-
ple: R
by wearing clothin gm ade from synthetic
fibers R
due to friction between clothin ga nd seatsR
if you push or pull the battery across the car-
pet or other synthetic materials R
if you wipe the battery with ac loth
G WARNING
During the charging process, ab attery produ-
ces hydrogen gas. If as hort circuit occurs or
sparks are created, the hydrogen gas can
ignite. There is ar isk of an explosion. R
Make sure that the positive terminal of a
connected battery does not come into con-
tact with vehicle parts. R
Never place metal object sort ools on ab at-
tery. R
It is importan tt hat you observe the descri-
bed order of the battery terminals when
connectin ga nd disconnectin gab attery.R
When jump-starting, make sure that the
battery poles with identical polarity are
connected. R
It is particularly importan ttoo bserve the
described order when connectin ga nd dis-
connectin gt he jumper cables. R
Never connect or disconnect the battery
terminals while the engine is running.
G WARNING
Battery acid is caustic. There is ar isk of injury.246
Battery (vehicle)
Breakdown assistance

The vehicle will then use very little energy, thus
conserving battery power.
If the power supply has been interrupted, e.g. if
you reconnect the battery, you will have to: R
reset the function for automatically folding
the exterior mirrors in/out by folding the mir-
rors out once ( Y
page 89)R
set the clock (see the Digital Operator's Man-
ual)
On vehicles with am ultimedia system, the
time is set automatically.
Charging the battery
G WARNING
During charging and jump-starting, explosive
gases can escape from the battery. There is a
risk of an explosion.
Particularly avoid fire, open flames, creating
sparks and smoking. Ensure there is sufficient
ventilation while charging and jump-starting.
Do not lean over ab attery.
G WARNING
Battery acid is caustic. There is ar isk of injury.
Avoid contact with skin, eyes or clothing. Do
not inhale any battery gases. Do not lean over
the battery. Keep children away from batter-
ies. Wash away battery acid immediately with
plenty of clean water and seek medical atten-
tion.
G WARNING
Ad ischarged battery can freeze at tempera-
tures below freezin gp oint. When jump-start-
ing the vehicle or charging the battery, gases
can escape from the battery. There is ar isk of
an explosion.
Allow the frozen battery to thaw out before
charging it or jump-starting.
! Only use battery chargers with am aximum
charging voltage of 14.8 V.
! Only charge the battery using the jump-
starting connection point.
The jump-starting connection point is in the
engine compartment. If the indicator/warning lamps do not light up at
low temperatures, it is very likely that the dis-
charged battery has frozen. In this case, you
may neither charge the battery nor jump-start
the vehicle. The service life of at hawed-out bat-
tery may be shorter .T he starting characteristics
can be impaired, particularly at low tempera-
tures. Have the thawed-out battery checked at a
qualified specialist workshop.
Read the battery charger's operating instruc-
tions before charging the battery. X
Open the hood. X
Connec tt he battery charger to the positive
terminal and ground point in the same order
as when connectin gt he donor battery in the
jump-starting procedure ( Y
page 249).248
Battery (vehicle)
Breakdown assistance

Jump-starting For the jump-starting procedure, use only the jump-starting connection point in the engine com-
partment ,c onsisting of ap ositive terminal and ag round point.
G WARNING
Battery acid is caustic. There is ar isk of injury.
Avoid contact with skin, eyes or clothing. Do not inhale any battery gases. Do not lean over the
battery. Keep children away from batteries. Wash away battery acid immediately with plenty of
clean water and seek medical attention.
G WARNING
During charging and jump-starting, explosive gases can escape from the battery. There is ar isk
of an explosion.
Particularly avoid fire, open flames, creating sparks and smoking. Ensure there is sufficient ven-
tilation while charging and jump-starting. Do not lean over ab attery.
G WARNING
During the charging process, ab attery produces hydrogen gas. If as hort circuit occurs or sparks
are created, the hydrogen gas can ignite. There is ar isk of an explosion.R
Make sure that the positive terminal of ac onnected battery does not come into contact with
vehicle parts. R
Never place metal objects or tools on ab attery.R
It is important that you observe the described order of the battery terminals when connecting
and disconnecting ab attery.R
When jump-starting, make sure that the battery poles with identical polarity are connected. R
It is particularly important to observe the described order when connecting and disconnecting
the jumper cables. R
Never connect or disconnec tt he battery terminals while the engine is running.
G WARNING
Ad ischarged battery can freeze at temperatures below freezing point. When jump-starting the
vehicle or charging the battery, gases can escape from the battery. There is ar isk of an explosion.
Allow the frozen battery to thaw out before charging it or jump-starting.
! Avoid repeated and lengthy starting attempts. Otherwise, the catalytic converter could be
damaged by the non-combusted fuel.
If the indicator/warning lamps do not light up at low temperatures, it is very likely that the dis-
charged battery has frozen .Int his case, you may neither charge the battery nor jump-start the
vehicle. The service life of at hawed-out battery may be shorter. The starting characteristic sc an be
impaired, particularly at low temperatures. Have the thawed-out battery checked at aq ualified
specialist workshop. Jump-starting 249
Breakdown assistance Z

wise be locked out when pushin gort owing the
vehicle.
Installing/removing th et owing eye
Installing th et owing eye
G WARNING
The exhaust tail pipe may be ver yh ot .T her ei s
ar isk of burn sw hen removin gt he rear cover.
Do not touc ht he exhaust pipe. Take particular
car ew hen removin gt he rear cover.
The bracket sf or th es crew-in towing eye are
located in th eb umpers. They are at th ef ront and
at th er ear ,b ehin dt he covers.X
Remov et he towing eye fro mt he vehicle tool
kit ( Y
page 241).X
Pres st he mark on cover C inwards in the
directio noft he arrow.X
Take cover C off th eo pening.X
Screw in th et owing eye clockwis easf ar as it
will go and tighten it.
Removing th et owing eyeX
Unscrew and remove th et owing eye.X
Attac hc over C to th eb umper and pres su ntil
it engages. X
Place th et owing eye in th ev ehicle too lk it. Towing av ehicle with both axles on
th eg round
G WARNING
You can no longer steer th ev ehicle if the
steerin gw heel lock has been engaged. There
is ar isk of an accident.
Always switch off th ei gnitio nw hen towing the
vehicle with at ow cable or at ow bar.
The automatic transmission automatically shifts
to position P when you open th ed river's or front-
passenger door or when you remove th eS ma rt-
Key fro mt he ignitio nl ock.
In orde rtoe nsure that th ea utomatic transmis-
sion stays in position N when towing th ev ehicle,
you must observe th ef ollowing points:X
Switch on th eh azar dw arning lamps
( Y
page 95). X
Turn th eS ma rtKey to position 2 in th ei gnition
lock.
On vehicles with KEYLESS-GO, use th eS ma rt-
Key instead of th eS ta rt/Stop button
( Y
page 115). X
Depress and hold th eb rak ep edal.X
Shif tt he transmission to position N .X
Release th eb rak ep edal.X
Release th ee lectric parking brake. X
Leave th eS ma rtKey in position 2 in th ei gni-
tio nl ock.
In orde rtos ignal ac hange of directio nw hen
towing th ev ehicle with th eh azar dw arning
lamps switche do n, use th ec ombination switch
as usual. In this case ,o nly th ei ndicator lamps
for th ed irectio noft ra vel flash .W hen you reset
th ec ombination switch, th eh azar dw arning
flashers start flashing again.
It is importan tt ha ty ou observe th es afety
instructions when towing away your vehicle
( Y
page 251).
Towing th ev ehicle with th er ea ra xle
raised
! The ignitio nm ust be switche do ff if you are
towing th ev ehicle with th er ear axle raised.
Interventio nbyE SP ®
could otherwise dam-
age th eb rak es ystem.252
Towing and tow-starting
Breakdown assistance

! Vehicles with automatic transmission must
not be towed with the rear axle raised. The
vehicle/trailer combination may otherwise
swerve or even roll over.
Transporting the vehicle
Vehicle sw ith automatic transmission
! When the vehicle is loade df or transport, the
front and rear axles must be stationary and on
the same transportation vehicle. Positioning
over the connection point of the transport
vehicle is not permitted. The drive train may
otherwise be damaged.
All vehicles
! You may only secure the vehicle by the
wheels, not by parts of the vehicle such as
axle or steering components. Otherwise, the
vehicle could be damaged.
The towing eye can be used to pull the vehicle
onto at railer or transporter for transporting pur-
poses. X
Turn the SmartKey to position 2 in the ignition
lock. X
Shift the transmission to position N .
As soon as the vehicl eh as been loaded:X
Prevent the vehicle from rolling awa yb y
applying the electric parking brake. X
Shift the transmission to position P .X
Turn the SmartKey in the ignition lock to posi-
tion 0 and remove the SmartKey from the
ignition lock. X
Secure the vehicle. Tow-starting (emergenc ye ngine
starting)
! Vehicles with automatic transmission must
not be tow-started. You could otherwise dam-
age the automatic transmission.
You can find information on "Jump-starting" at
( Y
page 249).
Fuses
Important safety notes
G WARNING
If you manipulate or bridge af aulty fuse or if
you replace it with af use with ah igher amper-
age, the electric cables could be overloaded.
This could result in af ire. There is ar isk of an
accident and injury.
Alway sr eplace faulty fuses with the specified
new fuses having the correct amperage.
Blown fuses must be replaced with fuses of the
same rating, which you can recognize by the
color and value .T he fuse ratings are listed in the
fuse allocation chart.
The fuse allocation chart is located in the vehicle
tool kit in the stowage compartment under the
trunk floor ( Y
page 241).
If an ewly inserted fuse also blows, have the
cause traced and rectified at aq ualified special-
ist workshop, e.g. an authorized Mercedes-Benz
Center.
! Only use fuses that have been approved for
Mercedes-Benz vehicles and which have the
correct fuse rating for the system concerned.
Otherwise, component sors ystems could be
damaged.
! Make sure that no moisture can enter the
fuse box when the cover is open.
! When closing the cover, make sure that it is
lying correctly on the fuse box. Moisture seep-
ing in or dirt could otherwise impair the oper-
ation of the fuses.
The fuses in your vehicle serve to close down
faulty circuits. If af use blows, all the compo-
nent sont he circuit and their functions stop
operating. Fuses 253
Breakdown assistance Z

Before changin gaf useX
Switch off the engine. X
Switch off al le le ctrical consumers.X
Make sure tha tt he ignition is switched off
( Y
page 115).
or X
Whe nu si ng the SmartKey, turn the SmartKey
to position 0 in the ignition lock and remove it
( Y
page 115).X
Secure the vehicl ea gain st rolling away
( Y
page 131).
All indicator lamps in the instrument cluster
must be off.
The fuses are locate dinv arious fus eb ox es:R
Fus eb ox in the engine compartment on the
left-hand side of the vehicle, when viewe di n
the direction of travel R
Fus eb ox in the trunk
Fuse bo xint he engine compartment
i Observ et he "Important safety notes "s ec-
tio n( Y
page 253).
G WARNING
Whe nt he hoo diso pe na nd the windshield
wipers are set in motion, yo uc an be injured by
the wipe rl in kage. There is ar is kofi njury.
Alway ss wi tch off the windshield wipers and
the ignition before opening the hood.
X
Make sure tha tt he windshield wipers are
turne do ff.X
Ope nt he hood.X
Use ad ry cloth to remove any moisture from
the fus eb ox . X
To open: open clamps D .X
Remove fus eb ox cover C forwards.X
To close: check whethe rt he sea lisl yi ng cor-
rectl yinc over C .X
Insert cover C at the rea roft he fus eb ox into
the retainer. X
Fol dd ow nc over C and close clamps D .X
Close the hood.
Fuse bo xint he trunk
i Observ et he "Important safety notes "s ec-
tio n( Y
page 253).
The fus eb ox is locate dint he trunk behind the
partition covering. X
Ope nt he trunk lid. X
To open: release cover C on the right and
left-hand side sw it haf la to bj ect.X
Ope nc over C downward sint he direction of
the arrow.254
Fuses
Breakdo wn assis tance

MOExtended tires (tires with run-flat
properties) With MOExtended tires (tires with run flat char-
acteristics), you can continue to drive you rv ehi-
cle even if there is at otal loss of pressure in one
or more tires.
MOExtended tires may only be use dinc onjunc-
tion with an active tire pressure loss warning
system or with an active tire pressure monitor
and on wheels specifically tested by Mercedes-
Benz.
Notes on driving with MOExtended tires with a
flat tire ( Y
pag e2 42).
Vehicles equipped with MOExtended tires are
not equipped with aT IREFIT kit at the factory. It
is therefore recommende dt hat you additionally
equip you rv ehicl ew ith aT IREFIT kit if you mount
tires that do not feature run-fla tp roperties, e.g.
winter tires. AT IREFIT kit can be obtained from
aq ualified specialist workshop.
Winter operation
General notes Have you rv ehicl ew inter-proofed at aq ualified
specialist worksho patt he onset of winter.
Observe the notes in the "Changing aw heel"
section ( Y
pag e2 74).
Driving with summer tires At temperatures below 45 ‡( +7 †), summer
tires lose elasticity and therefore traction and
braking power. Change the tires on you rv ehicle
to M+S tires .U sing summe rt ires at very cold
temperatures coul dc aus ec racks to form,
thereby damaging the tires permanently.
Mercedes-Benz cannot accept responsibility for
this type of damage.
G WARNING
Damaged tires can caus et ire inflation pres-
sure loss. As ar esult, you coul dl ose control of
you rv ehicle. There is ar isk of accident.
Check the tires regularl yf or signs of damage
and replace any damaged tires immediately. M+S tires
G WARNING
M+S tires with at ire tread depth of less than

To avoid hazardous situations: R
never install snow chains to the front
wheels R
alway si nstall snow chains in pairs to the
rear wheels.
For safety reasons, Mercedes-Benz recom-
mends that you only use snow chains that have
been specially approved for your vehicle by
Mercedes-Benz ,ora re of ac orresponding
standard of quality. For more information,
please contact aq ualified specialist workshop.
If you inten dtom ount snow chains, please bear
the following points in mind: R
Snow chains may not be mounted on all
wheel/tire combinations. Permissible wheel-
tire combinations ( Y
page 278).R
Only use snow chains when driving on roads
completely covered by snow. Remove the
snow chains as soon as possible when you
come to ar oad that is not snow-covered.R
Local regulations may restrict the use of snow
chains. Observe the appropriate regulations if
you wish to mount snow chains. R
Do not exceed the maximum permissible
speed of 30 mph (50 km/h).
You may wish to deactivate ESP ®
when pulling
away with snow chains installed ( Y
page 58).
You can thereby allow the wheels to spin in a
controlled manner ,a chieving an increased driv-
ing force (cutting action).
Information about driving with an emergency
spare wheel ( Y
page 279). Tire pressure
Tire pressur es pecifications
Important safety notes
G WARNING
Underinflated or overinflated tires pose the
following risks: R
the tires may burst, especially as the load
and vehicle speed increase. R
the tires may wear excessively and/or
unevenly, which may greatly impair tire
traction. R
the driving characteristics, as well as steer-
ing and braking, may be greatly impaired.
There is ar isk of an accident.
Follow recommended tire inflation pressures
and check the pressure of all the tires includ-
ing the spare wheel: R
monthly, at least R
if the load changes R
before beginning al ong journeyR
under different operating conditions, e.g.
off-road driving
If necessary, correc tt he tire pressure.
The data on the Tire and Loading Information
placard and tire pressure table shown here are
examples. Tire pressure specification sa re vehi-
cle-specific and may deviate from the data
shown here. The tire pressure specifications
that are valid for your vehicle can be found on
the Tire and Loading Information placard and
tire pressure table on the vehicle.
General notes The recommended tire pressures for the tires
mounted at the factor yc an be found on the
labels described here.
Operation with an emergency spar ew heel:
information on operation with an emergency
spare wheel can be found in the general notes in
the "Emergency spare wheel" section
( Y
page 280).
Further information on tire pressures can be
obtained at aq ualified specialist workshop.258
Tir ep re ssure
Wheels and tires

Avoi dt ire pressures tha ta re too high in al lt he
tires, including the spare wheel.
Overinflated tire sm ay :R
increase the braking distance R
adversel ya ffect handlingR
wear excessivel ya nd/or unevenlyR
have an adverse effect on rid ec omfortR
be more susceptibl etod amag e
Maximum tire pressures
C
Example: maximu mp er missibl et ire pres-
sure
Never exceed the maximu mp er missibl et ire
inflation pressure. Alway so bs erve the recom-
mended tire pressure for your vehicl ew he n
adjusting the tire pressure ( Y
page 258).
i The actual values for tire sa re vehicle-spe-
cifi ca nd ma yd ev iate from the values in the
illustration.
Checkin gt he tire pressures
Important safety notes Observ et he notes on tire pressure
( Y
page 258).
Informatio nona ir pressure for the tire sony ou r
vehicl ec an be found:R
on the vehicle's Tire and Loading Information
placard on the B-pillar R
on the tire pressure labe lont he fuel fille rf lapR
in the "Tire pressure" section Checkin gt ire pressure sm anuallyTo determine and set the correct tire pressure,
procee dasf ollows: X
Remove the valve cap of the tire tha ti stob e
checked. X
Press the tire pressure gaug es ecurel yo nto
the valve. X
Read the tire pressure and compar eittot he
recommende dv alue on the Tire and Loading
Informatio np la card or the tire pressure table
( Y
page 258). X
If the tire pressure is too low, increase the tire
pressure to the recommende dv alue.X
If the tire pressure is too high, release air. To
do so, press down the meta lp in in the valve,
using the tip of ap en for example. The nc heck
the tire pressure agai nu si ng the tire pressure
checker. X
Screw the valve cap onto the valve. X
Repeat thes es tep sf or the othe rt ires.
Tire pressure loss warning system
(Canada only)
General notes While the vehicl eisinm otion, the tire pressure
loss warning system monitors the set tire pres-
sure using the rotational speed of the wheels.
Thi se nables the system to detect significant
pressure loss in at ire .Ift he speed of rotatio no f
aw heel change sasa resul tofa loss of pressure,
ac orresponding warning message will appear in
the multifunctio nd is play.
Yo uc an recognize the tire pressure loss warning
by the Run Fla tI ndicator Active Press
'OK 'toR estart message which appear si n
the Serv. menu of the multifunctio nd is play.
Informatio nont he message display can be
found in the "Restarting the tire pressure loss
warning system "s ectio n( Y
page 262).
Important safety notes
The tire pressure warning system does not warn
yo uofani ncorrectly set tire pressure. Observe
the notes on the recommende dt ire pressure
( Y
page 258).
The tire pressure loss warning does not replace
the nee dtor egularly check the tire pressure. An
eve nl os sofp ressure on severa lt ire satt heTire pressure 261
Wheel sa nd tires Z

same time cannot be detected by the tire pres-
sure loss warning system.
The tire pressure monitor is not able to warn you
of as udden loss of pressure, e.g. if the tire is
penetrated by af oreign object. In the event of a
sudden loss of pressure, bring the vehicle to a
halt by braking carefully .A void abrupt steering
movements.
The function of the tire pressure loss warning
system is limited or delayed if: R
snow chains are mounted on your vehicle's
tires. R
road conditions are wintry. R
you are driving on sand or gravel. R
you adopt av ery sporty driving style (corner-
ing at high speeds or driving with high rates of
acceleration). R
you drive with ah eavy load.
Restarting the tire pressure loss warn-
ing system Restart the tire pressure loss warning system if
you have: R
changed the tire pressure R
changed the wheels or tires R
mounted new wheels or tires X
Before restarting, make sure that the tire
pressures are set properly on all four tires for
the respective operating conditions.
The recommended tire pressure can be found
on the Tire and Loading Information placard
on the B-pillar. Additionally, at ire pressure
table is attached to the fuel filler flap. The tire
pressure loss warning system can only give
reliable warnings if you have set the correct
tire pressure. If an incorrect tire pressure is
set, these incorrect values will be monitored. X
Also observe the notes in the section on tire
pressures ( Y
page 258).X
Make sure that the SmartKey is in position 2
in the ignition lock ( Y
page 115).X
Press the Y or e button on the steering
wheel to select the Serv. menu.X
Press the c or d button to select
Tire Pressure .X
Press the v button.
The Run Flat Indicator Active Press
'OK' to Restart message appears in the
multifunction display. If you wish to confirm the restart: X
Press the v button.
The Tire Pressure Now OK? message
appears in the multifunction display. X
Press the c or d button to select Yes .X
Press the v button.
The Run Flat Indicator Restarted mes-
sage appears in the multifunction display.
After at each-in period, the tire pressure loss
warning system will monitor the set tire pres-
sures of all four tires.
If you wish to cancel the restart: X
Press the 8 button.
or X
If the Tire Pressure Now OK? message
appears, use the c or d button to
select Cancel . X
Press the v button.
The tire pressure values stored at the last
restart will continue to be monitored.
Tire pressure monitor
General notes If at ire pressure monitor is installed, the vehi-
cle's wheels have sensors that monitor the tire
pressures in all four tires. The tire pressure mon-
itor warns you if the pressure drops in one or
more of the tires. The tire pressure monitor only
functions if the corresponding sensors are
installed in all wheels.
Information on tire pressures is displayed in the
multifunction display. After af ew minutes of
driving, the current tire pressure of each tire is
shown in the Serv. menu of the multifunction
display.
Example: current tire pressure display
For information on the message display, refer to
the "Checking the tire pressure electronically"
section ( Y
page 264).262
Tire pressure
Wheels and tires