key MERCEDES-BENZ SLC 2017 Service Manual

Setting the air distribution
Air-conditioning system X
Turn the SmartKey to position 2 in the ignition
lock ( Y
page 115).X
Press one or more of the

Problems with the rear window defroster Problem
Possible causes/consequences and P Solutions
The indicator lamp on
the l button flashes.
The rear window
defroster has deactiva-
ted prematurely or can-
not be activated. The on-board voltage is too low because too many electrical consum-
ers are switched on. X
Switch off any consumers that are not required, e.g. reading lamps,
interior lighting or the seat heating.
When the battery is sufficiently charged, the rear window defroster
can be activated again.
The roof is open. X
Close the roof.
When the roof is closed, the rear window defroster can be activated
again.
Switching air-recirculation mode
on/off
General notes If you switch on air-recirculation mode, the win-
dows can fog up more quickly, in particular at
low temperatures. Only use air-recirculation
mode briefly to prevent the windows from fog-
ging up.
Switching on/off X
Turn the SmartKey to position 2 in the ignition
lock ( Y
page 115).X
To switch on: press the r button.
The indicator lamp in the r button lights
up.
i Air-recirculation mode is automatically acti-
vated at high levels of pollution (dual-zone
automatic climate control only) or at high out-
side temperatures. When air-recirculation
mode is activated automatically, the indicator
lamp in the r button is not lit. Outside air
is added after about 30 minutes. X
To switch off: press the r button.
The indicator lamp in the r button goes
out. i Air-recirculation mode deactivates auto-
matically: R
after approximately five minutes at outside
temperatures below approximately 41 ‡
(5 †) R
after approximately five minutes if cooling
with air dehumidification is deactivated R
after approximately 30 minutes at outside
temperatures above approximately 41 ‡
(5 †) if the "Cooling with air dehumidifica-
tion" function is activated
Switching the residual heat on or off
General notes The residual heat function is only available on
vehicles for Canada.
It is possible to make use of the residual heat of
the engine to continue heating the stationary
vehicle for up to 30 minutesafter the engine has
been switched off. The heating time depends on
the set interior temperature.
Activating/deactivating X
Turn the SmartKey to position 0 in the ignition
lock or remove it ( Y
page 115).X
To activate: press the K or V button.
The indicator lamp in the K or V button
lights up.
i The blower will run at al ow speed regardless
of the airflow setting.Operating the climate control systems 111
Climat ec ontrol

Where possible, avoid spinnin gt he drive
wheels when pulling away on slippery roads.
You could otherwise damage the drive train.
SmartKey positions
SmartKey
Z
To remove the SmartKeyG
Power supply for some consumers, such as
the windshield wipersH
Ignition (power supply for all consumers)
and drive positionI
To start the engine
i The SmartKey can be turned in the ignition
lock even if it is not the correct SmartKey for
the vehicle. The ignition is not switched on.
The engine cannot be started.
KEYLESS-GO
General notes Vehicles with KEYLESS-GO are equipped with a
SmartKey featuring an integrated KEYLESS-GO
start function and ad etachable Start/Stop but-
ton.
The Start/Stop button must be inserted in the
ignition lock and the SmartKey must be in the
vehicle.
When you insert the Start/Stop button into the
ignition lock, the system needs approximately
two seconds recognition time. You can then use
the Start/Stop button.
Pressing the Start/Stop button several times in
succession corresponds to the differen tk ey
positions in the ignition lock. This is only the
case if you are not depressing the brake pedal. If you depress the brake pedal and press the
Start/Stop button ,t he engine start si mmedi-
ately.
Ac heck which periodically establishes ar adio
connection between the vehicle and the Smart-
Key determines whether av alid SmartKey is in
the vehicle. This occurs ,f or example, when
starting the engine.
To start the vehicle without actively using the
SmartKey: R
the Start/Stop button must be inserted in the
ignition lock. R
the SmartKey must be in the vehicle. R
the vehicle must not be locked with the
SmartKey or KEYLESS-GO ( Y
page 63).
Do not keep the SmartKey: R
with electronic devices, e.g. am obile phone
or another SmartKey. R
with metallic objects, e.g. coins or metal foil. R
inside metallic objects, e.g. am etal case.
This can impair the functionality of the KEY-
LESS-GO key.
If you lock the vehicle with the SmartKey's
remot ec ontrol or with KEYLESS-GO, after a
short time: R
you will not be able to switch on the ignition
with the Start/Stop button. R
you will not be able to start the engine with the
Start/Stop button until the vehicle is
unlocked again.
The engine can be switched off while the vehicle
is in motion by pressing and holding the Start/
Stop button for three seconds. This function
operates independently of the ECO start/stop
automatic engine switch-off function.
Key positions with KEYLESS-GO
C
Start/Stop button
D
Ignition lock Driving 115
Driving and parking Z

As soo na st he ignition is switched on, al lt he
indicator lamps in the instrument cluster light
up .F urther informatio nons it uations where an
indicator lamp either fails to go ou ta fte rs tarting
the engine or lights up whil ed riving
( Y
page 204).
If Start/Stop button C ha sn ot ye tb ee n
pressed, thi sc orrespond stot he key being
remove df rom the ignition.X
To switc hont he power supply: press
Start/Stop button C once.
The powe rs uppl yiss wi tched on. Yo uc an now
activate the windshield wipers, for example.
The powe rs uppl yiss wi tched off agai ni f:R
the driver's door is opene da ndR
yo up ress Start/Stop button C twice when
in thi sp ositionX
To switc hont he ignition: press Start/Stop
button C twice.
The ignition is switched on.
If yo up ress Start/Stop button C once when
in thi sp osit ion, the ignition is switched off
again.
Removing the Start/Sto pb uttonYo uc an remove the Start/Stop button from the
ignition lock and start the vehicl easn ormal
using the SmartKey. X
Remove Start/Stop button C from ignition
lock D .
Yo udon ot have to remove the Start/Stop but-
ton from the ignition lock when yo ul eave the
vehicle. Yo us hould, however, always take the
SmartKe yw it hy ou when leaving the vehicle. As
long as the Sma rtKe y isint h
e vehicle:R
the vehicl ec an be started using the Start/
Stop button R
the electrically powered equipment can be
operated Starting the engine
Important safety notes
G WARNING
If children ar el ef tu nsupervised in the vehicle,
they could: R
open the doors ,t hu se ndangering other
people or roa du se rs.R
ge to ut and disrupt traffic. R
operate the vehicle's equipment.
Additionally, children could set the vehicl ei n
motion if, for example, they: R
release the parking brake. R
shifting the automatic transmission ou to f
park position P R
Star tt he engine.
There is ar is kofana ccident and injury.
Whe nl eavi ng the vehicle, always take the
SmartKe yw it hy ou and lock the vehicle. Never
leav ec hildren or animals unattended in the
vehicle. Alway sk ee pt he SmartKe yo ut of
reach of children.
G WARNING
Combustion engine se mi tp oiso nou se xhaust
gases such as carbo nm onoxide. Inhaling
thes ee xhaus tg as es lead stop oiso ning. There
is ar is koff ata li njury .T herefore neve rl eave
the engine running in enclose ds paces with-
ou ts uf ficient ventilation.
G WARNING
Flammabl em at erial si ntroduced through
environmenta li nfluence or by animals can
ignite if in contact with the exhaus ts ys tem or
parts of the engine tha th ea tu p. There is ar isk
of fire.
Carry ou tr egular checks to make sure that
ther ea re no flammabl ef oreig nm at erial si n
the engine compartment or in the exhaust
system.
During ac ol ds tart, the engine runs at higher
speed stoe nabl et he catalytic converter to116
Driving
Driving an dp arking

reach its operating temperature. The sound of
the engine may change during this time.
Automatic transmission X
Depress the brake peda la nd keep it
depressed. X
Shift the transmission to position P .
Transmission position display P is shown in
the multifunction display.
i You can start the engine in transmission
position P and N .
Starting procedure with the SmartKey To start the engine using the SmartKey instead
of KEYLESS-GO, pul lt he Start/Stop button out
of the ignitio nl ock.X
Turn the SmartKey to position 3 in the ignition
lock ( Y
pag e1 15) and release it as soon as the
engine is running.
Usin gK EYLE SS-GO to start the engineThe Start/Stop button can be used to start the
vehicl em anually withou ti nserting the SmartKey
into the ignitio nl ock. The Start/Stop button
must be inserted in the ignitio nl ock and the
SmartKey must be in the vehicle. This mode for
starting the engine operates independently of
the ECO start/stop automatic engine start func-
tion. X
Depress the brake peda la nd keep it
depressed. X
Press the Start/Stop button once
( Y
pag e1 15).
The engine starts.
Pulling away
General notes
G WARNING
If the engine spee disa bove the idling speed
and you engage transmission position D or R ,
the vehicl ec ould pul la wa ys uddenly .T here is
ar isk of an accident.
When engaging transmission position D or R ,
alway sf irmly depress the brake peda la nd do
not simultaneously accelerate. ! Change gea ring ood time and avoi ds pin-
ning the wheels. You could otherwise damage
the vehicle.
Depress the accelerator carefully when pulling
away.
The vehicl el ocks centrally once you have pulled
away. The locking knobs in the doors drop down.
You can open the doors from the insid eata ny
time.
You can als od eactivate the automatic locking
feature ( Y
pag e1 73).
It is only possible to shift the transmission from
position P to the desired position if you depress
the brake pedal. Only then is the shift lock
released.
i Upshifts take place at highe re ngine speeds
after ac old start. This help st he catalytic con-
verter to reach its operating temperature
more quickly.
Information on the automatic release of the
electric parking brake ( Y
pag e1 33).
Hill start assist Hill start assist help sy ou when pulling awa yf or-
ward sorinr everse on an uphill gradient. It holds
the vehicl ef or as hort time after you have
removed you rf oot from the brake pedal. This
gives you enoug ht ime to move you rf oot from
the brake peda ltot he accelerator peda la nd to
depress it before the vehicl eb egins to roll.
G WARNING
After as hort time, hill start assist wil lnol on-
ger brake you rv ehicl ea nd it could roll away.
There is ar isk of an accident and injury.
Therefore, quickly move you rf oot from the
brake peda ltot he accelerator pedal. Never
leave the vehicl ew hen it is held by hill start
assist.
Hill start assist is not active if: R
you are pulling awa yonal evel road or on a
downhill gradient. R
the transmission is in position N .R
the electric parking brake is applied. R
ESP ®
is malfunctioning. Driving 117
Driving and parking Z

ECO start/stop function
Introduction The ECO start/sto pf unction switches the
engine off automaticall yift he vehicle is stopped
unde rc ertain conditions.
The engine start sa utomaticall yw hen th ed river
want stop ull away again .T he ECO start/stop
function thereb yh elps you to reduc et he fuel
consumptio na nd emission sofy our vehicle.
Important safety notes
G WARNING
If th ee ngine is switched off automaticall ya nd
you exi tt he vehicle ,t he engine is restarted
automatically. The vehicle may begin moving.
Ther eisar isk of acciden ta nd injury.
If you wish to exi tt he vehicle ,a lways tur no ff
th ei gnition and secure th ev ehicle against
rolling away.
General notes
C
ECO start/sto pd isplay
The ECO start/sto pf unction is activated when-
ever you switch on th ee ngine usin gt he Smart-
Key or th eS ta rt/Sto pb utton.
If th ee ngine has been switched off automati-
cally by th eE CO start/sto pf unction ,t he

Problems with the engine Problem
Possible causes/consequences and P Solutions
The engine does not
start. The HOLD function or Distanc eP ilot DISTRONIC is activated.X
Deactivat et he HOLD function ( Y
page 148) or Distanc eP ilot
DISTRONIC ( Y
page 146).X
Try to start the engine again.
The engine does not
start. The starter motor
can be heard. R
There is am alfunction in the engine electronics.R
There is am alfunction in the fuel supply.
Before attempting to start the engine again: X
Turn the SmartKey back to position 0 in the ignition lock.
or X
Press the Start/Stop button repeatedly until all indicator lamps in
the instrumen tc luster go out.X
Try to start the engine again ( Y
page 116). Avoid excessively long
and frequent attempt stos tart the engine as these will drain the
battery.
If the engine does not start after several attempts: X
Consult aq ualified specialist workshop.
The engine does not
start. You cannot hear
the starter motor. The on-board voltage is too low because the battery is too weak or
discharged. X
Jump-start the vehicle ( Y
page 249).
If the engine does not start despite attempt stoj ump-start it:X
Consult aq ualified specialist workshop.
The starter motor was exposed to at hermal load that was too high.X
Allow the starter motor to cool down for approximately two minutes. X
Try to start the engine again.
If the engine still does not start: X
Consult aq ualified specialist workshop.
The engine is not running
smoothly and is misfir-
ing. There is am alfunction in the engine electronics or in am echanical
componen toft he engine management system.X
Only depress the accelerator pedal slightly.
Otherwise, non-combusted fuel may get into the catalytic converter
and damage it. X
Have the cause rectified immediately at aq ualified specialist work-
shop.120
Driving
Driving and parking

Problem
Possible causes/consequences and P Solutions
The coolant temperature
gauge shows av alue
above 248 ‡( 120 †).
The coolant warning
lamp may also be on and
aw arning tone may
sound. The coolant level is too low. The coolant is too hot and the engine is no
longer being cooled sufficiently. X
Stop as soon as possible and allow the engine and the coolant to
cool down. X
Check the coolant level ( Y
page 233). Observe the warning notes
as you do so and add coolant if necessary.
If the coolant level is correct ,t he engine radiator fan may be faulty. The
coolant is too hot and the engine is no longer being cooled sufficiently. X
At coolant temperatures below 248 ‡( 120 †), drive to the nearest
qualified specialist workshop. X
Avoid heavy loads on the engine as you do so, e.g. driving in moun-
tainou st errai na nd stop-and-go traffic.
DYNAMIC SELEC Tb uttonUse the DYNAMIC SELECT button to change the
drive program. Depending on the drive program
selected the following vehicle characteristics
wil lc hange: R
the drive (engine and transmission manage-
ment) R
the suspensio n( vehicles with adaptive
adjustabl ed amping or AMG sports suspen-
sion) R
the steering R
the availability of the ECO start/stop function
Each time you start the engine with the Smart-
Key or the Start/Stop button, drive program C is
activated. For further information about starting
the engine, see ( Y
pag e1 16).
X
Press DYNAMIC SELECT button C as many
times as necessary until the desired drive
progra miss elected.
The selected drive progra ma ppears in the
multifunction display. After as hort time the displa yg oes out and the status icon of the
selected drive progra ma ppears.
In addition, the current drive progra ms ettings
are displayed briefly in the multimedi as ystem
display.
i In af ew countries, the ECO start/stop func-
tion is deactivated at the factory due to the
available fuel grade. In this case, the ECO
start/stop function is not available in any
drive program, regardless of the displa yint he
multimedi as ystem display.
Availabl ed rive programs:
C Comfort Comfortabl ea nd economi-
cal driving characteristics
S Sport Sporty driving characteris-
tics
S+ Sport Plus Particularly sporty driving
characteristics
I Individual Individua ls ettings
E Economy Particularly economical
driving characteristics
Additional information for drive programs
( Y
pag e1 25).DYNAMI CS ELEC Tb utton 121
Driving and parking Z

The current transmission position and drive pro-
gram appear in the multifunction display.
Engaging par kp osition PX
When the vehicle is stationary, depress the
brake pedal. X
Press button C .
Engaging par kp osition Pa utomaticallyPark position P is automatically engaged if:R
you switch off the engine using the SmartKey
and remove the SmartKey R
you switch off the engine using the SmartKey
or using the Start/Stop button and open the
driver's door or front-passenger door R
the driver's door is opened when the vehicle is
stationary or driving at very low speed and the
transmission is in position D or R
Under certain conditions, the automatic trans-
mission shifts automatically to transmission
position P if the HOLD function or Distance Pilot
DISTRONIC is activated. Observe the informa-
tion on the HOLD function ( Y
page 148) and on
Distance Pilot DISTRONIC ( Y
page 144).
Engaging reverse gear R
! Only shift the automatic transmission to R
when the vehicle is stationary. X
Depress the brake and keep it pressed. X
Push the selector lever forwards past the first
point of resistance.
The ECO start/sto pf unction is not available
when reverse gear is engaged. Further informa-
tion on the ECO start/sto pf unction
( Y
page 118). Shifting to neutral N
G WARNING
If children are left unsupervised in the vehicle,
they could: R
open the doors, thus endangerin go ther
people or road users. R
get out and disrupt traffic. R
operate the vehicle's equipment.
Additionally, children could set the vehicle in
motion if, for example, they: R
release the parking brake. R
shiftin gt he automatic transmission out of
park position P R
Start the engine.
There is ar isk of an accident and injury.
When leaving the vehicle, alway st ake the
SmartKey with you and lock the vehicle. Never
leave children or animals unattended in the
vehicle. Always keep the SmartKey out of
reach of children. X
When the vehicle is stationary, depress the
brake pedal. X
Push the selector lever forwards or back to
the first point of resistance.
If you switch the engine off with the transmis-
sion in position R or D ,t he automatic transmis-
sion shifts to N automatically.
With the SmartKey: if you then open the driv-
er's door or the front-passenger door or remove
the SmartKey from the ignition, the automatic
transmission shifts to P automatically.
With KEYLESS-GO: if you then open the driver's
or front-passenger door, the automatic trans-
mission shifts to P .
If you want the automatic transmission to
remain in neutral N ,e .g. when having the vehicle
cleaned in an automatic car wash with at owing
system: X
Vehicles with KEYLESS-GO: remove the
Start/Stop button from the ignition lock. X
Insert the SmartKey into the ignition lock. X
All vehicles: switch the ignition on. X
Depress the brake pedal and keep it
depressed. X
Shift to neutral N .Automatic transmission 123
Driving and parking Z

X
Releas et he brak ep edal .X
Releas et he electric parking brake.X
Switc ho ff th ei gnition and leav et he SmartKey
in th ei gnition lock.
Engaging drive position D X
When th ev ehicl eiss ta tionary, depress th e
brak ep edal .X
Push th es elector lever bac kp ast th ef irst
poin tofr esistance.
Transmission positions E Par kp osition
This prevents th ev ehicl ef ro mr ollin g
away when stopped.
Only shif tt he transmission int op osi-
tion P when th ev ehicl eiss ta tionary
( Y
page 122). The parking loc k
should no tbeu sed as ab rak ew hen
parking .A lways apply th ee lectronic
parking brak eina ddition to th ep ark -
ing loc kino rder to secure th ev ehi-
cle .
If th eS ma rtKey is remove df ro mt he
ignition lock, th et ra nsmission is
locked.
The automatic transmission shifts
int o P automatically: R
when th eS ma rtKey is remove d
from th ei gnition loc kR
when th ee ng in eiss witched off
wit ht he transmission in position R
or D and on eoft he door si s
opened
If th ev ehicl ee lectronics are malfunc -
tioning ,t he transmission may be
locke dinp osition P .H av et he vehicl e
electronics checke di mmediately at a
qualified specialist workshop.
F Revers eg ear
Only shif tt he transmission int op osi-
tion R when th ev ehicl eiss ta tionary. D Neutral
Do no ts hif tt he transmission to N
while driving .O th erwise, th ea uto -
matic transmission could be dam-
aged.
No powe rist ra nsmitte df ro mt he
engin etot he driv ew heels.
Releasing th eb rak ep edal will allow
you to mov et he vehicl ef re ely, e.g. to
push it or to wi t.
If ES P ®
is deactivated or faulty: shif t
th et ra nsmission only to position N if
th ev ehicl eisind anger of skidding,
e.g. on icy roads.
! Rollin ginn eu tral N can damag e
th ed riv et ra in .
: Drive
The automatic transmission changes
gear automatically. All forward gear s
are available.
Driving tips
Changing gear The automatic transmission shifts to th ei ndi-
vidual gear sa utomatically when it is in trans -
mission position D .T his automatic gear shifting
behavior is determine db y:R
th es elected driv ep rogramR
th ep osition of th ea ccelerato rp edalR
th er oad spee d
Accelerator pedal position Your style of driving influence sh ow th ea uto -
matic transmission shifts gear :R
littl et hr ottle: earl yu pshift sR
mor et hr ottle: lat eu pshift s124
Automati ct ra nsmission
Driving and parking